Drinky Crow
at 1:55pm 04.15.21
2/398
Guess it were installed to improve airflow over main attached with its bolt rope maybe? Tides say be
|
||
Close Call (2)
Roland5048
at 11:58am 04.15.21
15/1533
Sunday, 4/11 about noon, apparently a small tornado or possible waterspout came through our marina.
|
||
wynkoop
at 11:29am 04.15.21
11/3076
So I mounted Bottoms Up's rudder the other day. Discovered I needed a 3/16 clevis pin and retainer,
|
||
toscatara
at 10:23am 04.15.21
1/458
good afternoon I need to change this portlights, does anyone know what model it is? thank
|
||
YVRguy
at 7:25am 04.15.21
16/3024
On our boat Ge'Mara, the dinghy has always been something of a conundrum. Our first dinghy, the one
|
||
mmlspace
at 6:14am 04.15.21
14/2385
My Hunter only has single bow cleat and two stern cleats. If love to add two midship cleats for doc
|
||
IÑAXIO
at 1:57am 04.15.21
19/1614
|
||
kendyoozed
at 9:40pm 04.14.21
6/2162
|
||
thetone
at 9:07pm 04.14.21
1/738
Hello, I'm thinking of purchasing this used backstay adjuster for my 1990 35s5. Does anyone have ex
|
||
Jerdavis77
at 8:30pm 04.14.21
5/1279
|
||
Zeppelin RIBS (3)
thetone
at 7:43pm 04.14.21
7/3077
Hello, I am considering purchasing a Zeppelin Zulu Hypalon 260 RIB. Mine was stolen last summer. Do
|
||
DArcy
at 7:01pm 04.14.21
2/555
In the year I've owned this boat I've come to realize there were a lot of sketchy things done with t
|
||
kendyoozed
at 3:24pm 04.14.21
24/3108
I'm getting back into sailing after 16 years. Looking for a bot that my family of 4, kids are 16'13,
|
||
SEMPERAVANTI41
at 12:59pm 04.14.21
4/857
I have had to have the cylinder head removed and machined and the valves replaced due to salt water
|
||
Red_Dog
at 9:46am 04.14.21
4/1428
When purchased my Hunter 28.5, the boat had an Ida Sailor Marine rudder. It was installed by a PO fo
|
||
chdeist
at 9:39am 04.14.21
6/1958
|
||
HansZelf
at 8:42am 04.14.21
3/1166
Hi, I am buying a Catalina 440 (2005) but need to buy an anchor chain. The old one has been lost...
|
||
shemandr
at 6:49am 04.14.21
22/2338
The Weather Channel had a report about a capsizing in the GOM yesterday afternoon. They reported 3
|
||
Andrew Dobson
at 6:37am 04.14.21
11/1835
Good morning fellow sailors I am looking at fitting marine A/C on my 35 in the next couple of month
|
||
John Marrone
at 4:37am 04.14.21
11/1549
Looking for some help with challenges leaving a boat at mooring, maintenance, battery charging, canv
|
Express 34 - Flooring Refinish
kloudie1 at 12:54pm 11.17.24 As Kappy says, the veneer is very thin. The veneer is available to glue to the substrate if an oopsi |
||
New main sail too tall. Now what?
SycloneDriver at 12:48pm 11.17.24 I just measured the main sail luff at 420 inches. The new sail is 425 inches. I'm guessing that NS |
||
Express 34 - Flooring Refinish
kappykaplan at 12:30pm 11.17.24 Congratulations on your first post! :beer: It's normal for the sole to be a veneer on plywood - your |
||
Vented Loop
nabalab at 10:05am 11.17.24 Is a discharge vented loop required when the holding tank is located higher than the head? |
||
Hunter 38 Lithium Ideas (6)
jssailem at 8:46am 11.17.24 I personally would never charge any LFP to more than 14.2v and if the cells are a bit imbalanced, I |
||
Hunter 38 Lithium Ideas
Hayden Watson at 7:49am 11.17.24 If the voltage for a lifepo4 is too low, it will take a long time to balance the cells and could r |
||
S2 9.2a new owner
kappykaplan at 7:47am 11.17.24 Any thought about doing that versus staying with in hull glued version? Not an S2, but . . . My sp |
||
Suzuki 2.5 on 8- Foot Trinka
dLj at 7:30am 11.17.24 I understand about moving forward with the extension on the handle, but I was noting that the Suzuk |
||
Battery shelf
Ward H at 7:17am 11.17.24 I've done a bit of fiberglass and wood removal on my boat. If it is round I use a hole saw. If it |
||
Taking the mast down
sailme88 at 6:08am 11.17.24 One question; were the wiring connectors stowed in the mast base? I'm going to have ours taken down |
||
Taking the mast down
SawyerCurt at 5:55am 11.17.24 One question; were the wiring connectors stowed in the mast base? It depends. On mine, they are |
||
Battery shelf
shemandr at 4:14am 11.17.24 Is the shelf tabbed to the hull? 5200? If it's the ladder the plywood may need to be peeled off i |
||
Hull sag problem
shemandr at 3:20am 11.17.24 Indeed, and true of carbon fiber too. Sometimes the cracks can be, shall we say, substantial. :yike |
||
Hull sag problem
Will Gilmore at 3:09am 11.17.24 Sitting on a trailer for that long may also cause, what a lot of people refer to as, oil canning. A |
||
Suzuki 2.5 on 8- Foot Trinka
Blitz at 9:39pm 11.16.24 Blitz . The extension goes on the throttle . This allows you to sit further forward on the boat . I |
||
Taking the mast down
Project_Mayhem at 8:34pm 11.16.24 One question; were the wiring connectors stowed in the mast base? I'm going to have ours taken down |
||
Hull sag problem (1)
Davidasailor26 at 7:35pm 11.16.24 Fiberglass boats "banana" from having the backstay pumped tight. This drives the mast down and pull |
||
Suzuki 2.5 on 8- Foot Trinka
Skipper J at 7:16pm 11.16.24 Lol. Red-faced two-handed yanks on the side straps solved the problem. |