Serving sailors online since 1997
 
 

Recent Topics

T37 Phil at 3:46am 02.26.07
13/1645
Most of the blisters I've seen in pictures or on other boats have been fairly extensive and irregula
Alan at 4:35am 02.26.07
0/1707
Has anyone applied for their IRC certificate yet? If so, what boat and what's your rating?
Jerry Cann at 4:30am 02.26.07
2/3370
Pacific Seacraft Taps Robert H. Perry for New Model. At a national conference of Pacific Seacraft
James10044 at 4:56am 02.26.07
5/1027
I have lost the centerboard to my 1980 30' oday. I need info on where I can get a centerboard or pl
NautiDuck at 4:45am 02.26.07
3/1267
I have been trying to find a license plate bracket for Catalina Yachts. I would think there is such
Penbodlas at 6:16am 02.26.07
1/1128
I am going to convert my boat (MacGregor 26C) from a trailer-sailer to one on a saltwater mooring (s
Tim Haibach at 6:19am 02.26.07
3/1914
A Yahoo Group was recently launched that is catered toward Catalina 27 or 270 owners. Since we are g
oceansail0 at 6:31am 02.26.07
4/1180
I have an h31 (1984). I do not need a gps tracker normally. I will be taking a few week long trips t
Scott at 7:01am 02.26.07
5/3815
I need to rebuild or replace my Perkins 4.154 in my `79 Outisland 41. It looks like about $7K to re
Margaritaville at 7:16am 02.26.07
13/1301
I have been considering trying to race my 31H Previous owners have had some luck with her when she
Allan R at 7:57am 02.26.07
7/2228
For anyone interested, attached is the review of the Catalina 36 in the March Boat US magazine (may
Chet7135 at 10:07am 02.26.07
47/3203
Ok, I have to buy batteries, I was planning to buy seagel or any kind of gel battery, but not sure
Douglas Washburn at 10:05am 02.26.07
7/1116
Our boat has the horseshoe banquet seating configuration. The table (original equipment, I believe)
Chuck Turner3968 at 9:56am 02.26.07
1/1070
I know this subject has been covered many times, but instead of looking in the archives, I would lik
John at 9:19am 02.26.07
12/1157
Has any one ran there lines to the cockpit on a 26 it looks too tight to do this...any suggestions ?
Bob f at 10:46am 02.26.07
3/1045
Just purchased a new Icom M422 for my Hunter. couple install questions that the manual is a bit fogg
Philip Toren at 11:00am 02.26.07
1/1271
My overboard discharge valve from the head is stuck in the discharge position. So far I haven't been
Alex at 11:14am 02.26.07
4/994
Hey, All. Did enyone ever consider an elecreic winch for a swing keel? Seems like you can pick up a
windsmaker at 11:27am 02.26.07
1/989
I'm thinking about buying a ericson 38 . Anyone familiar with the sailing characteristics of this m
tom Gardner at 4:38pm 02.26.07
7/4199
I have found a 1974 Ranger 26. I raced against one years ago up in SF bay. It seemd to race will t

Recent Replies

New toilet and holding tank system
Peggie Hall HeadMistress at 8:57pm 09.07.21
I haven't examined the whole plumbing run but it is controlled by a gate valve that lets the water i
Bilge Pump - Siphon BACK!
FastOlson at 7:48pm 09.07.21
One of the best ways to address the dangers and shortcomings of a centrifugal pump (like the cheap a
Depth sounder and speed stoped working
SoSound at 7:19pm 09.07.21
Check the network settings and find the sources for you data on your Zeus MFD, see if your transduce
HUNTER 376 Halyard Installation
pparker99 at 7:05pm 09.07.21
I've seen spars marked that way, it boggles my mind, the label really should say, "spare jib halyar
HUNTER 376 Halyard Installation
Sailfanatic at 6:51pm 09.07.21
Ah, thanks for bringing up point needing clarification! Halyard is for asymmetrical spinnaker. The
HUNTER 376 Halyard Installation
pparker99 at 6:48pm 09.07.21
I think you are on the right track on feeding the halyard down the mast. Do you have a spare sheave
HUNTER 376 Halyard Installation
pparker99 at 6:40pm 09.07.21
Ah, thanks for bringing up point needing clarification! Halyard is for asymmetrical spinnaker. The m
luger 27 fairwinds safe for icw or Florida sailing
slash19781 at 6:38pm 09.07.21
well i appreciate the comedic factor of that reply but in no way was that helpful lol A for effort t
What would you change in this plan? (fiberglass part of a rotten core job)   (5)
Rabe at 6:38pm 09.07.21
Got the new core installed, epoxied and old skin put on. Still have to bevel and glass the kerfs thi
Power washing the bilge?   (1)
Hayden Watson at 6:30pm 09.07.21
My posts are probably some of those you found mentioning pressure washing. I have done it twice in t
Shoal vs Wing Keel
Sailfanatic at 6:28pm 09.07.21
A deep keel model will well out sail either a wing keel or shoal draft, buy a short keel only if its
If you had one of these...
Will Gilmore at 6:28pm 09.07.21
My grandmother had one exactly like Brian's picture. You could change the channel by rattling a set
Depth sounder and speed stoped working
Don S/V ILLusion at 6:27pm 09.07.21
The first step would be to see if power is getting to the instruments
HUNTER 376 Halyard Installation
Sailfanatic at 6:19pm 09.07.21
Thanks mate! Yes, have empty sheave and mast exit. Thanks for the tip on Rig Rite. I just got a "ma
New to me O'day 28 - Getting into the water, re-rigging and running lines
jssailem at 6:12pm 09.07.21
Congrats on the new to you boat Terry-Buda Running rigging is a 4-5 out of 10 on the DIY scale. Ri
Bilge Pump - Siphon BACK!
Sailfanatic at 6:12pm 09.07.21
If the bilge pump outlet is below water when the boat is heeling, and there is no check valve or ant

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.