Manny
at 12:24pm 07.13.07
1/876
Hi all,I have a CDI furler for my jib. Lately I've noticed with jib all the way out and in decent
|
||
jamboo
at 12:55pm 07.13.07
2/1001
Working on a project to run main and jib halyards back to cockpit.One of the halyard goes up out o
|
||
oreana123
at 1:18pm 07.13.07
15/1121
I have been working on a 26D making improvements to the generaL livability including such things as
|
||
breadman
at 3:21pm 07.13.07
6/1420
I did it my daughter and I turned the critter over in the yard, we slid it off the trailer and once
|
||
TN
at 4:16pm 07.13.07
8/1571
My H27 is less than 2 years old and is equipped with the infamous Jabsco toilet. I greased the pump
|
||
Rich Golden
at 4:15pm 07.13.07
2/967
HELP! have't had her in the water since 4 June 07. Had to replace the impellar from damage from PO,
|
||
Ctskip
at 2:30pm 07.13.07
3/1058
I am looking into getting a inflatable dingy, and I was thinking about an electric motor for it. The
|
||
Charm
at 9:56pm 07.04.07
7/1024
My '83 Mac 25 is very, very close to launching. I have a couple of quick questions.First off, I ha
|
||
Tim Haibach
at 12:27am 07.05.07
1/1313
My 1985 C27 has a roller furler installed (FACOR) with a continuous running line vs. rolling up arou
|
||
sea_casper
at 1:26am 07.05.07
4/1043
I am thinking of replacing my main sheet, Hunter 26 spec and existing sheet is 70 feet, this is too
|
||
Wallace Shakun
at 1:34am 07.05.07
2/839
Looking for rubber boots for toggle switches foundon the "C" engine panel.
|
||
ted
at 1:55am 07.05.07
5/4934
I took a look at an H450 last week. It was on dry storage. The keel to hull joint had some peeling a
|
||
Pat
at 11:56pm 07.04.07
1/1148
I have the Autohelm (Raymarine)ST 50 system -wind, depth, speed, GPS, chartplotter. The speed was wo
|
||
Sailorman20824
at 11:51pm 07.04.07
2/2401
I have a 1980 (approximately) Catalina 25 and need a wiring diagram for the electrical system. Any
|
||
Joe Mullee
at 11:39pm 07.04.07
5/1067
This may bea dumb question but here goes. When I remove the cover to the air filter on the engine th
|
||
Timo42
at 1:58am 07.05.07
1/889
I have a Tohatsu 6hp 4stroke pushing my mac 22, just noticed that the propeller has a bent blade. It
|
||
Abby Normal
at 3:27am 07.05.07
6/1278
If any of you saw the flooding in SE Kansas on TV this week (especially Coffeyville), it's all windi
|
||
Tim Horvatich
at 3:39am 07.05.07
7/1244
We had our own fireworks on the Fourth of July. Sailing reefed in brisk 12-20 knot winds we were ha
|
||
Bo
at 2:20am 07.05.07
6/1352
Looking around the internet, the prices for new mail sails runs the full spectrum. I might consider
|
||
Mike16400
at 2:15am 07.05.07
1/933
Im sailing my 2007 Hunter 25 from Hyannis to Nantucket this weekend, and am not sure how the reefing
|
Boat ID please
Terry Cox at 2:23pm 07.13.21 My guess is a Sparkman and Stephens. Very similar lines. |
||
Dinghy Security (3)
Charlie98117 at 1:51pm 07.13.21 This thread is a bit old but I thought I would post my solution to securing a Torqeedo to the dinghy |
||
Do we have a Battery or a Fridge issue?
RitSim at 1:37pm 07.13.21 I agree that the batteries are the root cause of the problem. |
||
Do we have a Battery or a Fridge issue?
RitSim at 1:36pm 07.13.21 Some of the freezer compressor modules have low voltage protection and shut off automatically so the |
||
Do we have a Battery or a Fridge issue?
Benny17441 at 1:28pm 07.13.21 Don't know how many batteries does your house bank has, but if it is less than 3 take them out and |
||
Autohelm
MikeHoncho at 1:15pm 07.13.21 The Autohelm 3000 has seatalk compatibility(http://www.busse-yachtshop.de/pdf/rayST3000_wheel.pdf). |
||
Mac 25 upper shrouds & spreader positioning (1)
whudatt at 12:53pm 07.13.21 Thank you for your reply ! this is what it looks like now,the manual says to measure down 11ft from |
||
LED Anchor Light
KZW at 12:22pm 07.13.21 In mast furled. I will need to research notes on the ascenders. Any good climbing gear store will h |
||
Pop-up assist for Venture 25
Captain Ron 18 at 12:16pm 07.13.21 I installed gas struts on my Mac 25..20 inch/90LB. Works great. Do you still use the support pol |
||
LED Anchor Light
AwwShucks at 12:02pm 07.13.21 BC Bernie - do you have an in mast furling or traditional main sail? Additionally, do you have a li |
||
Casting
Benny17441 at 11:48am 07.13.21 It came to me that today we have computer 3D printing. In my college years many moons ago I worke |
||
Rigging the 2nd reef in a 310?
Parsons at 11:40am 07.13.21 Not a 310 owner, but some general questions that may help: If you have any slugs between the second |
||
Gauges that do not fog
Benny17441 at 11:38am 07.13.21 Production boats do not usually come with EOM temperature gauges so I would think you may have an af |
||
Bilge Drainage?
SirMichael at 11:34am 07.13.21 Benny, Many thanks for the reply. That does answer my question. I'll probably follow up |
||
Bilge Drainage?
Benny17441 at 11:22am 07.13.21 To answer your question, yes there are areas in the hull that will not drain into the bilge. The p |
||
GFCI trouble shooting
Scott T-Bird at 11:12am 07.13.21 The other part of the problem is that from time to time boats seem to get unplugged for one reason |