Serving sailors online since 1997
 
 

Recent Topics

Carl at 11:55am 10.21.07
3/1411
I have 1978 Hunter 30 and after pulling it out of the water I noticed a crack on each side of the fi
bobf at 1:17pm 10.21.07
6/1199
I am having a problem with the starter solenoid clicking then engaging after several tries at starti
dennis m mormile at 3:23pm 10.21.07
3/1324
what do you good sailors recommend to put the boat away for the winter?
Syversens at 2:53pm 10.21.07
2/1431
hello all, I have a big problem with my spreaders tearing up my jib. this weekend I had a long race
caguy at 3:57pm 10.21.07
0/1735
warnings. NOAA was predicting 5 ft seas and 45 mph winds with 60-80 mph gust. I almost didn't go out
BananaToe at 4:16pm 10.21.07
9/1979
We're debating what type of cabin heat to install. Today we use a little AC unit, but the light does
jk kudera at 8:08pm 10.19.07
1/1248
We have a 1984 Hunter 34 and have had an Island Nautical dodger for years, it was destroyed, and I n
leo Ganter at 8:29pm 10.19.07
0/1300
There is a casts iron fitting at the bottom of the mast. This area sits into the deck to hold it in
Leo Ganter at 8:34pm 10.19.07
3/1539
The cast iron foot on my mast has been damaged. I need to either get a replacment or repair the exis
Rudy G at 9:40pm 10.19.07
2/845
I would to protect my boat against lighting strikes. One of the methods I was contemplating is to cl
Rich (P303) at 10:25pm 10.19.07
20/2021
Top off tank and add additive... or drain tank for the winter storage?
Johan23875 at 1:02am 10.20.07
1/1399
Hello All I cannot find on this web site information on the (what I believe some call it) a hard gl
Ken Prichard at 1:54am 10.20.07
13/1553
I recently asked two specific questions regarding the use of marine radar. After some reseach involv
mark7478 at 2:59am 10.20.07
2/1257
It's time to start thinking about removing the bottom paints from my E25 and start a new process of
arrhythmia at 3:00am 10.20.07
0/1279
I'm replacing the ceiling in my O'Day 34, and it was a soft vynal, or naugahide material that lays o
Morry at 4:43am 10.20.07
1/889
I have a 1993 Hunter 23.5. The trailer appears to be the original Hunter model which came with the
Gary Eglinton at 5:30am 10.20.07
5/5785
2003 Beneteau 473. Aft head: standard Jabsco 29090 manual; forward: standard Jabsco electric 37010
Nestor at 5:19am 10.20.07
1/1005
Changing the cutless bearing and shaft from a 3/4 inch to a one inch in both the hull packing glan a
Steve at 5:15am 10.20.07
Cal
1/580
Hello fellow Cal owners. Looking for a Cal 34 mast. My mast was damaged in the recent wind storm. It
Bill Arneson at 5:48am 10.20.07
0/948
Check out the October Boat US Seaworthy, page 15.Looks like a H33 getting pounded by the surf,feel b

Recent Replies

Marelon Seacock fail!
Ralph Johnstone at 5:25pm 10.29.21
Because it is not a problem with Teflon tape. Picky, picky, picky. It's all about semantics:face
Marelon Seacock fail!
thinwater at 4:32pm 10.29.21
I might consent those points but I contacted the Tech rep for Marelon at Forespar.com and he told m
Heat exchanger zinc anode.
Davidasailor26 at 4:26pm 10.29.21
What will be the best time to paint hull and bottom? Have to launch by April 15 2022. Do check the
What make/size of Anchor for 2005 Hunter 33?
Terry Cox at 4:16pm 10.29.21
I just took a large Danforth off my boat and brought it home to the garage. What would you recommen
Fuse in small solar setup
dmax at 4:05pm 10.29.21
Regarding the wiring, the Renogy panels come with MC4 plugs already installed, you'll want to get an
Ericson 27 water fill
Guy Erdman at 4:03pm 10.29.21
Guy, I'm in Port Jefferson. The boat is on the hard for the winter. I used to own an Ericson 32-3,
Sticky, no sticky.
kloudie1 at 3:59pm 10.29.21
I don't know, Tom. Some of my "rubber" coated items feel like they are covered in 5 day old pancake
Its funny Friday!
DaveJ at 3:38pm 10.29.21
Its funny Friday!
Will Gilmore at 3:35pm 10.29.21
Do you look to see what tack the other cars at an intersection are on to determine right of way? Th
Wire tied set screw for prop shaft flange
Hayden Watson at 3:27pm 10.29.21
Not necessarily. It is my understanding that the holding strength of Loctite in general varies wit
Marelon Seacock fail!
Hayden Watson at 3:25pm 10.29.21
Why not just name the thread "Teflon Phhhhhhtttttttttt". Because it is not a problem with Teflon
mainsail shape for proper furling
bradm at 3:20pm 10.29.21
Thanks all for the replies. Re-reading the suggested links, I notice a few mentions of barber-pole
Ericson 27 water fill
TimFromLI at 3:20pm 10.29.21
Guy, I'm in Port Jefferson. The boat is on the hard for the winter. I used to own an Ericson 32-3,
Fuse in small solar setup
dlochner at 3:12pm 10.29.21
At a minimum the fuse should go between the unregulated power source and whatever else. Which means
170 Gooseneck Repair
Tater at 3:08pm 10.29.21
Welcome to the forum!! Please post a photo of the boom and gooseneck connected to the mast. Why re
Ericson 27 water fill
Tally Ho at 3:06pm 10.29.21
DIY Fuel Polishing System
jmce1587 at 2:39pm 10.29.21
When I have a flash of an idea, especially in the evening after a glass or two of wine, I try to pu
Running hot
Johnb at 2:38pm 10.29.21
dlochner said At a personal level, understanding why and how something works is far more valuable t
DIY Fuel Polishing System
senang at 2:28pm 10.29.21
Fuel polishing system is a circulating pump, a particle filter, a water separator (often combined) a

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.