Serving sailors online since 1997
 
 

Recent Topics

pclarksurf at 6:28pm 08.01.21
3/638
196687196688
kodiak1120 at 6:25pm 08.01.21
6/1053
I just installed two new 6.5" speakers in the cockpit of my Beneteau 37. I had to cut the holes a l
DAVA390 at 4:57pm 08.01.21
3/649
Shortly after purchasing my Precision 23 8 years ago i discovered that i had been hoodwinked. About
CaptBob at 3:19pm 08.01.21
8/2115
Hi, I have a new 315 on order and was wondering about instrument placement. I am only having the i7
Michael Davis at 3:13pm 08.01.21
13/2654
196682 Again , we are the only two boats here. Solitude so close to home.
Voyager1 at 2:06pm 08.01.21
0/519
1. Has anyone replaced stem seal without removing the head on a Yanmar 2gm20f. Is it reasonable poss
john6206 at 12:32pm 08.01.21
2/728
Hey everyone, Exactly a year ago I bought a Mercury 5hp propane sail drive motor. So naturally i g
Voyager1 at 11:17am 08.01.21
3/857
1. Has anyone replaced stem seal without removing the head on a Yanmar 2gm20f. Is it reasonable poss
SailorElliot at 10:16am 08.01.21
17/5852
Hello! I was wondering what the "weather limits" are for a Flicka 20 (example: 30 knots of wind, 4
jssailem at 8:25am 08.01.21
2/1067
waterman30 at 7:08am 08.01.21
18/3831
Hi. I am new to the forum. I have never owned a water ballast boat before but am considering a 240.
apagano at 4:48am 08.01.21
3/678
Hello all, i have a Hunter 49 that almost all stock latches, both doors and drawers have mostly fail
patbratton at 3:26am 08.01.21
3/936
The bilge area under the rear if the cockpit has about three inches of water. there are no limber ho
Yangyangyyy at 9:04pm 07.31.21
3/622
I'm trying to Change the fuel cap and seat ( on port stern deck) on my 2003 Beneteau first 36.7 Sin
dLj at 5:42pm 07.31.21
78/10148
I am not well versed in using all chain anchor rode. So I've been researching chain snubbers. I fin
Dil at 2:56pm 07.31.21
30/3243
Recently I purchased a new sail Today I noticed near the head of the sail the leach makes contact wi
Apex at 2:28pm 07.31.21
5/840
Putting out in another thread as well, but have friend with hunter 34 that just lost shaft, strut an
Apex at 2:27pm 07.31.21
2/418
Friend collided with ufo, which tor blade off prop and took the strut. No leaking , but they are loo
Ottdreamer at 1:23pm 07.31.21
14/1986
Might one of you fine Canadian sailors be looking to part with a hunter 260, wheel preferred. My dr
Shanelee78 at 10:40am 07.31.21
4/1147
Hello everybody. We just purchased a 1979 oday 19. We live on a little lake in Pierceton Indiana a

Recent Replies

What can I expect in performance gain VHF?
BrianQ at 9:35am 03.05.25
You can't change physics, so it would be unreasonable to expect VHF LOS communications over the dist
how to access the toilet valve at sea
SkiingSailor at 8:49am 03.05.25
hopefully ALL your below-waterline "sea access" valves are easy to access... to be able to turn off
Assortment of cheap fixes on Cat 22   (2)
Jacktar at 8:48am 03.05.25
Couple of live shots from my boat of the foiling boats in pensacola bay last weekend
SSB ground Plane Option
SkiingSailor at 8:46am 03.05.25
Tried all the diagnostics - my shroud-mounted antenna is not doing the job. Has anyone used this ?
Jib needed Hunter 216
shemandr at 8:30am 03.05.25
Catalina sliding gooseneck recommendation
Joe at 8:23am 03.05.25
Thanks for the responses all. Based on the linked threads and others' comments, it seemed having
Yet Another Docking Challenge
sesmith at 7:48am 03.05.25
Another idea. Pull boat in for a port side tie, kind of deep in. Run a spring line from the starb
Yet Another Docking Challenge
Captain Larry-DH at 7:09am 03.05.25
Some good advice above. If you go in bow-first and do a port tie you won't need to do very precise m
Jib needed Hunter 216
kappykaplan at 7:04am 03.05.25
Where is Amity Harbor? Copiague, New York
Oday 22 structural question
colemj at 7:01am 03.05.25
Some of the later O'Days skipped the tabbing to the hull. The bulkhead is held into a slot in the l
2000 Oceanis 411 Rudder Issue
Syl at 6:50am 03.05.25
We have a 1998 B411 with the carbon rudder post. Our helming stiffness only seems to be an issue wh
Yet Another Docking Challenge
jssailem at 6:47am 03.05.25
The end dock strategy with spring line sounds like a solid option. Worth a try. Certainly there is g
C275 Spinnaker Tricks
PMK at 6:43am 03.05.25
I tried the top down furler just once, then it went back in the box. I have been racing my C275 for
Roller furling
BrianQ at 5:58am 03.05.25
If the furler is OEM it should be a Hood 800 SL. If so, there are two screws at the bottom of the d
Yet Another Docking Challenge
dlochner at 5:51am 03.05.25
This is pretty funny. I just pulled this up on Google Maps to see if I could get a better look. i
Oday 22 structural question
Project_Mayhem at 5:46am 03.05.25
If you want to lighten those bulkheads, then paint them or glue a white laminate on them. If they
Oday 22 structural question
dlochner at 5:45am 03.05.25
If you want to lighten those bulkheads, then paint them or glue a white laminate on them. If they
Fuel leak on my Yanmar 3GM30F engine in my 1987 Hunter 34.
kloudie1 at 5:24am 03.05.25
Scented stuff aside, the injector pump has a bleed screw on top of the banjo bolt at the fuel line i
Jib needed Hunter 216
shemandr at 5:18am 03.05.25
Where is Amity Harbor?
Hunter 34 primary winches   (2)
kloudie1 at 5:12am 03.05.25
My previous owner added the Lewmar 43'ss .. Everything works .. as you can see, the Lewmars are forw

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.