Serving sailors online since 1997
 
 

Recent Topics

emalsyd at 10:14pm 12.17.07
2/2438
thinking about replacing my traveler which is currently located in the cockpit and attaches to the e
crzhors at 10:12pm 12.17.07
1/1018
Merry Xmas! I have posted a picture of our mast step, which brigdes over the keel and bilge.We have
Kim at 10:20pm 12.17.07
4/940
Oday 26 w/ Johnson 9.9 O/B I'm having to move my boat due to a relocation. The only place where I
Jules Robinson at 11:25pm 12.17.07
3/2371
Hello, I have been looking for articles or reviews on the Fantasia 35. I can't find any. I did fi
Richard Deep at 12:26am 12.18.07
5/1550
Well, I decided to replace the standing rigging on my 85 H-31 (it's original!). In talking with the
Ted at 1:04am 12.18.07
8/1059
Has anybody passed through Hudson River - Erie Canal and Oswega Canal to Lake Ontario with a 6 feet
PDXnative at 12:46am 12.18.07
4/1908
I have been reading that a lot of the 1980's Beneteau's had blister problems. Anyone know what years
walt at 1:44am 12.18.07
35/3097
Earlier here, I was asking about ways to keep the boom up during main sail reefing (usually done whe
ernierogers at 1:15am 12.18.07
17/3006
I replaced the Wema level sensor sending units in both my fresh water and waste holding tanks about
Rick D at 6:14am 12.18.07
0/777
It's stuck. See the link for a recent update. Rick D
navis at 5:02am 12.18.07
7/1320
We need to replace our port curtains and are having a tough time finding someone to do the work (at
Fred3886 at 5:01am 12.18.07
3/1303
I'm trying to locate the center of gravity or balance point information for my newly purchased O'Day
Ted at 3:30am 12.18.07
2/1356
Has anybody passed through Hudson River - Erie Canal and Oswega Canal to Lake Ontario with a 6 feet
billbigdog at 2:38am 12.18.07
2/1740
I have a 2004 466 and the vaneer on the gangway steps is wearing through. Any idea where I can get
Stillraining at 7:11am 12.18.07
14/2198
My new boat has deck and mast hardware for a second head sail ( Staysail ). I like the Idea of redun
Dave K. at 9:15am 12.18.07
4/1052
I'm in the process of planning a trip to Lake Huron's North Channel with some friends. We've been ad
Dave C - pearsonowners.co at 9:06am 12.18.07
2/1268
We're Pearson owners, so I know we don't race too much! Okay, the 30 is very sleek, but most Pearso
Dave C - pearsonowners.co at 9:18am 12.18.07
1/1265
So, it's the 11th hour and I just KNOW someone out there is going, 'oh crap!' Here's my list of fun
Dave C - pearsonowners.co at 9:25am 12.18.07
17/6028
Everyone has a story... what's yours? Why a Pearson, of all the boats out there? For me, it was st
sailormanbigd at 9:49am 12.18.07
16/1381
First before anything...i know what happenned to act two and four? Just didn't label those posts. Th

Recent Replies

Where do I find this part?
dlochner at 1:53pm 04.08.21
If you want to remove that last little bit of water you will have to get a diaphragm pump. The typic
Winch removal
FastOlson at 1:47pm 04.08.21
Heat. Not too much, i.e. harmful to the gel coat, but hot to the touch. (!)
Shaft Zinc Placement   (1)
sail sfbay at 1:39pm 04.08.21
I install 2 zincs on the middle of the shaft, one about 8 inches forward of the strut and a second o
Late to the party - Raspberry Pi & OpenPlotter (Moitessier Hat)
kappykaplan at 1:39pm 04.08.21
? https://www.rooco.eu/products/moitessier-hat-2-raspberry-pi-openplotter-ais-receiver
Shaft Zinc Placement
Ralph Johnstone at 1:32pm 04.08.21
It's possible to obstruct the water flow through the cutlass bearing.
Hydrofoils future impact on sailing
TomY at 1:11pm 04.08.21
HILARIOUS!!!! I thought so, too. It was on Instagram and originated, I think, on Sailing Anarchy
Winch removal
Don S/V ILLusion at 12:54pm 04.08.21
What Justin described above is how we did it - leg power instead of a mallet. Very minimal cosmetic
Winch removal
dlochner at 12:25pm 04.08.21
Unfortunately there is no space. Not even for a razor knife. Like I said, I tried everything. Pulli
Winch removal
SEMPERAVANTI41 at 12:06pm 04.08.21
I did this exact winch conversion a few years ago. Forget the oscillating tools, chisels or pulling
Winch removal
thinwater at 11:52am 04.08.21
Tie a long line around the drum very tightly. Run the line up to the boom through a turning block a
Irwin 32 Compression Post Support
rogov at 11:35am 04.08.21
Thank you, that was one I had not found yet, but I'm fairly certain that my 32' Classic uses a woode
Beneteau Spare Parts Website
frietti at 11:26am 04.08.21
ASAP Supplies. I could not be more impressed, they really lived up to their name. Ordered the 29t
Boat Transportation Service Recommendation
Parsons at 11:26am 04.08.21
We used Boat Logistics (Boat Logistics - Moving Any Boat, Anytime) out of Michigan, and were very pl
Winch removal
souzag818 at 11:13am 04.08.21
Unfortunately there is no space. Not even for a razor knife. Like I said, I tried everything. Pulli
Winch removal
Mark Maulden at 10:57am 04.08.21
Tie a long line around the drum very tightly. Run the line up to the boom through a turning block an
Best place to list racing sails from a 35'?
sail sfbay at 10:52am 04.08.21
Welcome to the forum!! Only experience I have is advertising a new condition (used once) asymmetric
Boat Transportation Service Recommendation
sail sfbay at 10:43am 04.08.21
Try Sailors Moving Sailors. One forum member found out about this transport company on this site and
REPAIR: Mast Step & Chain Plates
rgranger at 9:55am 04.08.21
Your question really depends on tolerance... for me I'd compare the repair costs to the cost of an a

Copyright 1997-2024 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.