|
Ise the Bye
at 7:40pm 10.01.08
6/1743
I cannot find any other zincs on my boat other than the prop shaft. The Yanmar engine does not appea
|
||
|
Tom23352
at 7:03pm 10.01.08
2/2235
I'm a bit embarrased to admit I've been sailing the Mississippi sound since the early 90's but know
|
||
|
icos200
at 7:01pm 10.01.08
4/1137
High all. Not sure how to post a new subject. Just went through Ike, boat did'nt fare so well at th
|
||
|
Bob V
at 6:10pm 10.01.08
21/4608
OK, I understand the Sitezen Rating but what up with this Poster,s Reputation? My first question is
|
||
|
chuck
at 6:00pm 10.01.08
8/1986
hi everyone, new to the site. question for you all looking at a 1984 36 catalina that is for sale
|
||
|
Seattle Scott
at 5:26pm 10.01.08
2/1412
I was pulling into Brownsville marina last Saurday and there was Epiteme's stern sticking out with t
|
||
|
SoSound
at 5:05pm 10.01.08
13/1820
Would now be a good time for all of you "experienced" sailors to pass along your favorite tips on ma
|
||
|
Walter6016
at 5:00pm 10.01.08
14/1534
I have about 5 gallons of 2 stroke gas/oil mix left in a metal portable tank. Is it OK to save that
|
||
|
Nik
at 4:09pm 10.01.08
14/2933
Does anyone know where I can find the round spreader boots to fit 1" OD tubing; lie originally found
|
||
|
Tom
at 3:55pm 10.01.08
2/1229
into the site again!!! Phil, thanks for the help. Now all I need to do is figure out how to open the
|
||
|
Boat n Bus
at 2:24pm 10.01.08
10/2137
Can I connect the aligator clips from my solar trickle charger to the bus bar to charge the battery?
|
||
|
tom fitzpatrick
at 2:24pm 10.01.08
2/3264
1998 - Bavaria 47 ..rudder bearings replaced 2 yrs ago and wheel has now become v stiff to turn. An
|
||
|
capjules
at 12:53pm 10.01.08
0/1699
Hello, For anyone that is interested there is now a Fantsia 35 forum in the Brand Specific forums
|
||
|
walt
at 11:23am 10.01.08
4/3455
Im wondering why more racing type boats dont bother with battens in the jib sail? Hobie cat jibs typ
|
||
|
HukilauMike
at 10:51am 10.01.08
7/1971
I have been anxiously awaiting the return of the Photo Caption contest, and checking every day to se
|
||
|
need wind therapy
at 10:30am 10.01.08
1/2299
Hi, I have a 1973 29ft Ranger with a busted strut. any idea who made them originally? anyone had
|
||
|
Don Crowther
at 10:12am 10.01.08
11/2139
Hi Just getting things together for the winter and I was wondering how much antifreeze to buy? I w
|
||
|
arcflash
at 9:18am 10.01.08
2/1826
I have a cast iron keel on my 345. I bought it in Long Island and now in the great lakes but heading
|
||
|
Bob Pullen HC-33 1981
at 8:59am 10.01.08
6/1836
We are in the process of acquiring a new sailboat. I am an Alaskan resident. Would anyone have any
|
||
|
Glenn & Deb
at 8:54am 10.01.08
3/1343
A new gin pole for our 240 came in when we bought the boat. The top wire with loops went from port
|
|
New to sailing.... Looking for a first boat..
Kings Gambit at 8:08am 01.30.22 What would this mean... "GAIL WARNING is a shoal draft model with centerboard, allowing her to ven |
||
|
1987 Catalina 22 Outboard Spring Assist Lift Bracket
John Marrone at 8:04am 01.30.22 Thanks............ Only reason I am considering reattaching this outboard bracket is because of the |
||
|
1979 Hunter 33' Jack heights & count
V.Carter at 7:49am 01.30.22 Hello V Carter. :clap:Welcome aboard the SBO Forum. My 1979 H30C shoal draft takes 6, (plus one f |
||
|
Time to replace lifelines?
FastOlson at 7:48am 01.30.22 Like your standing rigging, replacement needs to be done on a regular basis. About 20 years is the m |
||
|
2013+ MH-40 Discussion
Gold70 at 7:20am 01.30.22 Has anyone had issues with cracks/crazing on the deck (specifically on a 2014 MH-40). Thanks in adva |
||
|
2013+ MH-40 Discussion
Gold70 at 7:18am 01.30.22 I have a 2018 MH40 (Hull 137). I have 3 friends on the Chesapeake that all have 2013 MH40's. We h |
||
|
Heat exchanger anode
SV At Last at 7:11am 01.30.22 The thinner gasket may reflect the progression in the advancement of science in generating new and |
||
|
Cracking around mast struts, major issue or no?
Crazy Dave Condon at 6:59am 01.30.22 Never heard back from the poster |
||
|
Hull
Crazy Dave Condon at 6:56am 01.30.22 Suggest too that the area be sanded to remove the gel coat and get the surface flat and smooth |
||
|
Time to replace lifelines?
dlochner at 6:45am 01.30.22 I used 1 x 19 3/16 type 316 bare wire, it is highly corrosion resistant. Flexibility, needed for |
||
|
How wide is the wing on the keel of a Hunter 26.5?? (1)
Orbweaver at 6:01am 01.30.22 Mine is 24.5" across, tip to tip. |
||
|
Heat exchanger anode
sailme88 at 5:50am 01.30.22 The thinner gasket may reflect the progression in the advancement of science in generating new and b |
||
|
1987 Catalina 22 Outboard Spring Assist Lift Bracket
Gene Neill at 5:31am 01.30.22 I've never had my motor mount off, so I'm just going by a mental picture. If there's a void between |
||
|
After the storm blows thru
shemandr at 4:34am 01.30.22 It's 36 degrees here in Southern Florida this morning. A cold front is a cold front everywhere on t |
||
|
Time to replace lifelines?
Joe at 3:45am 01.30.22 This will only allow inspection of the outer strands. The wire is constructed with a 7 strand core |