John
at 6:33pm 08.12.08
2/1036
I just returned from my boat where, among other things, I met Stu, who spent at least a couple of ho
|
||
blackcloud
at 5:51pm 08.12.08
1/946
The fuel guage on my Hunter 310 is pegged out below the empty mark. I have tried cleaning the elect
|
||
coralrec1
at 4:54pm 08.12.08
2/1437
I have a 1978 lancer here in oceanside ca and need to replace at least four of the opening/closing t
|
||
Capt. Kermie
at 2:12pm 08.12.08
0/688
I am not sure this is the right forum but I don't know where else. Here in the Pacific Northwest we
|
||
JoshGray
at 12:08pm 08.12.08
10/1091
Hope some of you guys with more experience can help me out there. I took my shoal keel 22 out to the
|
||
RS
at 10:50am 08.12.08
4/1393
I need a pic or two in regard to setting up the mainsail and boom, etc. any info/pics would be appr
|
||
hooyasailor
at 10:19am 08.12.08
4/2358
Hello, Folks, I have a new (OLD) boat! The trailer is shot (Rusted out) and I can't even move her ti
|
||
lancelot8602
at 9:43am 08.12.08
10/1999
I have inherited a 19' Oday Mariner, she is in pretty good shape. My wife and I have been learning
|
||
jdgrnt66
at 9:14am 08.12.08
1/1437
Hello all. I need to fill my CNG tanks and finding it hard to find refill stations in the tampa bay
|
||
tkanzler
at 8:36am 08.12.08
6/1073
The last post in the linked thread sums up both the problem and the reason why raising the switch wo
|
||
jim
at 8:11am 08.12.08
3/1004
How does one remove the compass to access the gear shifter linkage
|
||
Teak Refinishing (1)
Kjoe
at 7:02am 08.12.08
4/1116
I am in the process of refinishing the teak rubrails on my V-21. it was neglected for awhile so am
|
||
Maine Sail
at 6:09am 08.12.08
18/1687
Hi All, First, I know sailors are a cheap lot and I can be too but... Those of you who know me
|
||
BaySailerBill
at 5:47am 08.12.08
2/1036
Hi everyone, Last week I took a step that I hope was well placed. As some of you know I just fin
|
||
ChuckThomas
at 5:34am 08.12.08
1/1088
Did anyone hear about a catamaran in a wreck near the twin span?
|
||
sea_casper
at 5:09am 08.12.08
0/25
I have replaced the stock Rudder system including head plates and tiller, with an IdaSailor Kick up
|
||
Ralph18414
at 4:20am 08.12.08
15/1265
My heart goes out to the surviver.
|
||
Hermit Scott
at 10:50pm 08.11.08
4/1067
I pulled the engine in my Catalina 30 today. I pulled the head and most of the water passages were c
|
||
davidtre
at 8:11pm 08.11.08
2/1388
I have a 44AC and have been having trouble with line 1 circuit breaker continually tripping. Admited
|
||
Hoppy
at 7:51pm 08.11.08
2/1005
|
Need a clean SS cut
Justin_NSA at 7:07am 05.21.21 I hope you got some extra cutting wheels with that purchase? it came with a twin pack of extra whe |
||
hunter 22 swing keel
SeaTR at 7:04am 05.21.21 JeffJK, I replaced my 1981 H22 salvage boat's swing keel a couple of years ago with one made by Foss |
||
Retrieve lost end of topping lift?
dmax at 7:04am 05.21.21 I just rebuilt my boom (it's an Isomat, yours should be too). Internally mine contained two reefing |
||
Looking for cabinet and door latches for '97 Beneteau Oceanis 381
sail sfbay at 7:03am 05.21.21 Welcome to the forum!! Can you please photos of what you are looking to replace since there are so |
||
Need a clean SS cut
JamesG161 at 7:02am 05.21.21 Notice the spelling of "refrigeration" at the bottom Your family will be unhappy when you store th |
||
Bleeding air from fuel system Universal 5411 (2)
shank at 6:57am 05.21.21 Thanks for the response. Think this is the right one based on the diagram from the 5411 manual? |
||
Need a clean SS cut
Ron20324 at 6:42am 05.21.21 Had to share this one last thing. I received my new SS tubing cutter from Amazon. It looks very wel |
||
New to Catalina 18
lestersails at 6:26am 05.21.21 If anyone is from the area, what do you think about a wing keel in the Chesapeake? I was looking for |
||
How to "back" fittings used to route halyards to the cockpit?
MikeHoncho at 6:07am 05.21.21 Make plates out of starboard, one for the whole fixture. This will give you more than enough surface |
||
Swing keel Mac 25 (1)
GSmith116 at 6:05am 05.21.21 Was just inspecting my keel pivot bolt (push keel to one side of the well and use an inspection mirr |
||
Need a clean SS cut (1)
Justin_NSA at 5:41am 05.21.21 Had to share this one last thing. I received my new SS tubing cutter from Amazon. It looks very well |
||
Portable charger options
Maine Sail at 5:32am 05.21.21 hey Rodd- Do you carry the Victron IP65s model? Seems it superceded the IP65. Is there any major |
||
Retrieve lost end of topping lift?
Parsons at 5:28am 05.21.21 I'm with @shemandr - remove one bolt at the gooseneck, go to a outdoor staircase, make the boom vert |
||
Bleeding air from fuel system Universal 5411
Capt jgw at 5:23am 05.21.21 I never used that screw on my 5411, I used the bleed screw on the injection pump. On the fitting whe |
||
Housing market
tfox2069 at 5:15am 05.21.21 Same situation in Northern Virginia and the entire DC Metro and surrounding area. We've seen our ho |
||
Retrieve lost end of topping lift?
shemandr at 5:06am 05.21.21 I wouldn't spend a lot of time trying to retrieve it. I had a Selden boom but I'm not envisioning |
||
Have you checked your Standing Rigging for this season?
jssailem at 4:47am 05.21.21 Mother Nature can be cruel if you give her a chance. Hope you can get her back together before the s |