Serving sailors online since 1997
 
 

Recent Topics

chrisolavitch at 6:06pm 09.14.09
1/1781
After posting a previous question to the group-it appears my new jib was built with the wrong size l
Hermit Scott at 5:37pm 09.14.09
9/2319
I have 2 cheek blocks and 2 bullet blocks for 5/16" line. For now I have a cleat that I will mount o
tamas at 5:27pm 09.14.09
14/7289
I was going to start this process as a business about 15 years ago but never got around to it. Last
ranchu56 at 5:00pm 09.14.09
2/1429
I own a 1984 Hunter 34 and am looking to move lifeline gates from stern area to amidships. Does any
Denis Hodson at 4:25pm 09.14.09
1/1358
looking for a line drawing to install a head,holding tank ' plumbing in an O'day 26 (1984). I unders
hunter33owner at 4:19pm 09.14.09
2/1860
How can I clean the mesh seat covers in the cockpit? I have taken them off of the foam and need to c
hunter33owner at 4:07pm 09.14.09
0/1070
Was wondering what people are using to clean the mesh covers of the cock pit seats. I removed them f
chrisdaigle at 3:28pm 09.14.09
7/1861
I would like to know if it is unusual to not have some form of venting for the engine compartment. I
dwgifford at 2:19pm 09.14.09
8/2724
1978 H33 Cherubini - Want to run my main and spare main halyards from the mast back to the cockpit f
dserrell at 1:18pm 09.14.09
10/2804
1 1
knotaclew2 at 1:10pm 09.14.09
4/2638
Does anyonr know the best place to get a new hatch for my 1988 28.5. all I need is the top portion a
texasprinter at 12:40pm 09.14.09
1/2093
My original Universal 5411 had a cracked block from salt buildup so I found another 5411 to replace
tgrass462 at 12:30pm 09.14.09
10/3056
It's getting that time of year - at least in a couple of months ... to cover your boats through the
Rxman47 at 10:40am 09.14.09
7/4921
Peggy, Where can I find directions for re-commishioning a plastic water tank? I have searched on the
Steve22124 at 10:33am 09.14.09
3/2097
I want to install a transducer (hopefully in hull). Is the hull in a 1978 H27 solid fibreglass (I h
Donald Farquharson at 10:00am 09.14.09
3/1633
I want to let my fellow Hunter 35.5 owners know that thanks to your advice I was able to stop the ha
jackhartjr at 9:43am 09.14.09
1/1319
Hi folks, was wondering the differences from the Oday 32 in the Ketch or Sloop versions. Would the K
bayrat at 9:19am 09.14.09
0/960
A bad blow left my rudder and tiller and the bottom of the bay. Does anyone have a used one they wou
BobM at 9:12am 09.14.09
S2
1/1238
Got out for a sail last night. 10+ knots blowing straight out of Winthrop Harbor. I set her up win
Fly Away at 8:48am 09.14.09
1/2007
Is there a cover made for the emergency tiller? That thing is constantly banging my legs when chang

Recent Replies

Do You Know A Good Broker?
jssailem at 6:15am 03.23.22
Boats here in the PacificNW are priced a bit higher that most other regions. As @dlochner stated the
Icom m802   (1)
jssailem at 6:04am 03.23.22
It uses a : GPS interface NMEA 0183 version 3.01 Or you can fill the GPS connector on the back with
Hunter 34 (1984) Bimini from sailboatowners.com
RoyS at 5:56am 03.23.22
IMHO if you have the ability to dictate design, it is best to extend the back of the bimini over the
Do You Know A Good Broker?
Prairie Virgin Sailor at 5:28am 03.23.22
Thanks for the feedback. Much appreciated.
CENTERBOARD HELP   (1)
twodzusfittings at 5:11am 03.23.22
203703 Centerboard finished. Cavity wall in the Keel repaired as needed. All ready for a new cable
ICW actual state "of affairs" conditions
dlochner at 5:00am 03.23.22
There are lots of boats in Florida. Look closer to home.
Hunter 34 (1984) Bimini from sailboatowners.com
sailermaned at 4:57am 03.23.22
I purchased one from them for my 31 which will be basically the same, and it does not go past the st
1985 Pearson 303
dlochner at 4:57am 03.23.22
The going shop rates for boat yards is $125-150 per hour. If all goes well you have 2-3 days of labo
Freezer repair, 2015 Oceanis 48
Roger F at 4:55am 03.23.22
It opened up fine! I will reach out or if need be coordinate with a local marine service repair g
Semco Teak Sealer - progress photos
BigEasy at 3:07am 03.23.22
I used Semco on other wood on the boat and have photos of that if folks are interested. Look
Starting over from scratch
BigEasy at 2:50am 03.23.22
Is that the shift mechanism that was originally used with your current motor? If yes, does that sh
Wooden strip for Stern Rail Seats
Ken13559 at 2:26am 03.23.22
Thanks all. I'll have a word with local timber store. Will hunt for plast-teak as well but not going
Scared myself - broken forestay
nightowle at 12:52am 03.23.22
Indeed, scary stuff. You handled it well. All the while looking searchingly at your first mate for
Freezer repair, 2015 Oceanis 48   (1)
HaroldW at 12:19am 03.23.22
I was wrong about it being flat. I got the flat one for a different job. This is the parts breakdown
Hatch handle
Mark Maulden at 9:25pm 03.22.22
This is going to need a pic. I'm wondering if the two pieces of teak are guides for sliding?
Catalina 30 Table/hardware
pipedream at 8:43pm 03.22.22
My boat is a 1973, and many bits and pieces have been out of production for a long time. Lucky you l
1985 Pearson 303
Tally Ho at 7:59pm 03.22.22

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.