|
Raftco
at 5:53pm 10.16.09
13/6394
I'm trying to research how people deal with their outboard engine and fuel tanks? I'd prefer to us
|
||
|
Sans Souci
at 4:05pm 10.16.09
7/3035
I have a 2003 Hunter 356. During my first haul out, the keel had blistering. The thought was it had
|
||
|
austinswalk
at 2:51pm 10.16.09
16/5985
hi, new to site and getting ready to order new 309. any advice on must haves and really don't need a
|
||
|
jcmaui
at 2:32pm 10.16.09
2/1698
the water tank under the v-berth is a pain because you have to take the whole v-berth apart every ti
|
||
|
Saltymare
at 1:49pm 10.16.09
1/1194
The plexiglass complanionway slide is badly cracked on my H34 (83) and the epoxy repair isnt holding
|
||
|
b69lotus
at 1:22pm 10.16.09
1/2666
I have a 1983 C30 with external halyards. Does anyone have any suggestions for running my external m
|
||
|
DesertSailor07
at 1:11pm 10.16.09
4/1685
Land locked as I am, a sailor at heart. Looking for a 25-26' trailer-able late 80s-late90s. I thin
|
||
|
Salty
at 1:05pm 10.16.09
17/12159
I am planning on circumnavigating Long Island in 2010, leaving from Mt Sinai (East of port Jeff) goi
|
||
|
bffatcat
at 11:53am 10.16.09
7/5757
Any opinions or comments about the structural integrity and durability of todays newer light weight
|
||
|
BreakAway
at 11:40am 10.16.09
2/1900
I have a First 310 with an 18hp 2002 Volvo Penta engine. When running for some distance (1 hour or m
|
||
|
Barry1957
at 9:57am 10.16.09
3/8146
Does anyone have a comment on which of the two products of "hands-free" stabilizing of the tiller pr
|
||
|
digitek718
at 9:14am 10.16.09
7/1738
Hey..this site is awesome..looks like I am going to get some great ideas for mods and maintenance of
|
||
|
digitek718
at 8:31am 10.16.09
3/1304
I just bought my first sailboat about a week ago..an oday 25...I went out sailing a couple of times
|
||
|
beachkoma
at 8:06am 10.16.09
6/2752
Will a Sevylor Electric Trolling Motor (18 lbs thrust) be enough to power my 1976 Widgeon in a salt
|
||
|
Mark3755
at 7:05am 10.16.09
4/1915
My boat is about an hour away, so I was hoping to get some help to save me a 2 hour round trip for
|
||
|
Raftco
at 5:53am 10.16.09
7/3108
I have a through hull brass or bronze fitting that is directly below the sink in the galley on my O'
|
||
|
Zoey
at 4:37am 10.16.09
26/5370
If sailboats already have antifoul paint (Baltoplate) why do owners they have the undersides scrubbe
|
||
|
pkdailey4
at 1:11am 10.16.09
8/3397
Whats the best paint that's legal in California waters ? I'm using Interlux Ultra now but I don't kn
|
||
|
awoody
at 11:20pm 10.15.09
3/1802
I have been receiving a lot of good information from the forum. However, I must not be using it cor
|
||
|
sol y mar
at 8:04pm 10.15.09
6/4185
I just purchased a 1989 catalina 30 with the M25 diesel. I want to replace both the fuel line and th
|
|
H240 Pulpit drawing (2)
sail sfbay at 10:35am 05.04.22 Suggest looking for images of all the angles like the ones of a 240 below and measure the forward an |
||
|
Edson wheel adjustment!
Growl at 10:07am 05.04.22 Like, Two turns deport and two turns to starboard when I forget I only have half a wheel for a port |
||
|
Edson wheel adjustment!
jssailem at 10:07am 05.04.22 Look over the stern and check that the rudder is in inline with the boat keel. When it is inline the |
||
|
Edson wheel adjustment!
Richard19068 at 10:00am 05.04.22 Right. That's 3-1/2 total. Is that normal or did you in the past get 5 or 6 or 7 or something else |
||
|
Edson wheel adjustment!
Growl at 9:57am 05.04.22 Hi, I only get half a turn to port then 3+ to starboard! |
||
|
Edson wheel adjustment!
Richard19068 at 9:55am 05.04.22 How many total turns do you normally have from "lock to lock"? If normally 3-1/2 turns total then pe |
||
|
Ammeter replacement questions (1)
jonelli at 9:54am 05.04.22 FWIW, here's my main re-wired battery setup: emory wire. They're always yellow. That black wire on B |
||
|
Headsail sizes
sail sfbay at 9:35am 05.04.22 Same question came up on this thread: Tacking a Genoa? | SailNet Community |
||
|
How do I get to this bolt?
Len Ingalls at 9:25am 05.04.22 You could use U-joint socket of correct size. U-joint allen head sockets are also available. Cheers/ |
||
|
Hunter 460/466 Spinnaker Pole
sail sfbay at 9:18am 05.04.22 Suggest contacting Forespar and Selden for a size and material of construction recommendation and pr |
||
|
Motor decision for my Hunter 240
isaksp00 at 8:57am 05.04.22 Don't know your motor, I have a Honda 8. Is it unreliable mainly at idle and low rpm, but once you r |
||
|
Edson wheel adjustment!
Sailfanatic at 8:56am 05.04.22 If this is a new development, my suspicion is that there is some obstacle inhibiting the steering q |
||
|
Seeking advice from any chemists, bottom paint related
Barnacle Bill at 8:51am 05.04.22 Why wouldn't you call ePaint for a solution? |
||
|
Spin vs whisker pole
Barnacle Bill at 8:49am 05.04.22 Spinnaker (spelled that way) are, as someone mentioned, a fixed length - that being the j dimension |