Serving sailors online since 1997
 
 

Recent Topics

moose at 6:16pm 11.13.09
3/1355
mykeel is makeing 1 inch of water is that nomal .
kczach1 at 6:16pm 11.13.09
3/1844
Hi all, I have a Catalina 270 and am going to be re-painting the bottom with new anti-fouling pai
nofd843 at 4:02pm 11.13.09
0/1502
I am in the process of purchasing an inflatable tender and trying to find a way to store the motor o
Small sloop at 12:10pm 11.13.09
5/3232
Has anyone had diesel fuel collect under the tank? After several months away from the boat, I ha
butchrobbins at 11:55am 11.13.09
12/2147
A filmy scum is builing up on my sinks (kitchen and head). I use 409 to clean them, but not doing t
ryanmohr at 11:18am 11.13.09
21/3458
I was doing a preliminary survey on a Cal 27 yesterday and saw these funny looking splits in the mas
blink at 10:36am 11.13.09
0/1097
Looking for a first 235 in very good condition
ksetchfield at 10:18am 11.13.09
5/1433
Still trying to get a trailer for my hunter 22. I've been trying to find out how far below the hull
myerssl at 9:49am 11.13.09
4/2741
Man it's been a blast this year. As mentioned in earlier posts, I purchased the boat last December,
Garrett7m-FL at 9:33am 11.13.09
28/16949
Is it unreasonable to think that I would want to step the mast on a C22 (or similar sized boat) in t
sailor5017 at 8:09am 11.13.09
2/1785
has anyone used Linux to run older nobeltec navigation software?
captainmitch at 7:50am 11.13.09
1/2743
Does anyone have any ideas on the selling of a new condition main sail? I have a batten main by Mac
BarryL at 7:42am 11.13.09
1/1558
Hello, I currently own an O'day 35 and I am thinking of boat with better sailing performance. I rac
Quoddy at 6:38am 11.13.09
5/1948
We have a shallow draft, centerboard, light displacement, beam carried aft, boat. Am I right in assu
lycaman at 9:41pm 11.12.09
4/4781
I need to replace one rear engine mount, 88 Catalina 30. Can anyone advise what are the key steps to
tgo918 at 7:13pm 11.12.09
8/2096
I'm planing to move to the sea. Is it better to buy a fresh water boat than one in salt water
Salish Sea Cruiser at 5:18pm 11.12.09
6/1770
For preventive maintenance and at the recommendation of a surveyor, I am going to replace most of th
nofd843 at 4:51pm 11.12.09
2/2312
I have a Hunter 240 and I have a couple of questions. The first question is how do you get the lo
CharlieCobra at 4:44pm 11.12.09
7/1456
I cut a section of the C-Flex away to pull a section of planking and get to the bad spot for further
Sailor Sue at 1:35pm 11.12.09
9/1903
I'm trying to hook up a USB GPS (Globalsat BU-353) to a laptop for charting. The instructions say to

Recent Replies

Desperate leakinhg
Halvern at 8:27pm 04.26.22
Friend thinks possible that an extra low tide could have set her on the bottom with too much weight
Paddlewheel Protection
Stu Jackson at 8:24pm 04.26.22
Years ago I asked one of the yard guys for a small amount of regular bottom paint in a plastic cup.
New Catalina 30 Owner
mikeracca at 8:21pm 04.26.22
Ok, so I was thinking about my dilemma. I am missing the large nut that would normally be used to a
Oceanus 400 transducer location?
Rattlenebang at 7:59pm 04.26.22
Thanks everyone. I carved out a hole in the floor pan 18" away from the centreline and that seemed t
New Catalina 30 Owner   (4)
mikeracca at 7:53pm 04.26.22
So I would have never thought, at the time I was learning this, that a skill I picked up restoring o
So I found this bolt ...   (2)
rpwillia at 7:17pm 04.26.22
Bazinga! Joe White gets the Gold Star. Turns out it is one of two under the bracket that the port mo
Desperate leakinhg
Hayden Watson at 7:14pm 04.26.22
I would like to see some photos of the crack in the hull.
Desperate leakinhg
Hayden Watson at 7:03pm 04.26.22
Just curious. How many of you have ever before heard of a hull being cracked by over tightened stan
Paddlewheel Protection
Blitz at 6:48pm 04.26.22
The paint I used on my AIRMAR speed transducer and old Datamarine depth transducer has been the MDR
O'Day 25 Shoal Draft Centerboard Water Leak
jibes138 at 6:32pm 04.26.22
Use saran wrap to hold the epoxy in place with duct tape or painters tape to hold the edges of the s
Desperate leakinhg
Richard19068 at 6:07pm 04.26.22
Just curious. How many of you have ever before heard of a hull being cracked by over tightened stand
Two-battery LiFePo4 system?
AlanSD at 5:39pm 04.26.22
Oh, thanks, I should look more closely. Can you say what Victronics components I'd need to do this
Desperate leakinhg
jviss at 5:33pm 04.26.22
Hunter Passage 42 Holding Tank Sending Unit
eianm at 5:23pm 04.26.22
removing that foam is indeed easy- i used an ordinary wood saw- completed in minutes- after i fitted
Desperate leakinhg
Davidasailor26 at 5:20pm 04.26.22
Did you notice he said the hull was broken by too-tight shrouds already? :) The hull was broken,
Desperate leakinhg
Tally Ho at 5:17pm 04.26.22
Did you notice he said the hull was broken by too-tight shrouds already? :) I did, but I was thin
Desperate leakinhg
jviss at 5:14pm 04.26.22
Desperate leakinhg
Tally Ho at 5:09pm 04.26.22
Best bet would be to try and borrow a Loos gauge (note that there a few sizes depending on wire si

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.