Serving sailors online since 1997
 
 

Recent Topics

Scott B at 7:11am 01.24.22
19/2907
I installed a new Trident 101 waste hose roughly 7-8 yrs. ago. When I first installed it, there was
ivieto at 6:41am 01.24.22
3/697
ivieto at 6:39am 01.24.22
1/676
Rudder,   (1)
Rodsails at 7:25pm 01.23.22
3/923
Has anyone removed the skin to inspect the rudder stock? We took a hard hit last summer then was gr
Light air at 4:34pm 01.23.22
3/671
I was out today with my new battery and it turned out to be the starter as the problem. Meanwhile,
Rick D at 2:48pm 01.23.22
19/1650
I have a powered halyard winch on my 1994 Hunter 40.5. It has started tripping the breaker under a h
Andiamo 34 at 1:49pm 01.23.22
2/593
I have a 34' Hunter Legend and the insulation on the wiring for the anchor and running tri light has
Brian D at 12:59pm 01.23.22
18/2885
With the price of real estate and houses sky rocketing, would you think that this is a seller's or b
Ken13559 at 10:54am 01.23.22
6/1636
If I were to replace my Raymarine ST40 Depth transducer, can I cut the existing cable and join the n
sailing gal at 7:25am 01.23.22
9/1183
Anyone if 410 the clutch mounting location has an aluminum backing plate mounted in? I need to add o
djletin at 7:01am 01.23.22
4/1090
I have a new-to-me 2003 Catalina 18 that I purchased late fall 2021 and have not sailed yet. The po
Halvern at 7:53pm 01.22.22
S2
7/1724
Re-open an old thread. Does anyone have a source for a v-berth headliner for an 11A, or instructions
"Hawkeye"   (3)
Simon Sexton at 7:05pm 01.22.22
7/2034
Weasel at 5:38pm 01.22.22
15/1262
Lot of good common-sense info here. Don't know where it came from but I thought I would share with o
Rialto at 2:14pm 01.22.22
1/788
Hi Is there anyone currently on their Beneteau OC 423 (2006) that could measure their doors for me?
Nachismo at 11:39am 01.22.22
1/610
Ron Allen at 8:48am 01.22.22
8/3101
Hi All, Looking for the correct size and length for the control lines for the main sheet and boom. T
CaptainRed at 7:14am 01.22.22
8/1370
Looking to replace my 28" Destroyer wheel. Existing Edson pedestal on my 1986 Catalina 30 Mark 1 TR
What is it?   (3)
justsomeguy at 6:26am 01.22.22
6/922
Dock neighbor went out for a shakedown and found this on the deck afterwards. I thought perhaps it w
All U Get at 5:47am 01.22.22
3/792

Recent Replies

Diesel engine as generator question?
kloudie1 at 12:33pm 03.26.25
@ Foswick: Since diesels need compression heat to ignite the fuel, it has to have a full charge of a
Bowsprit Protection from Chain
colemj at 12:14pm 03.26.25
Well, it does until you crank on the manual override. I don't know any other way to safely raise th
Diesel engine as generator question?
colemj at 12:00pm 03.26.25
Interesting, this brings up a question I have been thinking about for some time now. At some point
Any Nissan/Tuhatsu experts out there?
azambella at 11:52am 03.26.25
Thanks. It's really small block so I don't think it will be hard to find. TZ
Diesel engine as generator question?
colemj at 11:41am 03.26.25
You missed Calder's point. The point is non-sensical. Yes, if you are running your engine for p
Galley table ideas
dmax at 11:39am 03.26.25
As Paul says, 1/2" is good - use a high quality, exterior grade plywood. Marine if you want to spend
Any Nissan/Tuhatsu experts out there?   (1)
Richard19068 at 11:31am 03.26.25
I have an old Nissan 2 cycle outboard motor and want to identify it. The "TAG" has worn off so the
Adding eye straps to C320 toe rail
rickr104 at 11:07am 03.26.25
Hah! Totally agree - The drilling was making me nervous. I slept on it and decided to use 1/2" PVC c
Diesel engine as generator question?
Foswick at 11:06am 03.26.25
You missed Calder's point. I don't think the point was lost. I think, though, that the assertion th
What the heck are these compression fittings?!
sailcapt340 at 10:49am 03.26.25
Check Fresh Water Systems Co. I agree with Mark, why not just replace the fittings with updated con
Diesel engine as generator question?
Foswick at 10:43am 03.26.25
Some diesel notes: ... That is a really great answer that actually gets to the question. Of course,
DIY Remote Monitoring System
SV Temenos at 10:37am 03.26.25
If you have the Cerbo and a way to stay connected to the internet (cellular wifi or Starlink) check
Bowsprit Protection from Chain
Foswick at 10:27am 03.26.25
Hydraulic magnetic breakers are a thing, and use a different mechanism than thermal breakers. Eithe
Galley table ideas
PaulK at 10:08am 03.26.25
Problems with water absorption often come when people aren't careful with their epoxy coating, or if
Folding Cart
SteveHughessails at 10:05am 03.26.25
Folding Cart   (1)
Foswick at 10:02am 03.26.25
230520
Galley table ideas
fred1diver at 9:52am 03.26.25
What thickness plywood would you recommend? Having a frame on the sides will add stability and stren
Diesel engine as generator question?
dlochner at 9:26am 03.26.25
Thanks. Looks like some good articles. John Harres is an excellent resource, certainly worth a c
Galley table ideas
dmax at 8:57am 03.26.25
Sounds like bad formica - weird. I couldn't find anyone that would sell me raw Corian when I looked,

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.