Serving sailors online since 1997
 
 

Recent Topics

Banooma at 7:51am 03.08.10
3/1550
The mechanism in the arm that holds my C28 mkII icebox lid open, then when lifted a little releases
Ariel at 7:33am 03.08.10
42/6133
I just read on another forum that in Maryland and New Jersey, when the CG stops a boat for an inspec
Kenlee at 7:32am 03.08.10
0/1041
My 1978 O'day 30 has a single lever engine control for the Yanmar engine. It's mounted near the dec
ITMaster at 7:22am 03.08.10
2/1352
I hit the jackpot recently. Some friends called me mid January from California and asked if I want
Chuzzlewit at 7:22am 03.08.10
0/1306
draws 5" less than the rudder. Is this normal and will drying against a harbour wall damage the rudd
Chuzzlewit at 7:16am 03.08.10
4/1686
which draws about 4'6". The rudder draws 4'11".Has the boat been modified in the past and willl the
Bum at 6:54am 03.08.10
2/2817
Hello All, My wife and I are cruising again in the Bahamas on our Beneteau 331 w/swing keel along wi
Jared20459 at 4:44am 03.08.10
9/2709
I am refinishing our cabin sole of our Hunter 34. The old one has some moisture problems, so I had
Bob Poff at 3:38am 03.08.10
6/1392
Yesterday I finally had enough of the huge glob of black duct tape and stuphe covering the aft end o
markstv at 10:16pm 03.07.10
S2
4/1667
Thanks for the input on the prop.I am looking at buying a jib or genoa for my 8.0cc any suggestions
captnemojr at 10:14pm 03.07.10
2/1455
I know that there has been lots of discussion on mooring in salt water and keel up or down. well i j
acceri at 10:06pm 03.07.10
3/96
I just got a 1974 10m. Looking for what needs to be done..found a lot.. But I cannot find toilet se
nick at 9:49pm 03.07.10
3/1834
I helped sail a 43ft Cat back from the Whiitsundays to Brisbane (around 600 miles) last month and on
26macsailer at 8:09pm 03.07.10
10/1880
Im needing to replace the fiberglass trim (u-shape) piece that goes around the rear, top portion of
larry100 at 7:29pm 03.07.10
2/1585
Just had a new cutlas bearing installed on my 1988 catalina 30. Immediately started hearing a high p
MARKMOON at 7:01pm 03.07.10
5/2828
I just bought a 85 hunter 22 i have been looking for awhile for a boat in my price range so i found
foolproof at 6:54pm 03.07.10
6/3868
Hello all: I am interested in rebedding the Genny rails on my C30 while I'm rehabbing everything e
jwieneck at 6:37pm 03.07.10
13/1882
Looks like we are really going to go south with our boat this fall. I am trying to decide between t
Gruby at 6:26pm 03.07.10
1/1908
I have water leak only during high wind sailing (boat healing > 30) comming possibly from leaky rub
jdgrnt66 at 6:07pm 03.07.10
7/2244
Hey guys and gals. We want to switch from a 2 bladed prop to a 3 blade prop for cruising. Anybody

Recent Replies

2002 Hunter 260 chain and cable maintenance
Davidasailor26 at 12:58pm 04.25.22
What kind of noise (creaking, clunking, squeaking, etc)? Generally there is a way to access the chai
Tahatsu 6hp Sailpro for my Hunter 240   (1)
ingramsail at 12:55pm 04.25.22
I used a couple prices of pvc pipe and hose clamps
Tahatsu 6hp Sailpro for my Hunter 240
Rick Webb at 12:43pm 04.25.22
Got a Mercury 9.9 with the twist throttle, but still need a long extension to see where I am going
Tahatsu 6hp Sailpro for my Hunter 240
Dolphin55 at 12:40pm 04.25.22
The larger small Mercury outboards have a "Grip Shift" throttle. Twist the throttle one way for for
Annual WAxing ROutine
tfox2069 at 12:39pm 04.25.22
+1 on Mainesail's definitive guide. I did it for the first time this year on the hull and got good
C34 deck flex over sliding companionway top
JoeWhite at 12:38pm 04.25.22
My Mark II is keel stepped.
Autohelm Wheel Clamp Replacement 1989 Mark II
kappykaplan at 11:40am 04.25.22
I know it looks a little cheesy Very nice out-of-the-box solution! :beer:
Tahatsu 6hp Sailpro for my Hunter 240
rgranger at 11:33am 04.25.22
I'd try it as is and see if you like it before spending money on add-ons. I had no trouble with min
Autohelm Wheel Clamp Replacement 1989 Mark II   (1)
reuabyor at 11:32am 04.25.22
I know it looks a little cheesy, but I got the parts from Lowes and made some. I had the same proble
C34 deck flex over sliding companionway top
Stu Jackson at 10:54am 04.25.22
There is a turnbuckle ( on keel stepped) All the Mark II boats are deck stepped.
Annual WAxing ROutine   (1)
Scott B at 10:33am 04.25.22
This year will be the 15th season we've had the boat. I've been following the advise from Maine Sai
Docking with a loop
cymeyer at 10:32am 04.25.22
There was a recent thread talking about docking methods, and I commented on my loop method of docki
Mooring ball pickup - single handed
capta at 10:17am 04.25.22
What? You pick up and attach your boat to a mooring? Unheard of! We just pick one of the several "bo
Needing a new motor for my Catalina 22
Jacktar at 10:06am 04.25.22
Ditto love mine
Annual WAxing ROutine
AndyL at 9:59am 04.25.22
We have a similar boat. I'm not an expert but came up with this strategy after doing some reading a
New Catalina 30 Owner
mikeracca at 9:11am 04.25.22
Have you made cockpit cushions?
jeepbluetj at 9:02am 04.25.22
On the oversize, I'd go around 1/2" (~1cm) or a bit more. It really depends on the foam and the fabr
Build a Better Boat Hook?
jviss at 9:00am 04.25.22
Watch Deadliest Catch for the proper way of throwing these things. Most of them use an overhand "n

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.