jumbyway
at 3:05pm 07.01.10
1/1475
The Volvo D55 on our Beneteau 423 only has a tack and oil pressure guage, along with temp, alternato
|
||
howard
at 2:38pm 07.01.10
8/2083
I have a yamaha 8hp two cycle. The carb has been rebuilt within the year but i do not use it enough.
|
||
malyea
at 2:01pm 07.01.10
6/1749
...most of the time. I don't like the cluttered look they present when they're folded back out of
|
||
Roger Long
at 1:52pm 07.01.10
11/2602
Seeing MaineSail's beautiful photo took me back to my days as father of young children and this item
|
||
tpzahm
at 1:35pm 07.01.10
1/1289
Has anyone raced their Hunter 146 in a handicapped race? If so, what was the handicap? (PHRF, Port
|
||
JonnyQuest
at 1:26pm 07.01.10
1/2048
My stanchions for the life lines are pretty are anchored pretty weakly, and any lateral pressure cau
|
||
LarryH
at 1:24pm 07.01.10
3/1432
Has anyone replaced their bowlight? I am wondering where to find a replacement. I also need to repac
|
||
Maine Sail
at 1:06pm 07.01.10
1/3508
The new Sensibulb, that just began shipping last week, is nearly 40% brighter than the ones I tested
|
||
stx203
at 12:26pm 07.01.10
1/3347
I snapped a section of my Plastimo rollerfurler 608-T and need a replacement. Does anyone know of a
|
||
Sam Salter
at 10:57am 07.01.10
2/1639
Looking for info: A customer has given me a 110 furling jib off a 2004/6 Catalina 250 (swing keel)
|
||
elk
at 8:49am 07.01.10
6/1945
We have a 2006 350 and have always had problems fitting the screens that came with the side ports. T
|
||
ctaylor
at 8:38am 07.01.10
2/1303
I am trying to find the year of my boat. The serial is XDYG2318M79J. Any help would be appreciated.
|
||
ffaubert
at 7:15am 07.01.10
31/9604
Hi, Has anyone figured out a way to hide the gas tank on a Mac 25'? I searched the site and fo
|
||
ffaubert
at 7:08am 07.01.10
7/2495
Hi, How do you hook up the galley to supply fresh water and remove gray water? I checked Sum's
|
||
ffaubert
at 6:55am 07.01.10
2/1292
Hi, I was wondering if anyone has drilled limber holes from the inside liner to the bilge area in
|
||
duality
at 5:32am 07.01.10
7/1973
ok, good news is i got the clog out by taking the pump out hose to the joker valve elbow. it sucked
|
||
Bill Jones
at 4:31am 07.01.10
10/2811
I've checked out a couple of websites for cockpit cushions for our 23.5 and am suffering a bit of st
|
||
lizardosversoza
at 10:57pm 06.30.10
4/2121
I have a 1980 Macgregor 25 and I am wondering if there is a shop or somebody who could install a pen
|
||
Philip_Oceanis 361
at 10:56pm 06.30.10
1/1377
I am sure that most of you have somewhere in the sea water circuit a vented loop (anti sympon loop).
|
||
docker1
at 9:49pm 06.30.10
0/1320
had trouble installing keel board. keel board came separate and is original. there is a pin with a p
|
Hunter 31-2 mainsheet routing question (easy one)
StephenD at 10:14pm 03.23.22 Thank you. Some great ideas, particularly about routing both ends of the mainstream down the arch. H |
||
ICW actual state "of affairs" conditions
SFS at 9:39pm 03.23.22 .... it really doesn't make sense to look for a 40-year old boat in Maine when you live in Florida. |
||
I'm Tweaking My Battery Banks and Need Advice
Hayden Watson at 9:38pm 03.23.22 The Only time we use an isolator diode= (NEVER) or FET= (for LiFePo4 installs). We use DC to DC the |
||
Black rubber stuff in bilge?
mikeracca at 9:30pm 03.23.22 Looks like bilge sludge to me. But I would wonder not only does it smell bad but is the water in the |
||
1977 O'Day 27. 1st Sailboat ever.
JRacer at 9:07pm 03.23.22 Thank you. Yes, atomic 4 rebuilt with 500 hours. She purrs. I'm excited to learn the ropes Tho |
||
1977 O'Day 27. 1st Sailboat ever.
Hayden Watson at 9:06pm 03.23.22 In Everett, you have a very good sailing resource in the Milltown Sailing Club. I few nights of cre |
||
Hatch handle (1)
Mark Maulden at 7:47pm 03.23.22 The teak pieces run across, 90 degrees to the slider sides. Almost like two long washers sandwichin |
||
Fiberglass repair
BigEasy at 7:25pm 03.23.22 Agree with David that the rudder is failing from a previous repair. I would get some 36 or 80 grit |
||
ICW actual state "of affairs" conditions
Scott T-Bird at 7:25pm 03.23.22 Need your advise on this... ASAP This is part of the ad: Mechanical "Yanmar marine diesel engine ne |
||
Starting over from scratch
BigEasy at 7:22pm 03.23.22 Do you recommend I go back with something like a 9.9 Mercury, or do you think it would handle a 15 |
||