dkinzer
at 7:08pm 10.29.21
11/990
Well, we closed last week on a 2007 Hunter 41 DS. We've been exploring all of the nooks an crannies
|
||
Captain Larry-DH
at 6:47pm 10.29.21
6/856
|
||
Timbo33
at 4:47pm 10.29.21
14/1628
I have 1976 catalina Tall rig that does not leak but bolts are pretty rusted. Trying to decide which
|
||
chriscampbell
at 3:00pm 10.29.21
21/2760
I'm going to add a small solar panel system to keep my battery charged. I want it to be small and mo
|
||
All U Get
at 12:49pm 10.29.21
13/1873
Another question, What do you use for binoculars and portable radios to get the sticky feeling off
|
||
JWS
at 12:17pm 10.29.21
2/818
My kids broke the mounting pin out of the bottom of the case. There is no way to repair it, I can't
|
||
All U Get
at 4:10am 10.29.21
30/2686
|
||
Trick
at 7:28pm 10.28.21
7/1455
I just bought my first sail boat. Having trouble with what dia. Lines and sheets to buy. Any help wo
|
||
Guy Erdman
at 5:08pm 10.28.21
10/2092
I have owned my precious Ericson 27 for 10 years and thoroughly enjoyed sailing her. Since we use he
|
||
bradm
at 3:32pm 10.28.21
5/1283
Proud new owner of hull #9 here. First boat, first post. My mainsail doesn't furl/unfurl as easily
|
||
ChicagoWill
at 3:08pm 10.28.21
4/1367
Assistance please. I have tracked the history of my boat somewhat and yet keep getting some differen
|
||
Hayden Watson
at 12:35pm 10.28.21
17/1936
I always hear that I should wire tie the set screw for prop shaft flange but none of the set screws
|
||
Bluenose
at 10:50am 10.28.21
2/1184
Hello all, a pre-sale survey says the port bulkhead needs to be completely replaced. I am handy at b
|
||
Bluenose
at 10:46am 10.28.21
0/11
Hi all, I am looking at a Bristol 24 that needs the port bulkhead replaced. Access is fairly easy, b
|
||
SVFreedom
at 7:51pm 10.27.21
15/3249
I have seen some of Peggy's posts on macerators jabsco vs raritan - just replaced my most difficult
|
||
SkookumZac
at 6:13pm 10.27.21
15/2413
Hi all, I am about to cut a hole in my mast and before I make an expensive mistake I'd like to run
|
||
Thaelia
at 5:15pm 10.27.21
4/460
Hi, has anybody got a recommendation for a good surveyor in east Florida. The boat is in Fort Pierce
|
||
John Marrone
at 2:27pm 10.27.21
10/1579
Okay....I'm still learning all the "Ropes" here. Hauling in the Anchor with this Pre-Spliced 3-Brade
|
||
jmce1587
at 11:43am 10.27.21
18/4259
|
||
Project_Mayhem
at 11:23am 10.27.21
19/2008
I went to purchase a new fuel filter/separator and noticed there was two different types available f
|
Installing a EV-100 Cable question
jviss at 6:41am 07.09.24 So the 5m cable could be plugged into the 5 way and the data from the p70 would transfer to the ACU |
||
Installing a EV-100 Cable question
Don Crowther at 6:36am 07.09.24 John & BrianQ That attachment you sent cleared up alot for me Thanks Greg and Ward H Thanks for you |
||
What are these tracks used for?
Crazy Dave Condon at 6:32am 07.09.24 @CaptnEdarli how about telling us what sail inventory you have before any more responses? |
||
Installing a EV-100 Cable question
jviss at 6:27am 07.09.24 The resistors at the ends of the N2k bus serve two essential purposes. First, they provide the inte |
||
What are these tracks used for?
Joe at 6:04am 07.09.24 Thought the pulley was the round part inside the block That's the sheave. I think using the term |
||
Installing a EV-100 Cable question
Ward H at 5:57am 07.09.24 So the white goes from the p70 to the T and then the blue will go to the 5 way connector block. Wh |
||
Stuck seacock question
jviss at 5:52am 07.09.24 When messing with seacocks with the boat in the water, have a selection of wooden emergency bungs/pl |
||
What are these tracks used for?
Will Gilmore at 5:47am 07.09.24 Thought the pulley was the round part inside the block I get the impression that "sheave" (sheeve? |
||
electric windlass
jviss at 5:44am 07.09.24 @dlochner is right on, and clear. I only part from his advice in terms of the battery. Were I to i |
||
Installing a EV-100 Cable question (1)
jviss at 5:08am 07.09.24 If I understand your physical network correctly, and I recall my STNG networking correctly, and that |
||
electric windlass
dlochner at 4:30am 07.09.24 The decision to use a horizontal or vertical windlass depends on the chain fall. If the chain has to |
||
standing rigging got looser
east coaster at 4:08am 07.09.24 Had the same issue on my previous boat a 1983 Catalina 30, mast stepped on deck. Removed deck step o |
||
Yanmar Diesel cooling blockage at street nipple to exhaust
bris59 at 7:51pm 07.08.24 All - thanks for the replies! I did a methodical step by step replacing the impellor on my 3GM30F a |
||
standing rigging got looser
Project_Mayhem at 6:29pm 07.08.24 It takes a few sails every spring to get the stays tight on my boat. Mast step was rebuilt. |
||
What are these tracks used for?
Rick Webb at 6:21pm 07.08.24 Thought the pulley was the round part inside the block |
||
Installing a EV-100 Cable question
Don Crowther at 6:17pm 07.08.24 So the white goes from the p70 to the T and then the blue will go to the 5 way connector block. Wha |
||
What are these tracks used for?
ggrizzard at 6:12pm 07.08.24 I had a rough day... I needed a good laugh. Thanks Guys (and Gals)! DEI strikes again... :laugh: |
||
CITRISTRIP to strip varnish?
nightowle at 6:00pm 07.08.24 It works, but it's tedious.....it's not magic. It will take multiple applications if the varnish is |