Tod
at 7:47am 12.30.10
3/4020
Was the Lancer 25 ever built by a company called Glassline Products? Here is a boat that the owner
|
||
Ketoj
at 7:04am 12.30.10
8/9667
After years of pain in maintaining the narrow teak eyebrows along the length of the cabin top, I pur
|
||
chefmike
at 6:09am 12.30.10
5/1616
http://sailingtexas.com/201009/sventure24102.html
|
||
ericson_adam
at 7:02pm 12.29.10
6/3066
A couple of month ago, I bought a boat that was discussed years ago on this forum. The Ericson 29 h
|
||
gettinthere
at 5:01pm 12.29.10
0/1334
2 free seafrost plates. Taken from an 80's vintage Mason 42. No signs of leaks. One is diagonal cut
|
||
ocean5
at 4:55pm 12.29.10
5/2826
good day ,even in winter time .we have a beneteau 373 with seafrost fridge system . i find that it d
|
||
jfrench
at 4:48pm 12.29.10
9/3862
IS the Davis Tiller Tamer any good?
|
||
Jim Douglass
at 4:18pm 12.29.10
2/1244
Has any one replaced the opening ports (just the opening part) in a 1984 Hunter 31
|
||
Siamese
at 4:11pm 12.29.10
8/2419
This may be sort of a fundamental (sounds better than stupid!) question, regarding adding additional
|
||
Roger Long
at 12:50pm 12.29.10
37/8487
In the "What you can get away with" department": I measured up my mast carefully today so as to lay
|
||
faisond
at 12:18pm 12.29.10
3/1445
Looking for a source for a replacement thermostat for my Adler Barbour refrigeration system. Unit r
|
||
Peter Fridman
at 11:53am 12.29.10
12/7720
I live in warm waters so I could do this today, I do not want to haul the boat out of the water to c
|
||
Team118
at 11:36am 12.29.10
4/1573
I can't wait for April, 2011 to get here! I was looking at a few videos I took of my boat this yea
|
||
aduffE37
at 10:55am 12.29.10
38/12571
Lets see if this works. Can you recognise this place?
|
||
rvroamn
at 10:31am 12.29.10
3/2402
I'm shopping for a boat and found a 1987 S2 7.3. There is not a lot of information about this model
|
||
Chuck32
at 10:04am 12.29.10
6/3449
I have a 1987 Catalina 30 and for as long as I've had the boat (~ 20 years) it's been as dry as a bo
|
||
nauticalrich
at 9:49am 12.29.10
2/1671
I have a 1985 31 foot Oday with the sugar scoop. I want to get a bimini top, rail mount and wonder i
|
||
kpgraci
at 7:48am 12.29.10
10/1877
Just put my new sailcovers on - which means no more putting on and taking off the sails every time I
|
||
metalman
at 4:14am 12.29.10
1/1289
Our 1994 35.5 salon table has a mechanism to allow movement of the height for table use or for bunk
|
||
Andy1237
at 7:54pm 12.28.10
2/1879
Our club recently had over 5 shore power cords stolen. While I will be scouring Craig's list and E-
|
Searching for my 40 O'Day stolen from Sandusky Harbor Marina
Crusty Ol Salt at 3:17am 11.25.21 Recently in Richmond Virginia, someone did try to steal a sailboat. https://www.latitude38.com/lect |
||
Water tank pick up
Slipin Away at 1:54am 11.25.21 try with a long wire tie. It will not kink making the bend |
||
Can't get yanmar 3GMF above 2200 rpm under load question
Alan Gomes at 9:38pm 11.24.21 4. Changed the primary and secondary fuel filters even though they only have very little hours on |
||
Can't get yanmar 3GMF above 2200 rpm under load question
Capt Robbie at 8:13pm 11.24.21 Ralph, I formulated a plan based on the suggestions given from my friend who is a diesel mechanic a |
||
CNG to propane
sail sfbay at 8:07pm 11.24.21 ............I need the complete instructions fo converting CNG to Propane, with estimated cost...... |
||
Hatch Leak
jaysweet at 7:32pm 11.24.21 Thanks for the advice, guys. (Sorry not to reply sooner: work and all...) After some outside reading |
||
CNG to propane
jssailem at 6:19pm 11.24.21 I need the complete instructions fo converting CNG to Propane, with estimated cost. With such a qu |
||
Custom seadek
Flying Jay at 5:28pm 11.24.21 How do you glue it down? It appears to be mounted directly on top of the non-skid. Has a good adh |
||
Custom seadek
KZW at 5:14pm 11.24.21 How do you glue it down? It appears to be mounted directly on top of the non-skid. |
||
CNG to propane
dlochner at 5:07pm 11.24.21 Cost is hard to predict because each boat is different. To do this safely at a minimum you will nee |
||
CNG to propane
sail sfbay at 5:06pm 11.24.21 Welcome to the forum!! This thread can answer your questions conversion requirements Converting fro |
||
Custom seadek (1)
Flying Jay at 3:47pm 11.24.21 It sure looks great. What did it cost in the end if you don't mind sharing? is that like a 5-6mm, |
||
La Niņa
Rjm st.petersburg at 3:18pm 11.24.21 I like to use the Sailflow app. It seems to have quite a few local stations in FL. for forecasting. |
||
Water in Engine Pan?
valcour at 2:59pm 11.24.21 Do you have a drain hole that allows packing gland water leakage to drain to the bilge area? If so |
||