Serving sailors online since 1997
 
 

Recent Topics

Kermit at 6:14am 05.23.11
8/2746
We finally did it. We finally flew our spinnaker yesterday at Wateree Lake. We figured the wind woul
Smitty at 6:06am 05.23.11
7/2724
On the bow deck of my Cal 28-2 i have a padeye for a block that's used to turn the spinnaker foreguy
teacherspet at 5:28am 05.23.11
21/5404
Has anyone had experience in replacing the aft starboard Bulkhead on an Oday 25? The upper right cor
luken7 at 4:51am 05.23.11
2/2137
On the B361, there is a coachtop cabin vent. I'm wondering if anyone has replaced that with a solar
bowlinguy800 at 9:22pm 05.22.11
1/1339
I have my Cat 22 almost ready to put in the water for the first time. However I need to clean the cu
thatguy at 9:06pm 05.22.11
5/2367
need help/advice on gettin a 27 morgan from lake norman in nc to lake hartwell in SC
Stevew123 at 8:37pm 05.22.11
1/1253
Hi We are looking at converting our 410s two rear cabins into a master cabin, has any one done so
gary at 7:25pm 05.22.11
6/2200
Why do I have to paint the bottom of my boat at all? I live and sail on the upper coast of Maine wh
catshadowzoo at 7:18pm 05.22.11
Cal
0/2577
Need Help from any Cal 2-30 Owner or Cal 2-29 Owner. Getting ready on a hawaii crossing and need to
jfrench at 7:00pm 05.22.11
2/1342
What causes turnbuckle ends and shackles to twist and distort? I just had occasion to inspect the st
Ken H at 6:54pm 05.22.11
2/1300
Anyone got an idea of where or who I might contact to get a pattern for a bimini for my Hunter 320
jfrench at 6:52pm 05.22.11
0/1094
Went to install a Perko 4-wire electrical connector for the mast lights as currently sold by Catalin
doehunter at 5:29pm 05.22.11
6/1985
I just spent the whole weekend working inside my Mac, putting up shelving, and mostly installing my
isaksp00 at 5:20pm 05.22.11
3/1448
I had to unpeel the edge of the white fuzzy "carpet" that lines the interior of my H23 to remove and
BMB61 at 4:51pm 05.22.11
3/1482
This was third time out on my cat 22 . I took my sister and her husbend out on the lake, good wind b
MLampner at 3:54pm 05.22.11
6/3279
Is there somewhere a pictorial or other resource that will allow one to properly identify the model
gmpphotography at 2:52pm 05.22.11
2/5233
I own a Mirage 27. The covers of the v-birth cushions have deteriorated and need to be replaced. T
Roger Long at 2:47pm 05.22.11
6/5308
My instinct is to extend my cruising grounds sequentially as I like to feel the sweep of changing ge
BruceG at 2:28pm 05.22.11
4/2244
I own a 1982 Hunter 27 with a Furlex roller furling. I had the mast rewired this Spring and now my j
Tom Hoffman at 2:06pm 05.22.11
3/3847
Just got started mounting my new motor mount. It will do away with the old off to the side motor mo

Recent Replies

Structural Foam
teacherspet at 5:54pm 09.25.22
Nice job! It's your own personal Watergate, eh? :clap: Yeah but no LEAKS
Gooseneck Vision 32
teacherspet at 5:53pm 09.25.22
You might be able to buy a new endcap for the boom and gooseneck assembly and attach that to your b
Boom kicker or topping lift?
DayDreamer41 at 5:50pm 09.25.22
If you go with a kicker then make it active (internal gas shock) and you will have to also add a boo
Gooseneck Vision 32
rgranger at 5:18pm 09.25.22
You might be able to buy a new endcap for the boom and gooseneck assembly and attach that to your bo
Gray Enterprises Portlight lens replacement H33C
heritage at 5:17pm 09.25.22
A note on the pins.. Be extremely cautious removing and reinstalling the hinge pins. The little pos
Integral Fuel Tank leak
rgranger at 5:15pm 09.25.22
Is it possible to put a bladder inside the existing tank?
Structural Foam
jaysweet at 4:55pm 09.25.22
Nice job! It's your own personal Watergate, eh? :clap:
Boom kicker or topping lift?
mermike at 4:55pm 09.25.22
I like my Boomkicker. Just don't try to swing from the end of the boom. It will go badly.
Yanmar Engine Mount Worries
mermike at 4:50pm 09.25.22
I'm a follow the manual kind of guy. I never, ever assume that the "highly trained technicians" at t
Modified Traveler 23' Hunter   (3)
Harley215 at 4:42pm 09.25.22
209585209586209587
Frustrated, confused, and dissappointed
SoSound at 4:27pm 09.25.22
Well, the short term solution was pretty simple, I unplugged the temperature sensor and the charging
Bottom paint - Required? (in freshwater)
Jamesiv1 at 4:22pm 09.25.22
Wow. Read thru some of the threads and articles........ Looks like a lot bigger project than I antic
Invest 98L
jssailem at 4:15pm 09.25.22
The only thing missing are the goggly eyes
Structural Foam   (8)
teacherspet at 4:01pm 09.25.22
What tank did you replace with aluminum or poly. Im doing a refit on a vision 32 and po did not lav
Invest 98L   (1)
JamesG161 at 2:33pm 09.25.22
Through precise calculations and applying Science to maximum, John and I created our own model.
Yanmar Engine Mount Worries
jaysweet at 2:26pm 09.25.22
As far as fore/aft vs. port/starboard differentiation in motor mounts: all I can say is that Hunter
Gray Enterprises Portlight lens replacement H33C
kloudie1 at 2:12pm 09.25.22
A note on the pins.. Be extremely cautious removing and reinstalling the hinge pins. The little post
Hurricane prep in mast furling
capta at 2:08pm 09.25.22
It would depend on the strength of the storm, but as a rule, I'd remove that weight from aloft. Ther
Hurricane prep in mast furling
Davidasailor26 at 1:44pm 09.25.22
We pull ours IMF main in as far as it will go, then we disconnect the outhaul, wrap the clew around

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.