ehudm
at 1:36pm 05.10.11
23/5796
http://www.youtube.com/watch?v=WjW0cZHUvSQ'feature=player_embedded
|
||
woodster
at 1:19pm 05.10.11
4/1995
#1...ok ....i am in the middle of doing a barrier coat using West systems epoxy....i am at the sandi
|
||
shemandr
at 12:12pm 05.10.11
7/2943
The continuous furling line is slipping in the winch on the mast which turns the furling hardware wi
|
||
peter4504
at 11:44am 05.10.11
4/1181
I need to calibrate my wind direction meter with my wind vane. I have a 1999 Hunter 310 all the elec
|
||
Slipin Away
at 11:39am 05.10.11
5/4586
Does anyone know the manufacturer and/or web site for the push button cabinet latches Hunter uses fo
|
||
arknoah
at 11:38am 05.10.11
15/3868
Anybody have any experience with Trip Sailor, Sail Blogs, or any other free internet based sailing b
|
||
Snotter
at 11:07am 05.10.11
13/5119
I can't find a commercial vented loop to fit my 2" exhaust line; everything is too small. Do I have
|
||
OldCat
at 10:15am 05.10.11
8/7807
With a new Genoa ' since I need to set up telltales for it: What length and material have you found
|
||
Joe Mullee
at 9:40am 05.10.11
5/2048
What Happened To Fred Ficarra? Remember Fred Ficarra? I often think of him and refer to his work wh
|
||
Jtoben
at 9:10am 05.10.11
3/1518
Does anyone have any good condition side wall fabric left over that could be used to stitch together
|
||
jjclynick
at 8:55am 05.10.11
5/2884
I am taking possession of a '76 Oday 23' with a detached cable to the swing keel. Looking for advic
|
||
shemandr
at 8:34am 05.10.11
6/3468
After putting in my vertical battens on the H356 furling main I was having difficult time furling th
|
||
lorrieanne
at 7:18am 05.10.11
15/2721
We are new owners/ sailors with an older Catalina 30. I've been going through the original manuals a
|
||
Kevin3447
at 7:15am 05.10.11
2/2404
I posted this before, but I can't find the topic anywhere, so I'll try again - I have an O'Day 28
|
||
Joe D Pye
at 7:07am 05.10.11
5/2832
Help! I am getting steam from outboard exhaust from my 82 Catalina 30, Universal, two cylinder dies
|
||
Gary_H
at 6:51am 05.10.11
4/2928
Peggy, I installed a anti syphon valve at the top of the loop for my raw water intake hose for the h
|
||
dlewis812
at 6:33am 05.10.11
2/1899
have used marinas.com interactive charts on many occasions.. to make my route and check out marinas
|
||
sguice
at 5:31am 05.10.11
13/10116
We just purchased a new 2008 Hunter 146. After the initial rigging, I thought I would leave the mai
|
||
Brahmany
at 3:17am 05.10.11
2/2565
Is there a LED replacement for the halogen interior lighting on the C320? Cheers.
|
||
mbatsea
at 12:43am 05.10.11
1/1095
I am away from my boat for a few weeks. Would anyone know the diameter of the speakers in the cockp
|
O'Day 23 interior repair questions
Maks_s at 7:38pm 06.06.22 Grill brush work fine, but in some places I'm using scraper first. Tomorrow planning to try drill br |
||
Hunter 22 keel roller pin
Benny17441 at 7:37pm 06.06.22 Get adequate measurements for the pin, Length X Diameter. Also measurements for Location and diame |
||
Catalina 25 electric
Benny17441 at 7:17pm 06.06.22 The outlets in the cabin are likely 120V and you need to be connected to shore power for them to wor |
||
In mast furling?
esedenka at 6:38pm 06.06.22 Starboard tack is what seems appropriate but if you have vertical battens with the pockets on the po |
||
79 C&C hatch cover
DArcy at 6:24pm 06.06.22 I had a 1974 C&C27, the 30 is basically the same design, just bigger. When I removed the hood off th |
||
Fitting a bigger anchor on a Hunter 45cc
esedenka at 6:17pm 06.06.22 Z83, How did it go with the Mantus 85lb setup? |
||
79 C&C hatch cover
FastOlson at 6:09pm 06.06.22 The cover plate/top that your hatch slides under is usually called a "sea hood" or a "hatch garage". |
||
Green Crystals in Fuel Filter
SailingLoto at 5:56pm 06.06.22 This makes the most sense, not very mysterious, but makes sense Yeah, I find it in the fuel pumps |
||
Do I have a teak interior or cherry?
Sailor Sue at 5:17pm 06.06.22 Not cherry. Any pictures of a bigger area of the wood - maybe a little less upholstery? Another pos |
||
Cracked hull (3)
SailorHunter at 5:08pm 06.06.22 Some, including myself, have remedied this by using expanding foam or Gorilla glue. Which works bes |
||
Cracked hull
SailorHunter at 5:01pm 06.06.22 The most likely it was roto-molded Polyethylene and then filled with expanding foam to stiffen it. |
||
H 41 CUTLASS BEARING REMOVAL and SHAFT REPLACEMENT PROCEDURE
Tally Ho at 4:08pm 06.06.22 I would like to share my troubles that I have encountered while I was on this. First after 17 years |
||
Funny Friday!!! (1)
Will Gilmore at 3:58pm 06.06.22 That some high steaks grilling right there. got to keep your BBQ safe. |
||