jrale
at 5:07pm 09.01.11
5/3921
Macgregor Owners, The headboard on my main sheet fell apart while lowering the sheet on return fr
|
||
Larry Jackel
at 4:56pm 09.01.11
8/2051
The screens on the 4 topside ports on my 2005 H44AC have died and I have been unable to find the m
|
||
edbulmer
at 3:54pm 09.01.11
4/1235
My engine runs great lots of power but it is hard to start. Have replaced both filters and tightene
|
||
raffo
at 3:02pm 09.01.11
27/9752
I found that pushing the pop top up with one hand and then holding it up with my head and then raisi
|
||
pvbob
at 2:09pm 09.01.11
1/2072
Does anyone have spec/drawings for the centerboard for a S245? Thanks, Bob
|
||
Bad Obsession
at 2:01pm 09.01.11
9/6945
I have a seeking suspicion that I am getting some odors in my boat from my holding tank vent hose.
|
||
JamesO256
at 11:34am 09.01.11
4/1445
I have a 1983 22 foot swing keel. What would be a safety zone 4 open water.
|
||
Roger Long
at 11:34am 09.01.11
3/4258
There aren't many. The ship's photographer was distracted first by the beauty of the coast and then
|
||
rgreno
at 8:55am 09.01.11
4/2622
I have to replace the rubber boot around the leg on my yanmar sail drive but can't seem to find a ap
|
||
neilmcc
at 8:29am 09.01.11
16/4060
Wiring on the 336 and refrigeration Back again... I want to fit a fridge unit to the coolbox and va
|
||
MSter
at 8:03am 09.01.11
2/1739
Rich, last we heard you were looking for a spot to weather Irene around NYC. What did you find ? How
|
||
Ed Schenck
at 7:40am 09.01.11
14/3026
There have been several posts recently(and forever) on the subject of batteries and chargers. Almos
|
||
hpojrhi@gmail.com
at 9:24pm 08.31.11
0/1643
I'm considering purchasing a Lancer 38 center cockpit and was wondering if anyone has any knowledge
|
||
bustedrudder
at 8:45pm 08.31.11
7/3359
My 40.5 (3 months old to me) has the original Dytek GP1230 charger which is by all accounts obsolete
|
||
Dan Johnson
at 8:20pm 08.31.11
8/2546
I was finally able to get down to my boat today at the top of the Chesapeake Bay. I was an advocate
|
||
Runaway2
at 8:19pm 08.31.11
22/8200
We sail a 1985 Pearson 303 and estimate our Yanmar 13 horse to have roughly 1800 hours on it. A new
|
||
Repro
at 8:02pm 08.31.11
0/1833
G'day all. The cables going to my steering quadrant come in at a slight angle. Is this normal on a
|
||
c_witch
at 7:25pm 08.31.11
120/18342
I invite all on this board,if you agree that the poor owner of the boat that has been beached in Nor
|
||
rlrmystic
at 6:45pm 08.31.11
3/1565
I'm getting closer to owning my H29.5. This boat has sat. A number of months . So I figure this grou
|
||
eliems
at 6:30pm 08.31.11
3/1343
On the close reach with the main reefed we needed to move to beam reach to avoid land but the gusts
|
Beneteau Oceanis - tips for draining bilge?
arf145 at 11:58am 07.12.22 Wet vac sounds good to me...and then expect to do it some more after you sail a bit. Water hides up |
||
Soft Spot Repair - Lay New Glass Or Reuse Old Glass?
stickinthemud57 at 11:51am 07.12.22 Pictures would help, I think. As you alluded to, one challenge will be making a solid attachment to |
||
A "green"dilemma. What would you do?
Project_Mayhem at 11:22am 07.12.22 Try Amsoil's Outboard Premix 100:1 to reduce the amount of smoke and oil going into the environment |
||
Battens on the jib
shemandr at 11:06am 07.12.22 The pro's I can see are longer jib life and consistent shape. The con's could be in light air getti |
||
Whisker pole on jib - sheet or clew ring?
stickinthemud57 at 10:55am 07.12.22 I'm with you - I usually sail shorthanded and the simplest technique is what I use - clipping to a |
||
throttle brake (1)
Calif. Ted at 10:50am 07.12.22 doesn't seem possible for the hex head tension bolt to bottom out, it's not missing is it ? |
||
Whisker pole on jib - sheet or clew ring?
stickinthemud57 at 10:33am 07.12.22 DArcy in the 4th response up above gave the simplest solution to your question - tie your jib sheet |
||
Raw Water Pump Inspection - Oberdorfer
JoeWhite at 10:26am 07.12.22 The impeller will not come out of the other end. You still have to remove the C clamp in front and p |
||
Paddle wheel thru hull dripping
JoeWhite at 10:21am 07.12.22 Can you move the O rings from the plug to the wheel, that way you will know if the O rings are worn |
||
Cabin skylights and (1)
Calif. Ted at 10:18am 07.12.22 For issue 2 I use a claw grabber tool to thread lines thru clutches. Issue 1, I had a 270 and rememb |
||
Battens on the jib
Hollyberry at 10:08am 07.12.22 Some headsails without hollow leaches will have short battens to support the leach. Even some furlin |
||
throttle brake
Hollyberry at 10:05am 07.12.22 A slit rubber tube bridging the casing/pushrod junction... tight clamp on casing, adjustable clamp o |
||
Spinnaker sheets
shemandr at 9:56am 07.12.22 For spinnaker sheets floating is good too. A little stretch isn't so bad. For those sudden pops af |
||
throttle brake
Parsons at 9:49am 07.12.22 Meh - perhaps theoretically dangerous, but I never felt unsafe. Only used it for cruising because th |
||
Whisker pole on jib - sheet or clew ring?
Sailor Sue at 9:47am 07.12.22 The focus is on the absolute most simple solution that will be safe and minimize foredeck time. T |
||
Spinnaker sheets
dlochner at 9:43am 07.12.22 Spinnaker sheets are usually twice the length of the boat, two 60 foot sheets for your Pearson 30. |