Kermit
at 10:48am 11.22.21
1/414
200376
|
||
Brian D
at 9:26am 11.22.21
21/1541
I think the concept would be very close to be the same. How would I repair this without buying a ne
|
||
dslance
at 7:08am 11.22.21
4/1648
I'm moving my Beneteau 42 from St. Mary's, GA to Galveston, TX and plan to layover in Miami to atten
|
||
Randy Michaelis
at 7:53pm 11.21.21
5/1205
|
||
Apex
at 5:31pm 11.21.21
4/1759
added for clarification: fiberglass tube is packed with grease (zerc fitting) C'C 30: Fiberglass
|
||
jssailem
at 12:11pm 11.21.21
5/895
|
||
jssailem
at 11:02am 11.21.21
21/2220
More news from my buddy Rufus. He affirms that the affects of the ENSO activity will continue to br
|
||
Dinghy storage (1)
NYSail
at 9:07am 11.21.21
5/719
|
||
Giro
at 8:24am 11.21.21
2/494
Does anyone know where the Cruise Forum went? It was here one day and gone the next. (???)
|
||
SailorElliot
at 7:15am 11.21.21
10/736
|
||
Hatch Leak (1)
jaysweet
at 5:23am 11.21.21
5/731
I discovered some wet cushions in the v-berth right after haul-out. Testing with a hose revealed a l
|
||
All U Get
at 4:30am 11.21.21
32/1669
|
||
johnstreatfeild
at 2:57am 11.21.21
3/556
The plastic part that the the handle goes into on my Rule bilge pump broke. Does anyone know where
|
||
eianm
at 9:47pm 11.20.21
16/1156
I am wondering if any other 4JH2TE owners have had an issue with diesel in the bilge. It seems to me
|
||
CaptainRan
at 9:12pm 11.20.21
6/666
There is a small hole in the top of my mast. It appears to have been manufactured that way. I am gue
|
||
brian cc27mkiii
at 6:07pm 11.20.21
11/1757
looking for recommendations on repair material. i have removed the tabernacle fiberglass skin and we
|
||
fred1diver
at 4:16pm 11.20.21
41/5360
hey everyone, I know I would rather have a blue water boat but until I get enough money to find my d
|
||
fero
at 3:11pm 11.20.21
5/602
Hello all after quite a while, It looks like there is fissure in the outside part of the chainplate
|
||
rgranger
at 2:09pm 11.20.21
17/1114
Saw this boat today I think I could get it cheap:biggrin:
|
||
Phil Herring
at 8:12am 11.20.21
50/4278
Who do you thank for helping you get into sailing?
|
Use of C.S. Johnson Quick Release Levers on standing rigging
Project_Mayhem at 1:07pm 03.24.24 I had one on a 19' trailer sailor. It was fantastic. Fine adjustment was made with the back stay to |
||
Capri 18 battery
Project_Mayhem at 12:56pm 03.24.24 He didn't say what his charger was. I wouldn't normally recommend AGM since they are generally more |
||
Capri 18 battery
JBP-PA at 12:53pm 03.24.24 He didn't say what his charger was. I wouldn't normally recommend AGM since they are generally more |
||
Capri 18 battery (1)
Project_Mayhem at 12:45pm 03.24.24 Here's my work, I believe I calculated everything correctly at 12v? Worst case usage, USB assumes c |
||
M25XPB eng/battery fuse size (2)
jssailem at 11:29am 03.24.24 Clyde I had to redo my cables and fuses after the inundation of water in the boat occurred last Augu |
||
Suggestions on South Florida Towns to Retire To?
dlochner at 11:08am 03.24.24 The only two places in FL that I would consider are Key West and St Augustine. There is an interest |
||
1984 Hunter 34 Fuel Fittings
Ralph Johnstone at 11:01am 03.24.24 The tank was made by Inca Marine in Nashville, Tn. They were sold to SeaStar Solutions some years b |
||
M25XPB eng/battery fuse size
Stu Jackson at 10:23am 03.24.24 Battery cables red one connected to each end of both fuses. Located next to batteries. Clyde, I |
||
1999 450 salon table pin (1)
JamesG161 at 10:11am 03.24.24 Here is mine on the H430. Excuse the dirt , shown after Hurricane Damage |
||
M25XPB eng/battery fuse size (3)
Richard19068 at 9:55am 03.24.24 I don't have an answer but might suggest that the "guy doing work" should have a pretty good idea of |
||
Suggestions on South Florida Towns to Retire To?
PaulK at 9:32am 03.24.24 The east coast of FL might be better suited for the draft you want. Palatka, on the St. Johns River |
||
Suggestions on South Florida Towns to Retire To?
dLj at 9:27am 03.24.24 @dLj thanks! I've never been to St. Augustine but I heard it's beautiful. I'm just dreaming of a da |
||
outboard hoisting
PaulK at 9:17am 03.24.24 If you're looking for SS tubing, junkyards can be a good bet. Hospitals use it for piping oxygen to |
||
Suggestions on South Florida Towns to Retire To?
IWannaGoSailing at 9:11am 03.24.24 @dLj thanks! I've never been to St. Augustine but I heard it's beautiful. I'm just dreaming of a day |
||
1967 Morgan 34 shaft removal
PaulK at 9:11am 03.24.24 If the shaft was purposely misaligned or you have a skeg version, maybe not. Otherwise it looks like |
||
1984 Hunter 34 Fuel Fittings
kloudie1 at 9:03am 03.24.24 Hold everything that is not being unthreaded.. (elbow as valve is removed, boss as elbow is removed) |
||
1984 Hunter 34 Fuel Fittings
Globe Pilot at 8:39am 03.24.24 Thank you all for the info! So consensus is that I should be able to thread the fittings out and wil |
||
Asymmetrical Spinnaker hardware (1)
JBP-PA at 8:26am 03.24.24 So I usually just use a downhaul on a block, or sometimes attach the tack directly to the stemhead o |
||
Suggestions on South Florida Towns to Retire To?
dLj at 8:26am 03.24.24 I'd look in the Tampa area - i used to sail down there a bit. But that was quite some time ago so fo |