SvenTheGoose
at 8:04pm 07.03.22
11/2740
Is the stuffing box on these normally sealed with packing or is there a compression nut type of thin
|
||
jssailem
at 5:51pm 07.03.22
1/282
One of the latest technological tools to support your electronic needs/habits... Oscar is an optical
|
||
adamv
at 5:07pm 07.03.22
5/1094
Hi I'm fitting an anchor light to my masthead- a friend sent up his drone to take pics and seems the
|
||
sunlover
at 4:22pm 07.03.22
8/893
anyone know what this knot is? they are used on clasps on my Beneteau.
|
||
pclarksurf
at 2:32pm 07.03.22
3/943
|
||
Tim Mills
at 11:53am 07.03.22
39/3819
Just wondering how many of you who have diesel engines use your engine compartment blower when motor
|
||
Boomer2it
at 11:00am 07.03.22
0/2
Posted this in a different forum thought I would put it here for everyone..... So hopefully I expla
|
||
judith
at 10:59am 07.03.22
2/660
Hello, I have leaky windows on my 1978 Catalina 25 so I got the kit from catalina direct to replace
|
||
Boomer2it
at 10:58am 07.03.22
14/1943
So hopefully I explain this correctly. My battery switch (off/1/2/both) 1 position starting battery,
|
||
Boomer2it
at 10:49am 07.03.22
0/8
So hopefully I explain this correctly. My battery switch (off/1/2/both) 1 position starting battery,
|
||
chrisyse
at 10:42am 07.03.22
4/1755
Anyone know of a depth sensor that can be linked to my Samsung tablet and phone? Any depth transduce
|
||
Two questions (3)
rogerbalz
at 10:35am 07.03.22
5/813
206864 What is this? Also what is the autohelm tridata? 206865
|
||
shank
at 9:33am 07.03.22
4/1965
Does anyone know where I can a replacement glass for a Perko oil lamp part 230? I managed to break m
|
||
MikeTheHunter
at 8:14am 07.03.22
17/1435
I'm installing a smaller evaporator - only one I could get as Isotherms are back-ordered till the en
|
||
Gratto 23
at 6:23am 07.03.22
7/869
We just purchased a 1987 23ft Hunter. Topping lift is broken. To order replacement, how long does it
|
||
Gratto 23
at 6:09am 07.03.22
5/1177
We have a new to us 1987 23ft Hunter. Discovered topping lift cable is broken. What is the length we
|
||
twodzusfittings
at 5:24am 07.03.22
18/2718
Please note, I found this diagram on the web. It gives the basic idea of how my set up is. My engine
|
||
SailingFree44
at 9:22pm 07.02.22
6/718
|
||
SailingFree44
at 8:12pm 07.02.22
59/3747
Good evening folks, So the 79 bilge finally went out and I am almost done installing the marine rai
|
||
SailingFree44
at 8:04pm 07.02.22
0/20
|
Hunter 40.5 Stbd water tank leak
smokey73 at 3:02pm 02.17.25 Agree with @Rich Stidger! I had the same problem with leaks at the screws. I did the same thing an |
||
interior boom assemblies?
shemandr at 2:09pm 02.17.25 I think having a functional outhaul is a great upgrade. As we know it controls the depth of the who |
||
Self-Bailer on Trinka 8' Dinghy
Skipper J at 1:00pm 02.17.25 Hi All, I appreciate the feedback. It sounds like I'd be better off leaving it as it is, with the dr |
||
Steps to open and check copper tubes on heat exchanger for Universal M25-XPB engine?
BigEasy at 12:43pm 02.17.25 I used a brass gun cleaning brush and rod (22 caliber diameter) to thoroughly clean the tubes. The |
||
Flanged seacocks installation with Beneteau grid liner?
dlochner at 12:40pm 02.17.25 I used a hole saw of the correct diameter, but without the pilot bit. It was hard to get the hole s |
||
Re-routing Mainsheet H27
David in Sandusky at 11:50am 02.17.25 I would suggest end of boom sheeting if this is at all ,possible. Our '77 h27 is sheeted from the en |
||
Re-routing Mainsheet H27
jssailem at 11:38am 02.17.25 I grew up sailing dinghies and small boats. I understand your experience of having the main sheet in |
||
Hunter 33 water leak at compression post (2)
KyleH at 11:15am 02.17.25 Thanks for the reply's. I did investigate the wire box, and it didn't appear to be the source, I'll |
||
Hunter 170 crack down to keel
DFD at 10:59am 02.17.25 You definitely have high stresses occurring under the cracks. This will require building up the hu |
||
Older CDI furler
Timm R Oday25 at 10:54am 02.17.25 Hopefully this will help . The shackle you show might as well be used securing the foot of the sail |
||
Flanged seacocks installation with Beneteau grid liner?
Ralph Johnstone at 10:50am 02.17.25 I could provide links to the owner's groups, forums where this has been discussed, etc, but this is |
||
Hunter 40.5 Stbd water tank leak
Rich Stidger at 9:51am 02.17.25 Try resealing the screws first before escalating the job. Access to the portside tank is hard becaus |
||
Steps to open and check copper tubes on heat exchanger for Universal M25-XPB engine?
JoeWhite at 9:19am 02.17.25 On my M35B Universal, the antifreeze drain is a plug on the engine block on the port side. Look on y |
||
Flanged seacocks installation with Beneteau grid liner?
jbmia at 9:17am 02.17.25 Hmmm. My last bullet point was this: "- None of this is helping the OP decide whether he can enlar |
||
Hunter 40.5 Stbd water tank leak
danielsan at 8:44am 02.17.25 Maybe you don't need to remove the lid. I had leaks on my port tank and I simply removed all of th |
||
Re-routing Mainsheet H27 (1)
DHembree at 8:35am 02.17.25 There is no traveler car, but a bridle that straddles the companionway with the cleat shown. Now, I |