Sitala
at 7:55am 03.03.12
1/1107
We have been dealing with a severe vibration with our S2 since we re-powered from a Volvo MD7A to a
|
||
Roger Long
at 7:36am 03.03.12
10/4750
|
||
unbusted67
at 6:49am 03.03.12
0/2778
I am looking for info on rigging dimensions and lengths for my 1983 Cal 35 but have so far come up e
|
||
titlestdan
at 5:43am 03.03.12
4/1371
I need to replace the carpet above the V berth"s and inside Cabin on my 1982 Hunter . Does anyone
|
||
av8erdunn
at 5:29am 03.03.12
6/2129
Has anyone put ac on a 23.5? I saw the one person who done it in the owner mods section but I want
|
||
DinoKanuck
at 4:53am 03.03.12
4/2351
Ahoy from Frosty Canada: The skinny... If we spend an extra $50 to buy a Victron BMV 602 over a
|
||
Shoaldrafter
at 1:40am 03.03.12
0/1497
Roger, So, you are checking out: http://www.pamlico.com/nce Lots of docking... lots of bugs in
|
||
abruzzi
at 10:10pm 03.02.12
3/4181
just curious, if I rig up a real topping lift for the boom to replace the pig tail, is there any rea
|
||
DianaOfBurlington
at 8:05pm 03.02.12
6/2190
I just posted this to my boat's blog about an impressive discovery. This ought to end a few argumen
|
||
doehunter
at 8:00pm 03.02.12
58/7299
OK, I'm heading out to check my batteries tomorrow. Depending on what I see tomorrow, I might bite
|
||
Styx
at 3:14pm 03.02.12
15/11146
I have a S2 8.0c and am starting to look for a dinghy. I am new to sailing. In my research, I cam
|
||
Don Guillette
at 10:37am 03.02.12
5/2756
Last week I was visiting Puerto Penasco, Mexico (Rocky Point to us in AZ). It's about 4 hours from T
|
||
Maine Sail
at 9:27am 03.02.12
47/20087
The Bad: We used Hydrocoat last season and absolutely will NOT be going back. I will go back to Ul
|
||
rexabbot
at 8:53am 03.02.12
3/1346
I just installed my Victron and it is works good. My question is, do I have to attach an alarm o
|
||
Jon_E
at 8:26am 03.02.12
5/2073
Hi - I'm looking for replacement splash guard material. Last year painted my deck on my 1977 Catal
|
||
leeroy brock
at 7:45am 03.02.12
1/1772
would like to contact other catalina 25 owners in or around the san francisco bay area
|
||
cb32863
at 7:33am 03.02.12
3/1481
Well, before I decided to try to bust my ankle a while back, I did actually start some work on my b
|
||
Styx
at 7:22am 03.02.12
8/2138
I have a S2 8.0c and am starting to look for a dinghy. I am new to sailing. In my research, I cam
|
||
brian3820
at 6:59am 03.02.12
10/1554
Hello, as many know, I have an 84 Hunter 34 that is being totally refit. This past fall I was able t
|
||
jgurley
at 6:10am 03.02.12
8/2602
I recently acquired a First 38, and the running backstay gear seems to be absent. Could someone des
|
1985 Pearson 303
jssailem at 6:28am 03.23.22 The engine according to a PRACTICAL SAILOR review Based on your questions and then this statement |
||
Do You Know A Good Broker?
jssailem at 6:15am 03.23.22 Boats here in the PacificNW are priced a bit higher that most other regions. As @dlochner stated the |
||
Hunter 34 (1984) Bimini from sailboatowners.com
RoyS at 5:56am 03.23.22 IMHO if you have the ability to dictate design, it is best to extend the back of the bimini over the |
||
Do You Know A Good Broker?
Prairie Virgin Sailor at 5:28am 03.23.22 Thanks for the feedback. Much appreciated. |
||
CENTERBOARD HELP (1)
twodzusfittings at 5:11am 03.23.22 203703 Centerboard finished. Cavity wall in the Keel repaired as needed. All ready for a new cable |
||
ICW actual state "of affairs" conditions
dlochner at 5:00am 03.23.22 There are lots of boats in Florida. Look closer to home. |
||
Hunter 34 (1984) Bimini from sailboatowners.com
sailermaned at 4:57am 03.23.22 I purchased one from them for my 31 which will be basically the same, and it does not go past the st |
||
1985 Pearson 303
dlochner at 4:57am 03.23.22 The going shop rates for boat yards is $125-150 per hour. If all goes well you have 2-3 days of labo |
||
Freezer repair, 2015 Oceanis 48
Roger F at 4:55am 03.23.22 It opened up fine! I will reach out or if need be coordinate with a local marine service repair g |
||
Semco Teak Sealer - progress photos
BigEasy at 3:07am 03.23.22 I used Semco on other wood on the boat and have photos of that if folks are interested. Look |
||
Starting over from scratch
BigEasy at 2:50am 03.23.22 Is that the shift mechanism that was originally used with your current motor? If yes, does that sh |
||
Wooden strip for Stern Rail Seats
Ken13559 at 2:26am 03.23.22 Thanks all. I'll have a word with local timber store. Will hunt for plast-teak as well but not going |
||
Scared myself - broken forestay
nightowle at 12:52am 03.23.22 Indeed, scary stuff. You handled it well. All the while looking searchingly at your first mate for |
||
Freezer repair, 2015 Oceanis 48 (1)
HaroldW at 12:19am 03.23.22 I was wrong about it being flat. I got the flat one for a different job. This is the parts breakdown |
||
Hatch handle
Mark Maulden at 9:25pm 03.22.22 This is going to need a pic. I'm wondering if the two pieces of teak are guides for sliding? |