domalon
at 12:37pm 06.18.12
5/1801
What is the optimum wind speed that an O'Day 23 can be sailed safely?
|
||
Roger Long
at 12:18pm 06.18.12
1/1635
I just went topside after a visit from one of the S.E.A. staff and looked over to see another resear
|
||
Knotsoffun
at 12:17pm 06.18.12
1/750
My tachometer on my 2006 Hunter 31 was working fine one moment, then pegged itself over 5K without a
|
||
Cwoody
at 12:00pm 06.18.12
20/7964
Held off for a year, but before it gets too hot on the Chesapeake Bay.... Looking to install a Flags
|
||
John23883
at 11:28am 06.18.12
5/1383
I have a Hunter 26 that has an "L" shaped sail stop with stamped wings that goes into a drilled hole
|
||
BobM
at 11:26am 06.18.12
2/970
Second session cutting access to my water tank. The dremel vibrating saw was a good tool for the jo
|
||
Hogfighter
at 11:06am 06.18.12
26/12967
Sailing in 20 knots of wind on a beam reach with a reefed main and jib, my starboard chainplate gave
|
||
Taurus
at 10:56am 06.18.12
11/1885
|
||
AXEL
at 10:49am 06.18.12
4/1072
It's been a while since I've been there. In the past I have motored around the Montauk Yacht Club an
|
||
Brooklyn
at 10:27am 06.18.12
6/6108
Just became the new owner of a 1975 10/4 and so far I'm loving the beamy little thing. She's been ke
|
||
Sails-n-Ales
at 9:37am 06.18.12
10/6034
I have recently purchased a 1982 36' Islander and found that the stuffing box has a recurring leak.
|
||
Joe5893
at 8:38am 06.18.12
15/4624
I did a search on the forums and couldn't find anything on this topic. I have leaks and the water r
|
||
c_witch
at 8:08am 06.18.12
15/4093
The only damage being a bit of scratched paint in docking at 4:00 AM in total darkness and my pride
|
||
Serena1
at 7:45am 06.18.12
110/23400
Welcome Hunter e33 owners. The administrator has setup a model catagory - e33. Although this is no
|
||
allen-deckard
at 7:42am 06.18.12
35/5491
Thought id start a thread about things from companies that had good or bad products that youd like t
|
||
ktbowles
at 7:24am 06.18.12
14/11833
I have a 2002 26X and have just ordered a new main sail with slugs and would like to install a Lazy
|
||
ge8679
at 7:16am 06.18.12
3/1501
My rudder makes a chatter noise which goes away at higher speeds. just hauled it and the shaft is ti
|
||
NYSail
at 6:41am 06.18.12
2/1797
Hello all..... I have a 1986 vintage P36-2. The boat has 4, 8.5 foot sections of 1" by 1" teak toe
|
||
Crazy Dave Condon
at 5:51am 06.18.12
2/1145
I closed American Marine ' Sail Supply, Inc last year. Last week, I finally sold the last piece of
|
||
joes new addiction
at 5:10am 06.18.12
4/1562
Had plans for "Father Day" to get up early and FIANLLY go sailing! I've been neglecting my poor boat
|
Stainless steel washers in electrical circuits
dLj at 9:42pm 04.23.22 304 and 316 are both 18-8 stainless steels. The difference is the amount of moly. No, all 300-seri |
||
Stainless steel washers in electrical circuits
thinwater at 9:30pm 04.23.22 Perhaps they supply fasteners that is 304 stainless or 18.8 ss stuff is magnetic So is 304 or 18.8 |
||
Which wood piece is stronger ? Solid or laminated ?
thinwater at 9:25pm 04.23.22 Without knowing the strength requirement, questions like this are always funny. No way of knowing if |
||
Needing a new motor for my Catalina 22
Gene Neill at 9:02pm 04.23.22 6HP is the sweet spot. Get the longest shaft available. |
||
Which wood piece is stronger ? Solid or laminated ?
Justin_NSA at 8:51pm 04.23.22 Ash and hickory are stronger than oak. Just FYI |
||
Diesel tank cleaning advise needed
Benny17441 at 8:36pm 04.23.22 Remove the tank to get it thoroughly cleaned; as an alternative for a tank in boat cleaning I would |
||
Legend 41 Forward Heads Hatch
sail sfbay at 8:29pm 04.23.22 Welcome to the forum!! Replacing old hatches AND removing the hatch, measuring the cut out is one t |
||
Beneteau Oceanis 381 Folding steering wheel?
Brad Cross at 8:26pm 04.23.22 Thanks for the reply. I assume it fit your Whitlock steering system fine. |
||
Needing a new motor for my Catalina 22
Benny17441 at 8:17pm 04.23.22 The 9.9HP 4 stroke is too heavy for that boat. |
||
Trans oil
Benny17441 at 8:11pm 04.23.22 For the 2gmf it is 30W engine oil but If you do not want to have to change the oil again ever go to |
||
Which wood piece is stronger ? Solid or laminated ?
Benny17441 at 8:02pm 04.23.22 The goal should be something that is good enough. |
||
Docking with a loop
higgs at 7:46pm 04.23.22 I use the same system with slight modification and it works great for me. It certainly eliminates p |
||
Epoxy and stainless steel.
NYSail at 7:41pm 04.23.22 By the look of it this a standard Volvo lipseal. Volvo does NOT mention this arrangement with the w |
||
Raymarine Wheel drive autopilot on Hunter boat- to upgrade?
higgs at 7:39pm 04.23.22 That's good, but it doesn't make it a good idea, in any event. There must be a reason that the mak |
||
Replacing engine mounts on '86 H34 (2)
WasabiRush at 7:24pm 04.23.22 Thanks. I got the front two done. It wasn't too bad. I took the opportunity to clean and paint the m |
||
Tohatsu Sail Pro starting issues
Leeward Rail at 7:11pm 04.23.22 Tequila maybe? That's for christening boats !:beer: |
||
New Owner Here! 36C Hull #44
chichiflys at 7:08pm 04.23.22 Welcome - '82 H36 here - I think #121....Family boat since '84. Lots of TLC needed but it's a fun t |
||