Benjamin Disralei
at 3:10am 11.04.12
3/2601
I would like to know the reason for the baby stay in front of the mast, I gather it is to stop the m
|
||
gpd955
at 11:26pm 11.03.12
2/1530
Towards the end of the season my Tides Marine SureSeal Dripless shaft seal became undripless. Tight
|
||
propellanttech
at 9:04pm 11.03.12
7/5084
I'm starting to look at Hunters to buy. I'm stuck between the 35.5 and the V36. My situation. To g
|
||
Jimongee
at 8:40pm 11.03.12
8/4273
I am a woodworker and I have a 356. I want to make a set of campanion way doors that are vertical b
|
||
AirBoyzT
at 8:07pm 11.03.12
20/3263
Yal have heard my story, thanks for the guidance and advice. As of today I am the proud owner of a 1
|
||
PGIJon
at 7:29pm 11.03.12
7/2259
I have to replace the halyard on the 110 furled jib. I can't tell if it 1/2 or 7/16... Also since
|
||
skyflyer
at 4:03pm 11.03.12
3/1514
My first post, so Hi all Catalina owners! :) So - someone must have had this problem before and s
|
||
frankiedogs
at 2:30pm 11.03.12
9/3213
I am redoing the bulkheads in the head. Rotted out at the bottom of the main wall. Any opinions on w
|
||
Roger Long
at 2:00pm 11.03.12
14/4056
|
||
jluke
at 12:41pm 11.03.12
3/2008
Does anyone know where I can find the serial number on a 1979 Irwin 39' citation? Not in the customa
|
||
Ralph Johnstone
at 12:08pm 11.03.12
26/5965
...................... will be rearing its ugly head next spring. I like to use two coats (a bit o
|
||
joker460
at 11:35am 11.03.12
4/1382
I saw a post back on another site dated 2011 with regards to a mod made to the main furling line to
|
||
rweiss
at 10:01am 11.03.12
9/2716
I need to replace the 5 hp outboard on my Hunter 18.5 and am having a hard time finding anything tha
|
||
walt
at 9:29am 11.03.12
22/4464
|
||
meirgerner
at 8:40am 11.03.12
8/2562
We consider to buy genneker for our huntrr 33. Any recommendations?
|
||
MacNCheese
at 7:50am 11.03.12
8/2653
I'm going to try to make my own mast raising system for my 26D that does not have the extra hole in
|
||
MacNCheese
at 7:39am 11.03.12
17/2770
As you can see from my custom Cabin Door on my 26D, the lock on the outside is ineffective because t
|
||
Vtotten
at 6:14am 11.03.12
1/1282
While preparing to go out sailing this morning, I realized the rudder would only turn to port. It wa
|
||
Roger Long
at 5:43am 11.03.12
8/2599
I've always been a bit mystified by the high view counts for this forum since I'm not doing anything
|
||
seadaddler
at 5:09am 11.03.12
0/821
Hi Some one tried sending me a private message but my message was full but now it is empty. My panel
|
EV 100 autopilot drive belt
StephenD at 9:08am 06.01.22 The belts available online mostly say their pn is D169, and are made to work with the MK I version w |
||
Charging from a tow vehicle
mermike at 9:08am 06.01.22 Is that because of the potential current draw? Yes, exactly. If you check the wire gauge on the 7- |
||
Charging from a tow vehicle
AaronD at 9:02am 06.01.22 Is that because of the potential current draw? I'm interested in this too. @mermike - could you el |
||
Charging from a tow vehicle
AaronD at 8:58am 06.01.22 The Victron Smart Orions do not have a setting for reduced current, it would always want to put out |
||
Beneteau 331 rear swim platform teak insert
CABixler at 8:56am 06.01.22 I took it off yesterday and parts were hard and sticking but much of it was a white soupy mess. I'l |
||
Charging from a tow vehicle
Tedd at 8:56am 06.01.22 ...you should not use the trailer wiring or 7-pin plug to power the DC-DC charger. Is that because o |
||
Charging from a tow vehicle
AaronD at 8:46am 06.01.22 I do a fair amount of these installations with RV's, and you should not use the trailer wiring or 7 |
||
EV 100 autopilot drive belt
Calif. Ted at 8:42am 06.01.22 Older Mark 1 wheel drives are black, gray wd's are Mark 2, they take different belts. I have purchas |
||
Max prop issues
fstbttms at 8:35am 06.01.22 concur, but better he gets correct settings for the engine/trans, so this is fixed just once. The |
||
Max prop issues
pipedream at 8:33am 06.01.22 concur, but better he gets correct settings for the engine/trans, so this is fixed just once. The y |
||
Single-handed docking
BigEasy at 8:25am 06.01.22 Oh I like that! So let me see if I have this right... you approach the dock and slip this line ove |
||
EV 100 autopilot drive belt
jssailem at 8:22am 06.01.22 :plus: i3DGear is a solid shop for some parts. He makes parts 3D printed. Is a designer and he stand |
||
EV 100 autopilot drive belt
Hayden Watson at 8:12am 06.01.22 If you are trying to keep an autopilot working it is a good idea to benchmark this web site. Autopi |
||
Vagabond 17 - (Standing Rigging Unknown) (1)
SteveG_Esc at 8:06am 06.01.22 Is this what you have on your stays? .. and it leave a little play in the tension. Hi, thanks fo |
||
How to connect VHF radio to NMEA2000 MFD
Matt White at 7:38am 06.01.22 Update: This was very easy to do! I took Tx+ and wired it to Rx+ and Tx- to Rx- on the NMEA0183 to S |
||
Furling System CF-700
kappykaplan at 7:32am 06.01.22 @circa1971la , that line looks like a jury-rig to keep the furler main housing from rotating when th |
||
O'Day 23 interior repair questions
Maks_s at 7:27am 06.01.22 First of all thanks for your responses! Hull liner, cool good to know. I see some waste and hope it' |