sunlover
at 9:06am 05.01.22
10/1129
are there any switches that I should be aware of? the controller looks weathered but I'll start d
|
||
sunlover
at 9:01am 05.01.22
7/574
cut two supports to prop open engine hatch.
|
||
Udi
at 2:40am 05.01.22
11/942
Hi! Anybody have information where to get deep stick for Hunter 45? Thanks
|
||
baycloud
at 11:29pm 04.30.22
23/1597
Hey everyone, back on the boat (in the rain). Made tons of progress, pulling really long days. My b
|
||
ricksoth
at 10:02pm 04.30.22
4/574
I purchased a hot/cold mixing valve from Fishermans and plan on incorporating it into my hot water s
|
||
shank
at 6:36pm 04.30.22
6/734
This isn't my boat and just using the photo for illustrative purposes since my set up and colors the
|
||
rpwillia
at 5:48pm 04.30.22
12/1004
I had a related discussion in the 310 thread, but have a new issue. To reinstall the one bolt, I nee
|
||
mechjagger
at 5:46pm 04.30.22
16/2294
Need some advice. My cat 22 has vc17 on the bottom and seems to have many layers of paint, it is al
|
||
Seamus603
at 4:23pm 04.30.22
7/423
Bought an "NTM"(New to me) Lightning late last year. Pulled it out of storage the other day, and was
|
||
racenmotorsports
at 1:52pm 04.30.22
2/376
I didn't find anything searching so..... Help! I was trying to clean up my boat today and commenc
|
||
dkinzer
at 1:14pm 04.30.22
2/601
On our H41DS, I recently had removed the floor panel immediately behind the helm station in order to
|
||
jim01749
at 12:34pm 04.30.22
4/474
Hi, I am looking to repair one of the clutches on a 4 bank clutch assembly. Unfortunately the nuts
|
||
brockangelo
at 11:58am 04.30.22
4/499
|
||
stephen covey
at 11:55am 04.30.22
3/548
We just launched our new beneteau 46.1 and the courtesy cockpit lights don't work. The switch for t
|
||
Randy_C
at 11:51am 04.30.22
0/280
|
||
sailcapt340
at 11:45am 04.30.22
6/411
|
||
Avi
at 10:44am 04.30.22
10/353
I got a 1979 S2 9.2 c. The floor under the compression post is very wet. Do I need to remove the ma
|
||
JRT
at 10:42am 04.30.22
13/1404
Sounds cool, rate of 0.3 liters per hour, and requires only 20 watts of power per liter. https://ww
|
||
twodzusfittings
at 8:01am 04.30.22
14/1370
I recently watched a You Tube Video from Lady K. It was in regards to: does one leave the transmiss
|
||
Wiring (6)
Rodsails
at 7:17am 04.30.22
5/924
Doing a major update on our 1987 Legend 45 after encountering a major under the water boulder near t
|
Removal of washer dryer
SV knot that bad at 8:22am 04.14.24 Thanks so much for that! Do you know how we get it out of the boat? |
||
How to tie up to a cleat (or how NOT to lose your dinghy)
Peggie Hall HeadMistress at 8:04am 04.14.24 As you walk around any marina you'll see a lot of examples of "If you don't know the knot, tie a lot |
||
WATERLOCK MUFFLER QUESTION
twodzusfittings at 7:53am 04.14.24 1st prize goes to: well a few of you! To clarify, the boat performed well on a short cruise, summer |
||
Portlight Glare Question
ggrizzard at 7:27am 04.14.24 Dave, the tinted lenses look "black" vs clear lenses. |
||
Replacing Sanitation Hoses & Fittings - Use of Sealant or Gaskets?
Peggie Hall HeadMistress at 7:04am 04.14.24 Use only teflon tape on the threads, NO sealant or gasket. You may need a gasket (rubber) between t |
||
How to tie up to a cleat (or how NOT to lose your dinghy)
Ward H at 7:03am 04.14.24 Glad to see the APS tutorials are still around. They produced several. Thanks for posting. |
||
WATERLOCK MUFFLER QUESTION
Clutch Cargo at 6:46am 04.14.24 Interesting thread. I thought I'd a few additional comments in case this type of issue comes up aga |
||
Electrical Symbol for preheat solenoid (1)
jssailem at 6:05am 04.14.24 Here is the way MaineSail diagrams the preheat solenoid. lead (press the glow plug switch) the sole |
||
Removal of washer dryer
Slipin Away at 4:41am 04.14.24 It is held in by just the boards attached in the front of the machine. The hoses are long enough so |
||
Hunter Lead Keels form the 80
Jim Legere at 4:16am 04.14.24 Anybody have a clue who Poured the Hunter keels for the big boats in the Eighties Are you asking |
||
Portlight Glare Question
dlochner at 4:07am 04.14.24 Hi Sailors, I'm planning to replace my Gray Industries portlights on my Sanibel 18. The old ones a |
||
Why not put a 9.9 outboard on my 320? (1)
Ralph Johnstone at 11:12pm 04.13.24 So those were 2 learning moments for me ;) Noooooooooo. Those two stories are your open ended in |
||
Large Frame alternator in M25XP (7)
Hayden Watson at 10:54pm 04.13.24 Well, I started the install today and it defiantly fits. The large frame is only a bit bigger than |
||
Replacing Sanitation Hoses & Fittings - Use of Sealant or Gaskets? (1)
Ralph Johnstone at 10:53pm 04.13.24 If I'm looking at this fitting correctly, it will not seal against the interior tank wall with a gas |
||
Why not put a 9.9 outboard on my 320?
Drinky Crow at 8:52pm 04.13.24 Hmmmm.... Kiwi dude at my marina went 'round Van Isl. with his wife and newborn in a Ericson 27 Atom |
||
Why not put a 9.9 outboard on my 320?
Tally Ho at 8:11pm 04.13.24 Curious minds want to know, what were the causes of engine failure in both of those cases ? No eng |
||
New Genoa questions
Calif. Ted at 6:17pm 04.13.24 I have been using Ullman, the Newport Loft (Santa Ana actually) for repairs. Last 2 have been purcha |