Serving sailors online since 1997
 
 

Recent Topics

eianm at 6:57pm 06.11.13
6/1264
on my 1991 H42, I find that underway my steering is very heavy, while when stationary it is fine. So
cherub78 at 6:45pm 06.11.13
3/1129
Hello. I have a 27 ft hunter 1978 and I tried taking the compas off to lube the chain and shaft on t
jmczzz at 6:39pm 06.11.13
23/5768
I have my M25 up off the trailer and tried to lower the keel with the winch. No go the winch only go
jimfrankelly at 6:38pm 06.11.13
0/934
I bought sails again from Martin at Somerset Sails in Barker New York. I had bought sails from him
jack egan at 6:33pm 06.11.13
0/1417
Are there any O'Day wildfire owners out there? I found one in the U K. The boat was designed by Ian
KingAirDriver at 6:31pm 06.11.13
2/1265
Got three quick questions. The stock oil pressure sender on the M-18, I take it it only works the
jimbesikof at 5:59pm 06.11.13
5/1829
I have a 2000 Hunter 310, The water heater is rusting a the bottom. I am going to replace it, but it
Old Sailor 2 at 5:38pm 06.11.13
3/680
As I work my way upgrading my '92 Passage I find new stuff to do every day. Our boat Gratitude sail
ridetheocean at 2:59pm 06.11.13
9/1760
Hello, thanks for all the help on the stanchion question. I have another question. Sometimes wh
gord331victoria at 2:25pm 06.11.13
2/2438
Anyone using this product? I am contemplating using it on my Bene 331, as up here in Canada, I am ti
Griffinroydonald at 2:00pm 06.11.13
6/1643
I have been chasing some electrical problems in the wiring for my boat and made the following discov
wufibugs at 1:27pm 06.11.13
9/3131
Kloudie's comment on another thread about steering cables got me to thinking that when I took down t
Bad Obsession at 1:17pm 06.11.13
34/4210
Most of you will remember my post about selling my Catalina 30. There are a lot of decisions that g
IslandDreamer at 12:21pm 06.11.13
1/1669
Does anyone have an experience with Custom Sailboat Trailers located in Bacliff Texas? I am looking
Jtoben at 12:04pm 06.11.13
S2
2/1086
We are considering replacing the engine raw water temp cold/hot gauge with one that has the actual t
doug fulp at 11:35am 06.11.13
2/788
I have a small tear in my main sail (catalina 22), can someone recommend the best way to patch the s
ranchu56 at 11:29am 06.11.13
1/734
ALCON, Installing Raymarine wheel-pilot on the Admiral's boat. Wheel with keyway centered at the t
jaraman at 11:16am 06.11.13
0/731
What are the dimension of the cutlass bearing for a 393 with 30mm shaft
JRacer at 11:12am 06.11.13
1/1786
I had to add some breakers to my 92 Beneteau First 310. Back of the breaker panel shows it was made
Happy Daze at 10:55am 06.11.13
3/1258
OK guys! Anyone know how high the spinnaker pole ring is on the mast? Apparently a spinnaker was an

Recent Replies

Fake Documentation Renewal Notice
BigEasy at 4:22am 02.15.23
Don't pay the renewal fee. The Documentation number remains with the boat even forever If you
Funny Friday!!!   (1)
DaveJ at 3:49am 02.15.23
213005
Is There a Bleeder Screw on My Stuffing Box
sailme88 at 3:33am 02.15.23
The bolt head is possibly a point to affix a bonding cable....
Is There a Bleeder Screw on My Stuffing Box
Marmalade at 3:28am 02.15.23
Looks similar... Water Cooled Stuffing Box
DX Cup   (1)
Drinky Crow at 9:37pm 02.14.23
^^Thanks for that^^ $2 hun a side w/splice......hmmmm https://www.premiumropes.com/dx-cup# https://p
Superstitous steps
FDL S2 at 8:26pm 02.14.23
I'm convinced most of us are somewhat traditionalist when it comes to our boats . After far too lon
DX Cup
FDL S2 at 8:08pm 02.14.23
I replaced my jib sheets with Marlow D2 Club lines last summer. The dyneema core is sk75 vs sk78 in
Funny Friday!!!   (1)
leo310 at 8:06pm 02.14.23
213004
Ouch!
Tally Ho at 7:42pm 02.14.23
I am in a municipal marina on Lake Michigan, about 20 miles south of Chicago. I just paid my slip f
4JH-2TE oil sender Passage 42
Ralph Johnstone at 7:29pm 02.14.23
I Also found this potential candidate: Oil Pressure Sender for Yanmar Diesels perhaps the best of b
Ouch!
WayneH at 7:27pm 02.14.23
My old marina got bought out last year. The new owners are catering to powerboats. Not just any powe
Superstitous steps
rgranger at 7:23pm 02.14.23
Water system leak
rgranger at 7:22pm 02.14.23
If you can drain any remaining water you might be able to pressurize the lines with low pressure ai
Newbie installing a new thru hull transducer   (1)
Ralph Johnstone at 7:21pm 02.14.23
Very nice looking indeed. As a matter of fact, I think it would be even better if you didn't instal
Water system leak
twalker H260 at 7:00pm 02.14.23
If you can drain any remaining water you might be able to pressurize the lines with low pressure air
Newbie installing a new thru hull transducer
Ward H at 6:03pm 02.14.23
Very nice! Remember, we all started somewhere.
Newbie installing a new thru hull transducer   (2)
mforum at 5:59pm 02.14.23
I found a local engineering shop and the really nice guy there cut the G10 backing plate for me for
4JH-2TE oil sender Passage 42
juznip at 5:41pm 02.14.23
Yikes, I just looked up the price for that part at one supplier, ~$150! I have the 3 cylinder ver
Halyard Diameters 1979 H37C
Haul Away Jeff at 5:13pm 02.14.23
Thank you. You confirmed my decision.

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.