Serving sailors online since 1997
 
 

Recent Topics

bakeroo at 8:31pm 07.30.13
1/1613
I want to add a tiller extension to my C=18. Anyone done this? How far from the end of the tiller wo
caseylpz at 7:45pm 07.30.13
3/1044
I have an 85' H23 I can't figure out the boom rigging on it. Does anyone have photos they can post o
Craerz at 7:36pm 07.30.13
4/2559
Hello sailing folks, I have recently bought an old Idylle 11.5 by Beneteau, and there seems to be s
Chris Patterson at 7:02pm 07.30.13
44/8505
I was in a big box electronics store today, had to have a new router, plus I'm like a kid in the can
iSailor at 6:21pm 07.30.13
37/22195
looking for low-buck solution to making a companionway screen. Any insight / pictures or your so
Roger Long at 6:12pm 07.30.13
2/2298
Bruce Adams at 6:06pm 07.30.13
2/1210
I had coolant water in the oil in my Universal 5411. I just pulled the timing cover and found my rep
rudewarrior at 6:02pm 07.30.13
3/1212
Hwllo everyone, i have a 36 cherubini that had no companion way hatch when i bought it. Does abyone
weinie at 5:52pm 07.30.13
9/2117
`Is it so nice as all that?' asked the Mole shyly, though he was quite prepared to believe it as he
starrider1961 at 5:24pm 07.30.13
8/2576
I made an offer on a 84 Hunter 34 and it has been accepted I will be getting it surveyed. Can anyone
Nicolas Babic at 5:02pm 07.30.13
4/1154
Does anyone know where i can get the alumninum frame work for a 1996 Hunter 23.5 companion way enclo
Wedgie at 4:31pm 07.30.13
5/1188
Hi There, I would be interested to hear from any Hunter owners who have installed a Galvanic Isolato
jviss at 4:01pm 07.30.13
10/7474
Thinking of a B'G Touch 7 MFD and 3G or 4G solid state radar if I can't get my Raymarine radar going
stevestk at 3:22pm 07.30.13
5/2165
I'm a novice looking to move up to a 'big' boat. I guess I've been equating build quality with weigh
steve knoblock at 3:19pm 07.30.13
4/4107
The steering in my catalina 30 wheel is a little loose. I took the deck plate up to expose the cabl
jibes138 at 3:08pm 07.30.13
13/3513
I went out for a motor up the ICW on Sunday to have the boat hauled for a bottom job and assorted ma
bobweiser at 2:22pm 07.30.13
0/1642
The clutch for the auto pilot on my recently purchased Hunter 410 does not engage the drive sprocket
Al Garrett at 2:05pm 07.30.13
0/4284
Finally getting back to the trawlerization of my 2000 26X. Looks like the Johnson 25 hp in place wil
sharonburch at 1:55pm 07.30.13
10/1449
Picflight at 11:46am 07.30.13
5/2761
The islands look like a nice place to visit. http://youtu.be/1nRA_fY8v3o

Recent Replies

Recommendations for a new head
LD_C310 at 7:35pm 06.11.23
I installed a Raritan Marine Elegance with fresh water flush on my 310 last year - love it. It was
Hunter 23 gets a little water around the keel bolts.
Maureen S at 7:25pm 06.11.23
I am having this problem with my 1986 23 Hunter as well. This thread is very helpful. I have a cou
Looking for recommendations for Porta Pottie with MSD
Project_Mayhem at 7:04pm 06.11.23
We finally launched this weekend! Aside from a few minor engine issues everything went well @Gene Ne
Flimsy deck on bow and tabernacle. Backplate
Project_Mayhem at 6:54pm 06.11.23
One little tip... If you need to keep resin on the outer skin of the fiberglass while reducing the a
Need help: Mold in Toilet
dlochner at 6:35pm 06.11.23
Sorry not true.:badbad: We use Vinegar to make Pickles, not this medicinal Vinegar with the dead y
Yanmar Antifreeze Pump Bearing Problem
arcadiahunter28 at 5:14pm 06.11.23
Yeah, it looks like the bearings are shot, and who knows what else. You can probably rebuild it if
What's next to be aware of ?
rpwillia at 5:11pm 06.11.23
It could get dicey if you piss them off, but I would be thinking of carrying some M80s onboard.
Yanmar 1GM10 starboard rear engine mount removal
rpwillia at 5:08pm 06.11.23
Good advice here. If you are going to mess with one mount, while you are at it you may as well repla
New Alternator Regulator?
Maine Sail at 5:03pm 06.11.23
Yes the are Mc618H (H=harness)and I have piles of temp sensors too..These are way below distributor
Need help: Mold in Toilet
Tally Ho at 5:00pm 06.11.23
Yanmar Antifreeze Pump Bearing Problem
Tally Ho at 4:58pm 06.11.23
Yeah, it looks like the bearings are shot, and who knows what else. You can probably rebuild it if
Pumping out Hunter 380 Waste Tank - Macerator pump failed.
Terry Cox at 4:46pm 06.11.23
There is no wye valve on our boat just a top connection to the deck and a bottom connection to the
New Alternator Regulator?
jviss at 4:25pm 06.11.23
Need help: Mold in Toilet
JamesG161 at 3:33pm 06.11.23
The problem with using vinegar to clean mold and mildew is that it is mold and mildew food. Sorry
ISO Pacific Seacraft 25-2 mast, sails, righing
apell at 3:29pm 06.11.23
Sounds to me like you've found a donor boat for some one else's project. You might ask the yard ow
Need help: Mold in Toilet
dlochner at 3:27pm 06.11.23
My wife has found white vinegar to work better on surface mold than bleach. The problem with usin
Mast step
WI Rigger at 3:22pm 06.11.23
Dave, I secured the upper shroud to the aft eyelet on the amidship chain plate. In the owners manual
ISO Pacific Seacraft 25-2 mast, sails, righing
Joe at 3:17pm 06.11.23
I have come across a PSC 25, Mark 2, on the hard. It's been sitting a while. Yard owner states it i

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.