Serving sailors online since 1997
 
 

Recent Topics

boknows at 11:03am 08.02.13
13/4340
I built a gin pole for my oday 25. 10 ft long
Genkigary at 10:59am 08.02.13
5/2131
I'm thinking of removing the chart table on my '87 Hunter 34 so that I can extend the settee I sail
Mike19 at 10:27am 08.02.13
15/3905
I bought an abused 1980 O'Day 19 last fall, and finally got her in the water this summer. Like most
ChuckMinn at 10:20am 08.02.13
6/3933
Does anyone know where I can obtain plastic mast hoops for a 1964-65 Starcraft 14-footer? I believe
arjulian1@twc.com at 10:17am 08.02.13
3/1115
We are looking for replacement sail slides and shackles for a 1993 30' Hunter. So far, we haven't f
Roger Long at 10:11am 08.02.13
8/2952
Bandwidth is limited out here on the cell phone fringes so there are only a few pictures in this alb
Fred Villiard at 9:59am 08.02.13
2/2561
Maine, I think that I read in one of your posts that the ProMariner ProNautic P series chargers were
Dickbarton at 9:28am 08.02.13
2/1482
Can anyone help me figure out how to fix the cable on my O'Day 26 swing keel? --The Keel moves fr
tool_room at 9:26am 08.02.13
4/1709
I need information on tuning the standing rigging on my Hunter 18.5. I do not have owners manuals an
valhallasailingtv at 8:52am 08.02.13
0/995
Hello: does anyone have a lead on the cockpit seat's for the 26M. I've seen more than one brand bein
shanester at 8:41am 08.02.13
6/7938
I have looked into this several times over the past few years with no real obvious answers. Has anyo
csd0606 at 8:29am 08.02.13
13/5516
We are planning to mount solar panels on our H26. I have done lots of reading on what we need, what
89Mistral at 7:18am 08.02.13
3/2371
Catalina 36 with Jabsco Electric Marine Toilet. Toilet is reported to have trouble evacuating solid
AWalker at 6:29am 08.02.13
15/4417
I had ben running a 6hp Tohatsu that bought new after having my Honda 75 stolen on my '78 Oday 23. I
Shagdance at 6:28am 08.02.13
3/1709
Anybody using a folding prop? If so, can you recommend your prop? What mfg; size; 2 blade or 3 bla
leclaira@videotron.ca at 3:29am 08.02.13
15/4596
Desperately in need of a solution for a vibration-ratlling noise when motoring at certain RPM on my
Jutta at 11:08pm 08.01.13
9/1308
Hi there, we are the NEW owners of the 1995 Hunter 336 (Break Free) - former owner AB Lelystad, Neth
IslandDreamer at 10:28pm 08.01.13
5/1924
Well, it took a lot longer than I planned and a few more $$ but the old girl is heading back to the
hunter healer at 7:56pm 08.01.13
1/828
My 83 Hunter 27 Has A Soft Spot When Standing On The Deck About 4 Inches In Front Of The Mast In Abo
deckedout at 6:11pm 08.01.13
6/2410
Recently purchased a Beneteau 40 2008 model yanmar 53 hp and finding it difficult to start the engin

Recent Replies

Yanmar 1GM10 starboard rear engine mount removal
Ralph Johnstone at 2:27pm 06.10.23
The starboard rear mount appears to have deteriorated and looks to be partially collapsed. Any le
Mast step
WI Rigger at 2:05pm 06.10.23
I will have to go to the boat and take one. Tomorrow
Mast step
rgranger at 2:04pm 06.10.23
Pic?
Mast step
WI Rigger at 2:03pm 06.10.23
Should my mast have 10* or 15* aft rake?
2007 Hunter 2007 Rudder and Tiller alignment
isaksp00 at 2:03pm 06.10.23
What model boat is it?
ISO Pacific Seacraft 25-2 mast, sails, righing
apell at 1:48pm 06.10.23
I'm thinking the same thing...I'm in the midst of finishing a little catboat, to go sailing... You
Raymarine Autopilot Problems (ST4000+)
Tally Ho at 1:15pm 06.10.23
When I upgraded my old ST4000(+) to a ST6002, with a new Control unit, I put it in my lazzarette. M
Raymarine Autopilot Problems (ST4000+)   (4)
McPhee at 1:03pm 06.10.23
Hey everyone! I've embarked on the installation of the Raymarine EV100 kit. My initial setup will fo
Doesn't hurt to ask
Richard19068 at 12:28pm 06.10.23
Sorry, I got soo excited I hit the post reply button. Were the end blocks that you are showing mod
Adding soundproofing to companionway step
Richard19068 at 11:59am 06.10.23
Hi All, I hope your day is going well. I need a sanity check. I have the companionway step below
Glow Plug Push Button O'day 28 1985
Tally Ho at 11:53am 06.10.23
I found this which seems very much on point with my issue or at least a way fix things correctly. t
Glow Plug Push Button O'day 28 1985
Richard19068 at 11:35am 06.10.23
I found this which seems very much on point with my issue or at least a way fix things correctly. t
3D printing fun
Richard19068 at 11:07am 06.10.23
:biggrin: Conveniently his allowance is only enough to cover the filament needed to print for part
Non Skid; Black Spots
Richard19068 at 11:00am 06.10.23
s photo. Notice the relative uniform shape of the dark areas and how the white gelcoat fades away t
Hello to the community   (3)
RSHunter27 at 10:49am 06.10.23
graphics.
Main halyard shackle
Paul Ducham at 10:43am 06.10.23
Thanks! After posting my question, I found the 310 furling mast hand book from Charleston Spar. It

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.