|
gettinthere
at 6:25am 09.25.13
1/1091
Looking for recommendations for a moisture meter to check and monitor relative moisture levels
|
||
|
Kestle
at 6:13am 09.25.13
8/1430
I'm trying to figure out the best way to install this, as it would be nice to not have an extension
|
||
|
Michael Meyer
at 8:58pm 09.24.13
3/2378
I believe the frame seal on my forward hatch has developed a leak. Between the gel coat and aluminu
|
||
|
Sink pumps 1978 (1)
Golden Road
at 8:23pm 09.24.13
3/1495
Anybody have any advice on replacing a head sink pump? I can't figure out how to get the square plas
|
||
|
trainmanjess
at 7:18pm 09.24.13
3/984
hello all a little over a month back a shroud fastener broke and my mast tumbled... when it hit th
|
||
|
All U Get
at 3:26pm 09.24.13
5/1734
I don't know how I missed this, do you think this would buff out? http://www.penbaypilot.com/artic
|
||
|
fred1diver
at 3:23pm 09.24.13
24/12527
hey everyone quick question to all of you, what do you all use for some shade ??? I've thought abo
|
||
|
WhiteCap Fever
at 2:46pm 09.24.13
6/1430
I am looking for a trailer for my 1986 Catalina 22 as I will be moving my boat from Orlando to South
|
||
|
Bob S
at 2:03pm 09.24.13
10/2673
The "Dream Boat" thread had me looking at lots of dreams. :D I notice that newer and more expensive
|
||
|
jrowan
at 1:43pm 09.24.13
1/1447
So I had posted a while back if anyone new of parts for Hood furlers, as our older drum had cracked
|
||
|
nolasafari
at 12:22pm 09.24.13
5/1468
I decide to figure out which battery switch location on my boat was start and which was house. I sur
|
||
|
logothides
at 12:00pm 09.24.13
2/969
any body out there i lost my helm seat on my beneteau 281 in some strong wind,of course they do not
|
||
|
bffatcat
at 8:39am 09.24.13
4/3940
I have a 1975 pearson 26w with a cast Iron keel and galvanized keel bolts The bilge is always dry
|
||
|
Gunni
at 8:16am 09.24.13
64/25773
What a difference a week makes! Oracle Team USA has finally coalesced and is consistently sailing f
|
||
|
DanKo
at 7:23am 09.24.13
5/1262
I sail on a lake in the midwest. I normally keep the boat on a lift in front of my house. Because Wi
|
||
|
Boatalec
at 7:12am 09.24.13
4/2985
All, I just purchased a boneyard special Cat30 and the 3 piece doors are gone. Does anyone have a
|
||
|
PKFK
at 5:28am 09.24.13
6/1458
We have several of these (see picture) on our H36. No idea what they are for. There are 3 or 4 of th
|
||
|
krawall
at 3:43am 09.24.13
9/5835
Hello, I'm a new Beneteau owner, and say hello! Of course, I also have a question :-) Hopeful
|
||
|
Knot Flying
at 1:46am 09.24.13
10/1688
Does anyone know what length spinnaker pole I need for my Hunter 26? They seem very expensive and I
|
||
|
Eastwind
at 9:14pm 09.23.13
2/3412
I have a 98 Johnson 9.9 2 stroke in the motor well of my Catalina 27 that I want to connect to my sh
|
|
engine leak antifreeze
Tally Ho at 7:07pm 05.30.23 I am going to get a small mirror and try to see the back of the engine. That seems to be where the |
||
|
Installing Anemometer on Masthead - what should I expect?
shemandr at 6:08pm 05.30.23 For the education of the forum, do you think you could have done the task from a bosoms chair? |
||
|
engine leak antifreeze
CharlieAnn at 5:52pm 05.30.23 I am going to get a small mirror and try to see the back of the engine. That seems to be where the l |
||
|
Possible SmartPlug problem
jaysweet at 5:48pm 05.30.23 The last few fires in the marina were smart plugs. I do not know the details. Over time with my la |
||
|
1998 Hunter 376
Greg Mott at 5:48pm 05.30.23 Hi Rich, Thank you so much for getting back to me. This looks a lot like the crack I have at the b |
||
|
Continupus mainsail furling
danm1 at 5:47pm 05.30.23 If the line is moving freely through the mast winch then chances are it is too thin or too slippery, |
||
|
1998 Hunter 376
Terry Cox at 5:47pm 05.30.23 Hi Greg, Rich offers some sage advice. Lots of discussions on this site regarding cracks in the keel |
||
|
O'day 28 Needs a New Transducer (Airmar P79?)
Clutch Cargo at 5:37pm 05.30.23 Have you thought about installing one that shoots through the hull, eliminating any holes........My |
||
|
O'day 28 Head Finished
Clutch Cargo at 5:34pm 05.30.23 I think I know this boat....Is that you Pete? Could be......LOL |
||
|
O'day 28 Head Finished
Clutch Cargo at 5:33pm 05.30.23 Regarding the double clamping and length of the barbed fitting, ABYC only recommends double clamping |
||
|
Possible SmartPlug problem
Mark Maulden at 5:32pm 05.30.23 The last few fires in the marina were smart plugs. I do not know the details. Over time with my las |
||
|
Possible SmartPlug problem
jaysweet at 5:09pm 05.30.23 Not replacing a standard shore power cord based on one report of a failure in the absence of a defi |
||
|
Sealing shaft-log options (1)
ricksoth at 4:59pm 05.30.23 Here is the stuffing box alternative - plastic parts just for conceptualization. Bronze version beh |
||
|
Sealing shaft-log options
ricksoth at 4:52pm 05.30.23 Dave, how is creating an epoxy plug inside the tube just past (behind) the stuffing box cap replace |
||
|
Slow sump pump with backflow
Tally Ho at 4:48pm 05.30.23 Glad you got it sorted out. Jabsco is pretty proud of that pump! Hope it works out well for you. |
||
|
Sealing shaft-log options
dlochner at 4:36pm 05.30.23 By using a small portion of the tapered wood plug trimmed to "just barely" slide down the tube from |