tomfoolery
at 9:08pm 10.02.14
8/2012
I know the wooden base for The salon port side berth filler cushions must be a simple design but be
|
||
McIntoshUSA
at 6:52pm 10.02.14
2/2341
I saw this video and it got me thinking. Has anyone every built a small wind generator out of a ceil
|
||
jbinbi
at 6:48pm 10.02.14
16/4025
i have a 2012 e33. it uses pex tubing for the plumbing. on other older boats i was able to bypass th
|
||
Jeff10528
at 6:01pm 10.02.14
1/806
Was just reading the thread on Fuel Filters and it occurred to me that every owner should be aware t
|
||
ljcraigie
at 5:18pm 10.02.14
2/2064
I have the proverbial mast leaks with water streaming down the compression post. I imagine the mast
|
||
jhnewsome17
at 5:07pm 10.02.14
8/2662
On my 1987 Catalina 34 there is, according to the manual, a "Flapper Valve" on the exhaust hose at t
|
||
Meriachee
at 5:03pm 10.02.14
1/1368
Hat differentiates a 320 from a 320mkii ?
|
||
gregorybross
at 4:04pm 10.02.14
13/5071
I am going to replace the original above waterline thru hulls for bilge pump, propane locker drain a
|
||
SailboatInteriors
at 2:56pm 10.02.14
7/6246
A perfect cutting board set for your boat galley,containing three different sized boards, to find ju
|
||
Busy, Busy (1)
Roger Long
at 2:30pm 10.02.14
1/1151
I headed out from Chesapeake City bound for Worton Creek but rain persuaded me to pull in under the
|
||
RBWSAILBOAT
at 1:41pm 10.02.14
4/793
I recently purchased a 23.5 and whatever goes on the bottom of the mast crutch is missing. Any help
|
||
HMT2
at 1:20pm 10.02.14
3/910
Does anyone have polars for an 83 Hunter 31? I am heading for an offshore race next week and it's lo
|
||
Jim Seamans
at 12:01pm 10.02.14
8/2470
Getting ready to replace the zincs and it occurred to me as to where on the shaft is the place? I us
|
||
anthony
at 11:57am 10.02.14
8/1160
Hi All I think this might be a goody. My Ven 25 is sitting on the trailer, the keel is sitting per
|
||
Scott T-Bird
at 9:54am 10.02.14
61/13162
The recent "head or no head" discussion led me to think about our use of traditional marine toilet a
|
||
suvh8er
at 9:47am 10.02.14
18/3799
Hello Everyone, its been a few months since I've been on here, I have been too busy sailing! I wi
|
||
WoodyB
at 9:28am 10.02.14
4/912
I recently had my boat hauled out for minor repairs from Hurricane Arthur in July. Fortunately I too
|
||
Phil Herring
at 8:59am 10.02.14
24/1398
I noticed recently that Cruisers Forum is sending a daily email containing the new topics posted in
|
||
down_shift
at 6:36am 10.02.14
8/6532
My recently purchased 87' C36 came with a period correct Datamarine Link 5000 and autopilot. While
|
||
Tom Konschak
at 6:34am 10.02.14
4/760
Is The Yamnar Qm15 Water Pump Self Priming? If I Disconnect From Raw Water Intake Should It Be Able
|
Possible SmartPlug problem
Davidasailor26 at 6:03pm 05.22.23 From your description it sounds like this has now happened on two separate cords/plugs? If so I wou |
||
Reefing Sail Trim
Screen Saver at 5:44pm 05.22.23 Interesting topic But its far to wide to be one topic with one set of answers All the rigs are dif |
||
mast
stickinthemud57 at 5:27pm 05.22.23 jssalem's response illustrates the need for info. I broke my mast (Hunter 170), ordered a section t |
||
The Great Bilge Pump Debate, 2023 Edition
SycloneDriver at 5:23pm 05.22.23 Side note, we have what I think is a Tartan 38 at our marina. It's a fine looking boat! It almost |
||
The Great Bilge Pump Debate, 2023 Edition
SycloneDriver at 5:14pm 05.22.23 I certainly see the value of an automatic bilge pump! With today's available technology I'm just s |
||
older Raymarine L760 Instrument
RitSim at 5:11pm 05.22.23 I could figure it out if I had the plug. I've looked on the Raymarine site and it appears the devic |
||
older Raymarine L760 Instrument
jssailem at 5:09pm 05.22.23 You have the female end... Are there wires behind the pins? Wires connected to pins often give a clu |
||
older Raymarine L760 Instrument
jssailem at 5:04pm 05.22.23 Can you see the wires on the inside of the plug? They more likely can give you a clue. |
||
Engine Alinement (1)
Rjm st.petersburg at 4:48pm 05.22.23 This is what I used to get around sheard lag bolts when I was changing my motor mounts and replaced |
||
The Great Bilge Pump Debate, 2023 Edition
Hello Below at 4:45pm 05.22.23 I sort of do indirectly. I have a simple and cheap wireless camera located both above and below deck |
||
I broke my Sherwood Raw Water Strainer Winterizing Bowl....
dmax at 4:11pm 05.22.23 Yes - it sticks to everything, seals well. |
||
Puget Sound Chain Plate Replacement Recommendations?
Hello Below at 4:09pm 05.22.23 I met Ian when he was apprenticing under Brion in 2018. I found him to be very friendly and helpfu |
||
The Great Bilge Pump Debate, 2023 Edition
jviss at 4:07pm 05.22.23 I have the feeling that some of the folks on this forum that don't see any value in an automatic bi |
||
The Great Bilge Pump Debate, 2023 Edition
SycloneDriver at 3:48pm 05.22.23 This winter when I was at my boat I noticed my neighbors bilge pump running. It would run for about |
||
I broke my Sherwood Raw Water Strainer Winterizing Bowl....
sailcapt340 at 3:43pm 05.22.23 Is that the West 2 part adhesives your referring to? |
||
I broke my Sherwood Raw Water Strainer Winterizing Bowl....
dmax at 3:40pm 05.22.23 G-Flex would work. |