High Current
at 12:45pm 06.26.23
12/1658
My boat with a Universal M25-XP is still pretty new to me - I've only been out for a couple of sails
|
||
Plymouth Sailor
at 11:30am 06.26.23
3/471
I once moored my boat in a relatively sparse inlet so I could have a longer pendant. Now my pendant
|
||
Richard19068
at 10:39am 06.26.23
27/2013
Normally I would just use butt connectors but to ease installation of a new holding tank pump I want
|
||
CABixler
at 10:17am 06.26.23
2/617
Chicago winters tend to shut down the part of my brain that log's onto this group. Just logged in fo
|
||
spadaforaj
at 9:15am 06.26.23
4/582
Hi - my outboard typically gets in the way of raising my dingy (AL10) up to a reasonable height. and
|
||
solosailorwem
at 5:36am 06.26.23
0/618
Can anyone share the back-up techniques for lowering and raising the keel? Wally
|
||
RobAL
at 4:22am 06.26.23
0/345
I'm looking for a trolley for a Hunter 326 twin keel (not needed to be a full roadworthy trailer), a
|
||
fred1diver
at 7:02pm 06.25.23
20/1716
Hello all. Will be trying my spinnaker tomorrow morning, not going to lie, a bit stressed, never tri
|
||
poco505
at 8:54am 06.25.23
9/975
Hi guys, do you know the Portsmouth rating for Hunter26. Thanks
|
||
Centex
at 7:57am 06.25.23
7/2692
Going through a Merit 22, getting it ready to go back in the water. Since the boat has been sitting
|
||
Volkditty
at 7:47am 06.25.23
5/2167
Hello, sailors. Looking for a sanity check on tuning up the standing rigging on my San Juan 21 Mk1 t
|
||
drgbanks
at 6:48am 06.25.23
2/1048
Hello all, I'll be tipping my boat in my backyard today so I can work on the center board. Any advi
|
||
Sue n Brad
at 5:40am 06.25.23
5/634
|
||
arcadiahunter28
at 5:29am 06.25.23
11/2037
10 years ago I had a small disaster at sea. I was watching July 4th fireworks from offshore. When I
|
||
Kevy
at 6:42pm 06.24.23
16/2246
Heya! Our 2000 H320 is a great family boat, but sometimes the sailing leaves a bit to be desired (m
|
||
smokey73
at 5:54pm 06.24.23
9/1586
This is not a knock on Tides Marine Sail Track at all but just a caution to inspect your track for u
|
||
zinahewitt
at 3:57pm 06.24.23
1/341
Hi All, I hope your weekend/week is going well. I have a Dufour 34 1975. It has a water filter that
|
||
babadu
at 3:55pm 06.24.23
3/691
In search of a cushion or also a chaise lounge like a stadium seat back. For a straight bench of a r
|
||
Rich Stidger
at 3:23pm 06.24.23
75/7553
So this issue started in the fall of 2022. I discovered a small amount of diesel that was absorbed
|
||
mermike
at 12:15pm 06.24.23
9/1502
Greetings, We've escaped the shackles of labor and are heading for Victoria early next week. We're
|
ACR setup question
jssailem at 7:19am 04.30.25 Don't forget to fuse your ACR Here are BlueSea's thoughts. https://www.bluesea.com/support/article |
||
Thicker secondary filter o-ring and bleed screw gasket
kloudie1 at 7:15am 04.30.25 O-rings are standard sized using the ID and the cross section.. Since the part # has the "44" in it, |
||
Insurance assistance needed
DRhoads at 7:14am 04.30.25 Jim, What year is your 420? I have a 05 and will be there this weekend. I can take pictures of bat |
||
Thicker secondary filter o-ring and bleed screw gasket
skunther at 7:06am 04.30.25 I have noticed a very slight amount of fuel on the feeder line between the lift pump and filter hous |
||
Thicker secondary filter o-ring and bleed screw gasket
skunther at 7:00am 04.30.25 Can anyone confirm the appropriate ID for these o-rings? I purchased 3mm thick by 38mm ID, to provi |
||
Cleaning boat deck - recommended products and process
Project_Mayhem at 6:56am 04.30.25 The last yard I was at used brushes on brushes on little Milwaukee drills and Zep cleaner. Brushes s |
||
Thicker secondary filter o-ring and bleed screw gasket (3)
sailcapt340 at 6:43am 04.30.25 I just came from drilling out the hole for my remote mic on my boat, sorry I missed this posting, I |
||
Boat aground in Queensland Australia
shemandr at 6:09am 04.30.25 How do you "Sink" when you are hard on the rocks? |
||
Thicker secondary filter o-ring and bleed screw gasket (1)
colemj at 5:55am 04.30.25 The bleed screw has a seal. Yours may still be stuck to the housing. |
||
Boat aground in Queensland Australia
dLj at 5:49am 04.30.25 Must be the moon... That first story - their second rescue? Good grief.... dj |
||
I need a Solar System! Do you like yours?
colemj at 5:36am 04.30.25 I didn't even know Kyocera made panels. I'll look for them. Thank you for the response Kyocera |
||
I need a Solar System! Do you like yours?
colemj at 5:27am 04.30.25 I'm not seeing those prices so I'll keep looking. I also like the idea of bi-facial bc I assume re |
||
Hunter 290 throttle/ transmission cable
dlochner at 5:06am 04.30.25 Look on the cable jacket for the model number. Encoded in the number is the length of the cable. The |
||
Replacing a cutlass bearing
dlochner at 4:56am 04.30.25 The stern tube likely had a cutlass bearing as well as the strut. I doubt there were 2 cutless be |
||
Catalina 22 New Design - Dinette Table Size?
chipmonger at 3:17am 04.30.25 On my way to work, will look at this evening. Thanks again! |
||