smokey73
at 4:38pm 01.10.15
7/1574
Hunter 40.5 I am planning on installing my diesel generator in the starboard lazarette. For those
|
||
Guardian
at 2:57pm 01.10.15
3/860
Removal of Sheet Travelers I am doing a major Paint and repair on my boat and removing all deck fit
|
||
CanDoSeabeeS2
at 1:57pm 01.10.15
5/1140
Can Do here. I have a 9.2A and when the engine heats up there is steam discharging out of the exha
|
||
rockingham
at 12:17pm 01.10.15
7/2234
Just completed a 20 minute redo on my Montgomery 17 which has a 140# cast iron centerboard. Seems th
|
||
Bad Obsession
at 12:06pm 01.10.15
9/1473
I don't have a membership to Sam's Club or CostCo. I am curious if anyone else has a good source to
|
||
NiceBeny
at 10:41am 01.10.15
9/3239
Have levers engine and parallel, how and what is the best way to use these? ( it's not the same as t
|
||
Forestay Length (1)
PatTormey
at 9:34am 01.10.15
13/1726
My oDay 322 forestay is too slack, so Thinking I could tighten it some, I found that the turnbuckle
|
||
Gene Neill
at 9:08am 01.10.15
13/2316
My masthead light. I'm trying to find out what it's power draw might be, since it seems to deplete m
|
||
VF84Sluggo
at 8:47am 01.10.15
18/2222
Hey all, I'm a newb here - first post (and a new thread to boot) - and I'm looking at getting my
|
||
Fred
at 8:46am 01.10.15
2/745
I would love to see more pictures of dodger solutions and experience for H26? How to install a dodge
|
||
soireeiown
at 8:45am 01.10.15
2/891
I am trying to change my 2 blade propeller into a 3 blade propeller but I am having trouble finding
|
||
bobalu11
at 8:23am 01.10.15
3/1385
I am looking at buying an oday222. But it doesn't have a trailer and where is the anchor setup/lock
|
||
Bob 04 H260
at 6:36am 01.10.15
12/1831
I have a couple is places on my rudder where the bottom paint has chipped off showing the bare gel c
|
||
mrducks
at 6:04pm 01.09.15
25/3559
Need to do the copper paint very soon. Was planing to do the load off center trick to access under b
|
||
Cowpokee
at 2:24pm 01.09.15
4/827
I recently purchased a new 150% genoa and bought new line for the sheets. I tied the new line on wit
|
||
Sage34
at 2:13pm 01.09.15
0/837
Hi All, I've read extensively through all the previous threads about the Tierods shearing, the ma
|
||
eugenesdream24
at 1:55pm 01.09.15
29/4233
Hey everyone, I am in a pretty tough spot this winter as my boat had to stay in the water while I am
|
||
KZW
at 12:53pm 01.09.15
77/21796
There is a lot of discussion on swapping out the Sherwood G-908 raw water pump for the Oberdorfer N2
|
||
hotchki
at 11:34am 01.09.15
2/1288
Happy New Year! I'm considering removing and or replacing (after refinishing ) the teak hand gra
|
||
holdech
at 9:09am 01.09.15
10/1824
We are headed down tomorrow and plan to hook up with a few friends (mostly from the TSBB forum).
|
Help Identifying model
apell at 4:04am 06.08.23 that is a 6 (six) the letter B would be capitalized... Yes, my thought, too. I'm heading over th |
||
Help Identifying model
apell at 3:59am 06.08.23 Try checking in with the Mariner Class Association web site. We maintain an updated list of boats |
||
Help Identifying model
sailme88 at 3:45am 06.08.23 that is a 6 (six) the letter B would be capitalized... |
||
Help Identifying model
Will Gilmore at 3:27am 06.08.23 Try checking in with the Mariner Class Association web site. We maintain an updated list of boats a |
||
Hunter 49/50AC wiring for lithium conversion
artboas at 12:04am 06.08.23 Hi Art, Our system is planned at 600+ah of lithium and we would like to heat hot water and reduce |
||
Stainless Rub Strake Installation
Rick Webb at 9:09pm 06.07.23 My link to the drill bit didn't make it into my post. Second try Kobalt Magnetic Screwdriving Bit |
||
Help Identifying model
apell at 8:15pm 06.07.23 Exactly...I'm new to this site, but it was my perusal of the model list with identifying letter w |
||
Help Identifying model
apell at 8:11pm 06.07.23 The 20 with an added window and transom cutout is a decent guess, but even that was first built in |
||
What's next to be aware of ? (3)
Will Gilmore at 7:27pm 06.07.23 https://encrypted-tbn0.gstatic.com/shopping?q=tbn:ANd9GcQa4f1YSK0Wfbl1yYe18qDVlus9c8Ilai7mya_3lEzmHk |
||
Yanmar 2GM20Y won't run after replacing fuel lift pump. (1)
Ralph Johnstone at 7:20pm 06.07.23 If you determine your fuel pump is working you might want to look back at hidden air in the fuel lin |
||
Help Identifying model
Davidasailor26 at 7:12pm 06.07.23 The 20 with an added window and transom cutout is a decent guess, but even that was first built in 7 |
||
Best Chart Plotter Solution
Davidasailor26 at 7:01pm 06.07.23 Interfacing - Im not sure how to get all device to talk to OpenCPN, ie Seatalk, wind depth, Etherne |
||
Best Chart Plotter Solution
Screen Saver at 6:40pm 06.07.23 Thanks good to know. Yes one of my proffered options is very similar, but PC not Mac using 15.6" IP6 |
||
fuel gauge
Ralph Johnstone at 6:36pm 06.07.23 Will be testing it this weekend Thanks Rick Please follow up. The results would be interesting. |
||
Yanmar 2GM20F (1993)
Ralph Johnstone at 6:34pm 06.07.23 What is wrong with the water pump? An excellent question. I would expect the raw water pump on |
||
Newbie
High Current at 6:32pm 06.07.23 A couple of pointers. When we purchased our first boat, I attended a Power Squadron seminar, which |