Serving sailors online since 1997
 
 

Recent Topics

drewmacd at 8:19am 04.28.15
1/3070
I recently acquired a 12' O'Day Widgeon, circa 1970's, from a family friend. Interestingly, they ori
mlindberg1 at 7:19am 04.28.15
10/1795
The bolt that connects the tiller to the rudder is really sloppy and has a lot of play. Is there a f
bobcat30 at 7:11am 04.28.15
2/959
Trying to replace my 4 port gaskets. Cat Direct has them for $35 each. I thought that was pretty exp
braol at 6:31am 04.28.15
14/5702
So...after bleeding my engine until well after the cows came home I have progress, sort of. Now I h
Prussian at 5:52am 04.28.15
1/700
Dave, Thanks for your reply. The outboard motor is a Nissan 9.9 HP, 2 stroke motor, 2004 model year
EnginesForward at 2:18am 04.28.15
8/1280
I am not real computer literate. Can someone tell me how to load and post photos in answer to a top
c130king at 6:54pm 04.27.15
14/2475
Mine is cracked and leaking. Temp fix with duct tape. Can't find one on Catalina Direct. Any help
Burchards bounty at 6:38pm 04.27.15
12/1984
My husband got to our boat and the batteries were firecracker hot. Could lightening cause this? He t
Reidsair at 6:36pm 04.27.15
18/2661
I'm having trouble getting my Mac 26S to point to the wind if the wind builds. Tiller hard a lee and
maddotto at 5:57pm 04.27.15
2/879
Hello and thanks for any help. I am trying to find the original length of the backstay for a '91, 26
ben solomon at 5:56pm 04.27.15
9/1302
Hello, everyone. Has anyone replaced the clam shell vent for the holding tank vent? Mine is behind
alanmaki at 5:02pm 04.27.15
3/2191
What is the largest outboard motor I can put on my Columbia T-23?
Afrakes at 4:41pm 04.27.15
17/3235
Please be aware of scammers plying the for sale classified ads. Specifically Katty Martins7000@Outl
Sandy Feet at 4:30pm 04.27.15
1/822
We have a 2002 model year, Alder-Barbor Cold Machine I think it is CU100 . Uses coolant . The unit l
Macboy at 4:28pm 04.27.15
0/511
This is what I'm searching for for the C's. Thought I'd post this for others seeking similar for the
Prussian at 3:28pm 04.27.15
1/720
I recently purchased a Hunter 260 with a Nissan 9.9 Hp outboard. The shift, throttle control cables
iamaskier87 at 3:14pm 04.27.15
5/1277
Hello, I purchased my first boat, a 1981 Catalina 22, last summer in the water. During fall haul
2 OLD PIRATES at 2:29pm 04.27.15
16/2149
Hi All: I bet some of you northerners are biting at the bit to get those sails up. Got a ques
Syversens at 2:28pm 04.27.15
2/859
Hey all, I have a Beneteau 361 and many years ago I put a spinnaker pole a friend gave me on the
chrisrezba at 2:09pm 04.27.15
8/1314
Hello Hunter Forum Guys and thanks for all your help. I just splashed my 1st Big Boat and I did it i

Recent Replies

2gm20f water heater circuit
JoeWhite at 5:30pm 11.03.23
Yes. Take a hose connect from one to the other at the engine.
Its funny Friday!
Kermit at 5:29pm 11.03.23
Kermit, here's my boat book on the coffee table. awmill cut the top and bottom flat but when we pul
Oday keel
Yoho Yoho at 5:22pm 11.03.23
Thanks for the info. That makes sense. No picture because I am probably not going to get this boat
Oday keel
kappykaplan at 4:41pm 11.03.23
The fin keel on this boat has a drain plug near where the keel is fastened to the boat. It is poss
Rebuild of high pressure fuel pump for Yanmar 3GM30F
Tally Ho at 4:12pm 11.03.23
2595 Not THAT many hours, my old 2GM20F has over 2000 hours. I hope you can get it sorted out (a
MaxProp prop   (1)
Tally Ho at 4:09pm 11.03.23
Thanks for the replies. I went over the recommendations from PYI and FoF again, and PYI is recommen
Rebuild of high pressure fuel pump for Yanmar 3GM30F
Alan Gomes at 3:51pm 11.03.23
Update: apparently there is also significant scoring on the nozzle pins of two of the three injecto
H50 master cabin headliner ceiling
artboas at 3:50pm 11.03.23
I believe that @artboas has posted on this, but couldn't find it. I'm attaching a link to a YouTub
Engine Sensor ID
DyverDown at 2:50pm 11.03.23
From the yanmar parts catalog it looks like you are correct looking for part number 127610-91350.
MaxProp prop
jssailem at 2:48pm 11.03.23
I was going to say (from memory in talking with WestbyNorth) 10-15% OF PROP DIAMETER. Then I though
MaxProp prop
dlochner at 2:43pm 11.03.23
The distance between the end of the prop and the strut should be about 1 shaft diameter, but it is n
Rebuild of high pressure fuel pump for Yanmar 3GM30F
Tally Ho at 2:35pm 11.03.23
How many hours on your engine? Greg
Thru Hull Replacement?
Crazy Dave Condon at 2:27pm 11.03.23
As a former Hunter dealer in North Carolina, I can understand it is expensive to haul out and I con
Thru Hull Replacement?
Tally Ho at 2:24pm 11.03.23
MaxProp prop   (2)
Tally Ho at 2:16pm 11.03.23
Interior Wood
Siamese at 2:16pm 11.03.23
I'd oil it. Wouldn't use varnish, but I might use a water based poly product. I would consider pain
Rewiring masthead and forward steaming light   (1)
rgranger at 1:57pm 11.03.23
after it somehow got smashed against a piling the first month I had my boat. Could have been worse.

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.