Serving sailors online since 1997
 
 

Recent Topics

C Jones at 6:09pm 07.12.15
5/2678
Anchor roller on a h23? Finished this morning Any one have a picture of a anchor roller on a h23? I
betzhunter at 6:04pm 07.12.15
11/1752
I can't seem to find out what the water pressure should be at 3/4 throttle on my 3gmf yanmar. I wou
Veraneo at 5:30pm 07.12.15
20/4114
Hi, Did anyone experience problem with their Adler/Barbour fridge? I am getting the error cod
Delezynski at 3:27pm 07.12.15
32/10690
Hi all, Jill and I are planning on cruising the Bahamas in the future. We are looking at all of
catapultdude at 3:00pm 07.12.15
19/1719
Me and my wife have been looking over the last few weeks at sail boats. We looked at a Hunter 34', 1
Pat at 1:04pm 07.12.15
3/1504
We had a bit of back-up in the head for a couple of weeks but this has been repaired. I found the
piedpiperIII at 12:18pm 07.12.15
3/937
My boat has no grates, cat direct offers screw on type. What have you used??
bgbailey at 12:17pm 07.12.15
11/1622
I've tried everything I can think of to get rid of the pesty leak in my forward v-birth locker. He
Richard19084 at 11:59am 07.12.15
5/1191
The threaded connector drain on my holding tank has developed a leak which one can imagine did not
John T1594 at 11:35am 07.12.15
6/1168
I have a 2000 H340 with the full complement of factory installed monitors, sensors and instruments.
caguy at 9:37am 07.12.15
4/1125
This is what I am getting on my Surface Pro # with Win 8. Not sure is it is my puter or the new sit
FunCo at 9:19am 07.12.15
17/7492
I see some post of other people with squeaky wheels but no real answer given for the problem. I thou
planoron at 7:54am 07.12.15
1/793
So with all the rain this season and especially the amounts we received, I had a few small leaks ar
Kermit at 5:06am 07.12.15
76/10752
http://teespring.com/floats#pid=2'cid=6046'sid=back
drester228 at 5:03am 07.12.15
11/1727
Hope someone can help. Left boat with dry bilge, returned 3 days later with half full bilge of dirty
Andreas7699 at 1:24am 07.12.15
3/1041
Has someone fitted a furling asymetrical spinn on a H 36. I would like to hear from you as i plan to
Syversens at 9:22pm 07.11.15
10/10103
Hey all, so this isn't as much a question as a finding. After months of research, trial and error I'
MaryEllaRose at 8:45pm 07.11.15
6/1479
Can anything be done about weed build up on the keel cable? Today I swam under the boat and removed
Cabin table   (1)
D Renard at 8:05pm 07.11.15
4/1121
I have a Hunter 260. I would like to lower the cabin table so the seat around the table can be used
TortugasRoyal at 7:53pm 07.11.15
13/6647
Goal, eliminate expensive retail instruments including displays. I'm giving this a try. Has wind. S

Recent Replies

How are lines run to cockpit for 150% genoa from roller furler?
David in Sandusky at 8:18am 12.02.23
Lots of good advice already. First, I would say that a roller curler for your foresail is a great i
How are lines run to cockpit for 150% genoa from roller furler?
shemandr at 7:54am 12.02.23
Sailboatdata.com shows the 26X as a fractional rig which normally wouldn't suit a 150%. If you want
Any clever ideas on how to monitor the level in waste holding tank?
Peggie Hall HeadMistress at 7:31am 12.02.23
I have the SCAD system. I had to install their probe because I have a metal tank. What makes their
Seeking a precise pattern for a Hunter 260 jib
Crazy Dave Condon at 7:02am 12.02.23
@Crusty Ol Salt I concur with you recommending local sail lofts; however, there are many marinas an
Any clever ideas on how to monitor the level in waste holding tank?
Justin_NSA at 6:55am 12.02.23
I have the SCAD system. I had to install their probe because I have a metal tank.
Priming AC/heat pump.
Ted10028 at 6:50am 12.02.23
I don't have a bypass kit for my hot water heater either. I simply run all hot and cold water lines
Priming AC/heat pump.
TimFromLI at 6:48am 12.02.23
Another method is to use use a pony pump to pump the antifreeze through the thru-hull outlet from ou
Electric Motors
Scott T-Bird at 6:43am 12.02.23
How are lines run to cockpit for 150% genoa from roller furler?   (1)
rgranger at 5:57am 12.02.23
I used this fairlead to run the lines outside the stanchions
Priming AC/heat pump.
Davidasailor26 at 5:55am 12.02.23
The 4 gallons is probably overkill. The first couple are what I recover from my water heater after w
Priming AC/heat pump.
Ted10028 at 4:15am 12.02.23
thanks. wow 4 gallons seems like a lot.i have no idea how many gallons my ac/heat pump requires for
Dodger Needed
FastOlson at 10:12pm 12.01.23
Have you thought about building a hard dodger? Lots of YouTube videos on howto and I think would be
Dodger Needed
Michael Davis at 8:59pm 12.01.23
Have you thought about building a hard dodger? Lots of YouTube videos on howto and I think would be
Any clever ideas on how to monitor the level in waste holding tank?
sesmith at 7:15pm 12.01.23
Mine has a monitor strip on it that's pretty useless. A tap with a calibrated knuckle is more accur
Dodger Needed
sesmith at 7:04pm 12.01.23
That price sounds very high to me, but you're in the state of California, where all parts of the pro
Hunter 410 Temp Reading High
shemandr at 6:32pm 12.01.23
Maybe the engine is running hot - that's what the temp gauge is telling you. I mean why blame the g
Catalina 310 battery wiring question   (1)
Ralph Johnstone at 5:33pm 12.01.23
Thar she be : which is what you paid for. a artillery on board. That's why the heavy wiring.

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.