New ports (2)
TENACITY CS36T
at 5:06pm 05.22.15
12/2463
http://i326.photobucket.com/albums/k440/pmcneilvw/TENACITY%20CS36T/image.jpg14_zpswzbvdyxl.jpg Repl
|
||
Mike Kane
at 4:57pm 05.22.15
1/691
I am looking a a hull cleaner to remove waxy buildup from the winter canvas cover and other water st
|
||
Davefromoregon
at 4:29pm 05.22.15
0/551
The spray nozzle needs to be replaced. It basically looks like the nozzle you would find on a kitche
|
||
John12427
at 2:43pm 05.22.15
3/1428
anyone know good rig tuner? have hunter 356 boat and was shipped to house of boats rockport texas
|
||
GorillaToast
at 2:39pm 05.22.15
12/2003
Defender sold me the flanged seacocks, but doesn't carry the screws. WM has them, in packs of 300!
|
||
John12427
at 2:25pm 05.22.15
1/737
Am moving boat down to mustang island have to have arch re-installed anyone with any good advice rig
|
||
chusansail
at 2:23pm 05.22.15
4/815
I have had the hose on the stuffing box on the rudder shaft replaced repacked the stuffing box on th
|
||
DAVA390
at 1:35pm 05.22.15
0/1161
Anyone who would like to meet up,let me know, or watch for Precision 23 Breakin' Wind.
|
||
4arch
at 1:11pm 05.22.15
7/1292
|
||
burnswelds
at 12:49pm 05.22.15
3/717
Hello all, I replaced my old PVC mixing tee with a brass one . Now I cannot get cool water to flow t
|
||
morganoutisland
at 11:00am 05.22.15
2/802
Hello all, I'm about to install 5 new gray portlights. The outside of the ports stick out about 4"
|
||
Bob4203
at 10:47am 05.22.15
9/1715
I have to replace my hot water heater in my 1988 Mark II. The dimensions of this Seaward (Atwood) si
|
||
blueskysailingclub
at 9:45am 05.22.15
2/1536
Looking for the manual for a 23' coronado. I have seen it before. Can you help? Henry
|
||
Leeward Rail
at 9:37am 05.22.15
305/43954
Hello all, At the suggestion of other forum members, this is a thread that will document the proj
|
||
tj15830
at 6:59am 05.22.15
1/681
I just bought a 1986 MaGregor 25. The port lights had one big piece of acrylic across both light on
|
||
Brian D
at 6:52am 05.22.15
1/3478
From a post on SSCA Forums ------------------------ New FCC Radio License Printing Procedure by
|
||
slowdog
at 6:52am 05.22.15
0/881
Looking for a gas spring part#173271 for a OMC motor bracket
|
||
FasterHorses
at 5:32am 05.22.15
8/1540
I need advice and in a hurry..... Our '84 O'Day 39 needed to have the forestay disconnected in or
|
||
st nick
at 5:03am 05.22.15
1/840
i have seen a Hunter with euro style black plastic and black windows mounted in that space ! Can a
|
||
Apex
at 4:38am 05.22.15
6/1345
Sorry for those that have been through this over-and-over, but looking for specific info on wiring s
|
Need advice for running backstay with staysail on H49
Terry Cox at 12:39pm 02.12.23 There are former Hunter Marine technicians available on this site to pose that question. Most of the |
||
Seacock question on a 1981H33
rgranger at 12:38pm 02.12.23 Putting a sea cock on a scupper would mean an obstruction to quickly dumping water should a wave was |
||
Seacock question on a 1981H33
rgranger at 12:35pm 02.12.23 Also, is that the quadrant next to it? That lower post mounting looks suspect to my untrained eye. |
||
Seacock question on a 1981H33
Terry Cox at 12:32pm 02.12.23 Different model boat, but both our cockpit drains have through hull valves. Plenty of room on our bo |
||
Mk III aft locker hatch question (2)
stevenhagberg at 12:32pm 02.12.23 I think from your description our boats may be very different. My propane tank is on the port side. |
||
Rear pulpit modification
Terry Cox at 12:22pm 02.12.23 To keep my pulpit rail aesthetically clean looking, I would likely go with a matching set of these: |
||
Rear pulpit modification
Caboteur at 11:50am 02.12.23 I had ss wire and pelican on my c&c landfall 38. There were angle braces to support when open. It wi |
||
Prop seal change on Honda BF50A
jssailem at 11:48am 02.12.23 take my chances for another season. I would get the shaft threads cleaned. The nut and the shaft |
||
Newbie installing a new thru hull transducer
Ward H at 10:57am 02.12.23 Good question. The inside surface of the hull is probably not completely flat or smooth. Thickened |
||
New autopilot
jssailem at 10:44am 02.12.23 The EV-100 install manual shows the wire install from the motor to the ACU. You route the control wi |
||
Newbie installing a new thru hull transducer
Ward H at 10:43am 02.12.23 @mforum You probably did but it's worth asking: Did you try the new depth sounder tube in the existi |
||
Need advice for running backstay with staysail on H49
jssailem at 10:26am 02.12.23 You can set up the staysail rig. Go out on the water and observe the contrary bend created in the m |
||
Rear pulpit modification (1)
fred1diver at 10:22am 02.12.23 212939 This is the only pic I have at the moment of the aft pulpit |
||
Seacock question on a 1981H33
jssailem at 9:41am 02.12.23 The water line is the key. Putting a sea cock on a scupper would mean an obstruction to quickly dump |
||
Spades &. Quick Connect terminals
Maine Sail at 9:33am 02.12.23 Thanks @Maine Sail - good to see you writing again and sharing your knowledge. I am not an electr |
||
Seacock question on a 1981H33
Davidasailor26 at 9:20am 02.12.23 Tricky spot. Adding a seacock would take so much space it might be hard to still connect the top of |
||