|
K5 Sails
at 2:36pm 03.13.24
5/1312
I'm heading out to look at a1987 O'Day 272 LE . It caught my eye because it's trailerable, and pres
|
||
|
John12643
at 1:09pm 03.13.24
2/735
|
||
|
azambella
at 11:55am 03.13.24
13/1955
Has anyone pressured up the cabin to find deck leaks? how did this go? Any suggestions ?
|
||
|
azambella
at 11:54am 03.13.24
1/503
Our 82 Hunter 33 has the carpet on the inner hull. What is best way to do this? Thanks for any inp
|
||
|
azambella
at 11:52am 03.13.24
9/1999
I want to descale our 2GM. I can see lots of deposits inside the motor when I pull the thermostat.
|
||
|
Fudsdad
at 8:22am 03.13.24
1/499
Anybody know how I can source a replacement car assembly for my 36? The roller is all I need in fac
|
||
|
Dr. D
at 7:47am 03.13.24
4/1051
I'm considering ordering a new mainsail. My boat has in mast furling. The current mainsail has three
|
||
|
bob45
at 7:00am 03.13.24
3/1094
Any tips or tricks to unstick a Marelon seacock? Preferably from the outside. The boat is out of the
|
||
|
The_Sailing_Pelican
at 1:40am 03.13.24
11/1039
Ok.... Here we go again... Since buying a used engine proved to be caos regarding opinions, well wit
|
||
|
dlochner
at 7:19pm 03.12.24
3/1099
Some exciting sailing in Hawai'i. iXtR0sszr_A
|
||
|
mjsb
at 4:20pm 03.12.24
9/1169
I am planning to install a Raymarine rudder sensor on a Hunter 31. Has anyone installed one before?
|
||
|
Ted10028
at 2:09pm 03.12.24
34/5129
Bumped into a guy on the docks today who said my battery compartment should be vented. He said when
|
||
|
PK123
at 9:06am 03.12.24
19/4762
In theory yes, look at the depth, add the freeboard, adjust for tide and weather and conditions, set
|
||
|
JamesG161
at 5:40am 03.12.24
5/1286
HK6y8DAPN_0 Jim...
|
||
|
redege
at 1:35am 03.12.24
6/2039
Hi! Someone ran into my bow/anchor and the aluminium? stem head snapped and broke on my Oceanis 351.
|
||
|
Hello Below
at 7:57pm 03.11.24
14/1545
A screen capture from a Facebook post. This little town is about a 25 minute drive from where I was
|
||
|
chelsabella
at 7:17pm 03.11.24
4/772
I am replacing my spruce spreaders with CD Aluminum. Having difficulty removing the bottom bolt on t
|
||
|
gouldx
at 7:02pm 03.11.24
26/3747
|
||
|
claudesapp
at 6:21pm 03.11.24
12/2830
I have a 1989 Capri 18 and the next project is to upgrade the electrical. Owned her for a few years
|
||
|
NYSail
at 4:52pm 03.11.24
5/681
Hello all So I have 4 trojan T 125 6 volt batteries, 12 volt system. Want to take them off the boat
|
|
Last hurrah for 2025 but what a great season it's been!!
jssailem at 12:10pm 10.21.25 Oh, the enclosed waters of a beautiful Oregon lake in the Cascades. Which one? |
||
|
Best way to fill small wood rudder crack? (1)
jssailem at 12:01pm 10.21.25 I would insert BowTies to hold the crack permanently. The glue/epoxy approach will eventually fail. |
||
|
Axle fell out
BigEasy at 11:46am 10.21.25 I hadn't thought about the SC Beneteau place. Thanks BigEasy! Doc, I checked on the Beneteau |
||
|
Parts found under Yanmar 3YM30
Hunter 36 Dave at 11:24am 10.21.25 Sorry. It was not a test and I can understand the humorous side of it. However, I was afraid that I |
||
|
Sleeping offshore
capta at 10:59am 10.21.25 When crossing, one is more likely to encounter ships than others sailors. Radar and AIS with alarm |
||
|
Centerboard/Swing Keel Removal - Hunter 240
rgranger at 10:44am 10.21.25 There are a lot of tricks to getting a boat off of the trailer. I've read several and I've tried a |
||
|
Replacing single rusty keelboat
Ralph Johnstone at 10:28am 10.21.25 Good memory @Indysailor , and bad memory on my part as I put in a few thoughts to that post back in |
||
|
Sleeping offshore
dLj at 9:58am 10.21.25 Your last sentence is true. Perhaps because of my CG experiences, I tend to look at why and how acc |
||
|
Sleeping offshore
Don S/V ILLusion at 9:38am 10.21.25 I'm not so sure I agree with illegal as, to the best of my understanding, in international waters, |
||
|
New Cal 29 owner rigging questions
Tally Ho at 9:33am 10.21.25 And finally, the motor (an inboard gasoline Atomic 4) occasionally conks out after 20 minutes or so |
||
|
New Cal 29 owner rigging questions
jssailem at 9:10am 10.21.25 Is there a way to cut through the corrosion (presumably oxidized aluminum) without damaging the cas |
||
|
flushing long shaft outboard tilted
Project_Mayhem at 8:56am 10.21.25 Not all motors will run while tilted. I have one that wont start unless somewhat level |
||
|
The "Gambits"
JamesG161 at 8:39am 10.21.25 Pawn to Queen 4 is my opening! Fun game where Bishop power is revealed :cool: Jim... |
||
|
The "Gambits"
jssailem at 8:26am 10.21.25 Maybe. But when it develops, you might as well concede and move on. Kicking yourself, of course. |
||
|
Invest 98L (3)
jssailem at 8:21am 10.21.25 "Something wicked this way comes." Perhaps the lack of storm excitement this year has the internet |
||
|
Axle fell out
Dr. D at 8:03am 10.21.25 I hadn't thought about the SC Beneteau place. Thanks BigEasy! |
||
|
Sleeping offshore
Will Gilmore at 7:13am 10.21.25 But, ~5nm visibility to the horizon and making 5knots is only an hour to anything you see and that |