jimmcgee
at 12:55pm 08.10.15
9/2418
We have a manual Jabsco head in our 95 Catalina 30 that is working fine (touch wood), bu the wife is
|
||
JK_Boston_Catalina310
at 12:24pm 08.10.15
3/2962
The poor steering system on Smitty had been neglected. According to the manual from the manufacture
|
||
njlarry
at 11:57am 08.10.15
17/3973
I would like to add ventilation to my engine compartment for better air flow to the engine and the r
|
||
FlimFlamII
at 11:27am 08.10.15
4/1116
Does anyone have an idea on how to remove the forward screw in the attached photo? The screws are n
|
||
repawn
at 11:25am 08.10.15
13/1176
Hi all, I removed my outboard mount from my Oday 22 to replace the backer -the old one was rotting.
|
||
Graycruiser
at 11:14am 08.10.15
1/1049
On our 1994 Catalina 320, the blower is on the output side of the air flow. Originally, it was wired
|
||
pmb
at 11:04am 08.10.15
5/880
I am looking to buy and install a watermaker. The watermaker that I am currently looking at is an It
|
||
a65sailor
at 10:55am 08.10.15
1/572
I wondered if anyone knows the specs on the main AC breaker and where I can get a replacement. Than
|
||
ArcticFarx
at 10:22am 08.10.15
12/1385
I have a H260 with a water issue. Last season we had quite a bit of water in the bilge after a road
|
||
jenunn01
at 9:49am 08.10.15
1/626
I need to replace the engine temperature gauge and the hours meter on the Seaward control panel from
|
||
jenunn01
at 9:33am 08.10.15
0/457
I need to replace the engine temperature gauge and the hours meter on the Seaward control panel from
|
||
jeff356
at 9:26am 08.10.15
12/1897
Have a rigid boom vang an am curious how to adjust it to better trim the main sail. Currently the
|
||
Tim22
at 9:17am 08.10.15
2/766
i seem to have a leak originating from under the sea hood so am working up to removing it this weeke
|
||
Charitybull
at 8:14am 08.10.15
0/544
Hi, Fellow sailors. So, after finding out what happens when a 25 foot high branch hits a much ta
|
||
Catalina 27 Files (10)
philwsailz
at 7:16am 08.10.15
5/1768
I worked early on with Kent Nelson at the California Catalina plant to get as much information as po
|
||
lydiao
at 7:12am 08.10.15
7/1086
best lube My poor Cat 30 has been sitting at the dock neglected for about 4 years. Trying to bring
|
||
geek_guy
at 6:21am 08.10.15
3/985
Sometimes you have to wonder....... I replaced the throttle and shift cables. They are really ni
|
||
Bottom Stains (1)
SqPeg
at 6:18am 08.10.15
18/2090
What causes stains like these on a freshly waxed boat? We paid to have it waxed on the hard last spr
|
||
geek_guy
at 6:15am 08.10.15
5/1221
I have read and think I understand the basics of battery combining. However the previous owner of m
|
||
Leeward Rail
at 5:26am 08.10.15
2/839
I remember seeing a DIY thread or blog post or something, about a rebuild kit for the outboard motor
|
Inverter Bilge query
tfox2069 at 10:09am 03.08.23 Scratching my head at the setup. Typically a boat has with both a manual and automatic bilge pump. |
||
1984 Hunter 31 - Cast Iron Keel Rust
anelso29 at 10:04am 03.08.23 Hello everyone, I just wanted to provide an update on my progress. I have recently purchased some I |
||
TOO MUCH WIND?
rgranger at 10:02am 03.08.23 Wow! I guess a little more girth in the bow would have helped her stay on her feet. |
||
TOO MUCH WIND?
stickinthemud57 at 9:59am 03.08.23 When the helmsman hits the shroud on the way down. OOF! |
||
Inverter Bilge query
DArcy at 9:42am 03.08.23 If I was in a situation where I needed to run an 1800 GPH pump I'm not sure I would want to rely on |
||
Inverter Bilge query
JohnShannon at 9:41am 03.08.23 It is likely a less efficient system than a DC 1800 pump the same water flow your batteries die so |
||
Spinnaker in top pulley-is it a concern?
PaulK at 9:40am 03.08.23 If your crew is strong enough to pull the halyard shackle into the sheave and jam it there, send him |
||
CG vessel renewal
Terry Cox at 9:35am 03.08.23 We've received a multi-year option in the past, not from the CG, but from an agency that acts on the |
||
Replacement AC brand advise
karellen at 9:17am 03.08.23 A local to me Boat AC person recommended MarineAire and against a newer Dometic system. I do like |
||
In search of the driest bilge possible
Timm R Oday25 at 9:13am 03.08.23 Keeping the bilge dry has proveed to be an exercise in patience . Our boat spend the summer on a moo |
||
Ice Box Lid Hold Open
Cat 310 #1 in GA at 9:11am 03.08.23 It looks like the one you placed in the fridge is not extended to the locking part of the hold open |
||
Ice Box Lid Hold Open
Cat 310 #1 in GA at 9:10am 03.08.23 The ones you purchased from Catalina Direct are they Prt# Z4237 I believe so. |
||
Rutgerson clutch maintenance
LloydB at 8:57am 03.08.23 only took a short time to find this video and the guy says torx not hex fyi youtube.com/watch?v=xTZS |
||
Spinnaker in top pulley-is it a concern?
dlochner at 8:45am 03.08.23 Spinakers are typically flown from an external block on a mast crane, a part of the masthead from wh |
||
A story of the engine that could.... Then didn't
jssailem at 8:11am 03.08.23 GOOD QUESTION! Still too early know the results or how to answer the question. I feel good about t |
||
In search of the driest bilge possible
Peggie Hall HeadMistress at 8:05am 03.08.23 A dry bilge requires a bit of manual labor: A shop vac and/or a sponge and a bucket after every wee |