cookcwayne
at 3:37pm 08.22.15
5/691
anyone know what size the O'Day 27 takes and where to locate one Previous owner replaced steering a
|
||
hensonrick5
at 2:55pm 08.22.15
13/9128
I'm brand new to sailing and got a free Sun Cat that has been swamped. I have it cleaned up and sai
|
||
plorette
at 1:33pm 08.22.15
7/1120
I have had two instances where I have motored out to sail, and when I attempt to restart after a sho
|
||
sandiegosailor99
at 9:53am 08.22.15
4/1097
Does anyone have any experience with minor blistering in the gelcoat of a large Hunter? I believe
|
||
nctxia
at 8:35am 08.22.15
6/1262
I am installing MRBF fuse blocks on my battery. Does anyone know what size fuse (they come from 30
|
||
woodster
at 7:32am 08.22.15
7/1357
i was in Long Beach Ms on Wednesday looking at docks and slips and while i was there came across a p
|
||
DockH
at 5:17am 08.22.15
9/2786
Any suggestions for treatments before and post pump out especially when passenger used it both ways
|
||
Jtoben
at 4:50am 08.22.15
2/884
The primary regulator on the CNG stove/oven has a bad diaphragm and spring. We replaced the seconda
|
||
Jtoben
at 4:12am 08.22.15
2/759
Looking for a primary CNG regulator. For a Gas Systems Inc, Hille Range stove/oven. I don't suppos
|
||
Karyon
at 9:33pm 08.21.15
5/972
last week we picked up our new to us H23.5, the former owner removed all the old striping and that s
|
||
kmbrink
at 8:27pm 08.21.15
3/1252
Boat purchased new 2004, original owner. For years, have noticed boat takes on some water in hull a
|
||
tom flatley
at 7:53pm 08.21.15
2/583
Just got a H-19-93 anybody know the dimensions of the main and jib? all I know is that the total
|
||
tom flatley
at 7:27pm 08.21.15
3/920
Hi So I just bought a 19- am in Rangeley Me- saw that there is a gino8644 who lives in Rockland Me a
|
||
sandiegosailor99
at 7:20pm 08.21.15
6/1192
Does anyone have any experience with taking down the mast on a Hunter 380 with roller furling for tr
|
||
riverbouy
at 7:11pm 08.21.15
6/1302
I need to replace my hot water heater but can't determine a method to remove it. I can disconnect i
|
||
Maine Sail
at 4:30pm 08.21.15
15/1632
This sure beats the 40 nm we did today in 50' to 100' vis.. http://www.pbase.com/mainecruising/im
|
||
Zed
at 4:26pm 08.21.15
21/5859
MY WIFE, the Admiral, has just informed me that her long term wish was to be able to propel our litt
|
||
Rich Stidger
at 4:25pm 08.21.15
14/2695
|
||
IH82BL8
at 3:44pm 08.21.15
2/922
The Yanmar service manual indicates the use of zincs on a raw water cooled engine. The 2gmf uses a
|
||
Don Guillette
at 1:55pm 08.21.15
15/4651
Mates: I get all kinds of questions by phone ' email from sailors all over the world. Normally, I ca
|
Newbie installing a new thru hull transducer
Ralph Johnstone at 10:02am 02.11.23 You do not need any cloth between the two but use one of the dense fillers for thickening. 406 Coll |
||
A story of the engine that could.... Then didn't
Hayden Watson at 9:55am 02.11.23 Yes. We are exploring the idea. Especially now that the PSS dripless has a reinforced silicone bell |
||
To boot or not to boot...turnbuckles
Sail22Capri22 at 9:49am 02.11.23 Was thinking of getting the wrap pins for my Capri 22 they work ok? |
||
Stale Forum
jssailem at 8:41am 02.11.23 Technology is sometimes baffling. Search out a 12-15 year old they are likely to know the answer and |
||
A story of the engine that could.... Then didn't
JamesG161 at 8:40am 02.11.23 The improvement in the bellows is what nudged me to the PYI product. 10 year warranty. However ins |
||
A story of the engine that could.... Then didn't
jssailem at 8:37am 02.11.23 There are many options. Difficulty is filtering the marketing from the performance. Looked also at t |
||
A story of the engine that could.... Then didn't (1)
JamesG161 at 8:33am 02.11.23 Especially now that the PSS dripless has a reinforced silicone bellows. Best seal to use for Zero |
||
1984 Hunter 31 Floor Board (1)
JamesG161 at 8:21am 02.11.23 bring it to his shop (in tact) You can also trace template of the FRP section too, on your boat. _ |
||
1984 Hunter 31 Floor Board (1)
JamesG161 at 8:17am 02.11.23 For reference... s the piece above. Jim... |
||
A story of the engine that could.... Then didn't
jssailem at 8:16am 02.11.23 Given the V drive and poor access are you going to go with a dripless seal this time around? Yes. |
||
1984 Hunter 31 Floor Board (1)
JamesG161 at 8:13am 02.11.23 This is back side of the Floor in my other post. ... PS: I will post another section that had wa |
||
mooring pendants
Alansails at 8:04am 02.11.23 I equate the lines to insurance and the value of what your boat is worth-would you use clothes line? |
||
mooring pendants
dlochner at 8:03am 02.11.23 Does the new ball does have a steel shaft that connects the pendant to the anchor chain? Mooring pe |
||
Newbie installing a new thru hull transducer
Hayden Watson at 7:59am 02.11.23 Makes sense. What type of consistency would be best for the epoxy? (mayonnaise, ketchup or peanut |
||
Meet your new Forum Administrator
Alansails at 7:52am 02.11.23 Much appreciation for all everyone who have had their hand on this, Takes alot of work that is somet |
||
Floor board replacement on a hunter 306
StephenM at 7:45am 02.11.23 The Deck in the cabin is meant to support weight. Not on my boat Jim... rt weight. Not on my |
||