MikeK2B
at 10:06am 09.20.15
15/1869
Hi everyone - I think that most of the plumbing on my Pearson 303 is original and in need of attenti
|
||
OS2Dude
at 10:00am 09.20.15
15/4245
We have a 1984 Catalina 30 with a fairly steep companionway ladder (3' or so) and an older dog in th
|
||
VelaFella
at 9:09am 09.20.15
11/2268
The engine is not charging the batteries (two 4D's) very well, as opposed to not-at-all. After tigh
|
||
davidmhull
at 4:41am 09.20.15
8/2938
Good morning. My main sheets are what I guess you would call conventionally mounted. That is to say
|
||
Ed D
at 4:39am 09.20.15
2/671
Hi Has anybody installed an electric toilet connected to the fresh water system on a Hunter 32 Vi
|
||
Neil01
at 4:27am 09.20.15
3/980
The only number on my plate is a 4 digit serial number- #1245. Does anyone know what year this se
|
||
MarkW11
at 8:49pm 09.19.15
0/813
I have a 1990 Hunter 27-2 and will be removing the mast for the first time. Can anyone tell me if I
|
||
jimclemons
at 6:49pm 09.19.15
0/7063
Recently inherited a restored Rhodes Ranger 29, any suggestions on where I would go to get a valuati
|
||
Fernando 15012
at 6:17pm 09.19.15
4/1764
We have our 1982 H30c out on the hard for a compression post support repair. Decided to take the tw
|
||
danners
at 4:43pm 09.19.15
3/1038
Just bought this sailboat. Where is the pump located?
|
||
Robert1224
at 4:36pm 09.19.15
5/1048
Ahoy, I am considering re-powering my 1979 Hunter 30 with a YSM12 to a Yanmar 2GMF. To those who ha
|
||
Dfisher
at 4:35pm 09.19.15
7/1992
Ive been chasing a severe vibration problem that doesn't allow my 1983 Hunter 31 to get to full RPM
|
||
pilotgene1
at 2:54pm 09.19.15
3/610
looking for the VHF antenna, thought it was on top of the mast, but didn't find it up there, antenna
|
||
Patrick Randall
at 2:35pm 09.19.15
1/539
Anyone fixed a H30T's joint between the engine cover/steps/"knives and forks box holder" and the hea
|
||
Terry in Naples
at 2:33pm 09.19.15
5/2012
My voltage regulator quit on me. I have an older Balmar hi power alternator set up with a voltage re
|
||
Patrick Randall
at 2:31pm 09.19.15
7/1002
Anyone know where to get the little moldings that stop you catching your toe on the end of the genoa
|
||
Joetech
at 12:26pm 09.19.15
6/1429
|
||
Windtherapy
at 12:23pm 09.19.15
16/1423
OK so as we all know the head room in an O'Day (or at least my 26') is just shy of 6 feet. I have b
|
||
Hugh Burton
at 11:44am 09.19.15
0/545
Getting our 26M ready for winter and I found a little H2O under the rear berth floorboards. Two spot
|
||
atrometer
at 11:14am 09.19.15
14/1319
On my 1976 22', I have an apparent leak somewhere in the area of the rear seat of the dinette. Wate
|
Must keep the mast from coming down (fiberglass)
dlochner at 12:44pm 02.18.23 I assume the fairing compound should be a hair shallower than the surrounding deck? Yes. Gelcoa |
||
Ouch!
Project_Mayhem at 11:51am 02.18.23 I pay about $2200 for a floating dock that I have to paddle out to. It's barely held together and ma |
||
Vitrifrigo BN100BT freezer temps
Hello Below at 11:36am 02.18.23 Thanks. So if we assume that the resting voltage for the house bank is around 12.7V when you took t |
||
Vitrifrigo BN100BT freezer temps
brockfromwa at 11:03am 02.18.23 One would think but apparently not. What is the voltages as measured right at each of the 2 compre |
||
Must keep the mast from coming down (fiberglass)
Project_Mayhem at 10:39am 02.18.23 I like butyl when I have fixtures with fasteners to adhere the parts together. When dealing with a |
||
Vitrifrigo BN100BT freezer temps
Hello Below at 10:37am 02.18.23 When the BD50F compressor cranks and pulls the voltage down on my system temporarily, wouldn't that |
||
26.5 hunter wing keel dimensions
Crazy Dave Condon at 10:17am 02.18.23 First you want a flat surface for the keel to rest on not that board pictured in the photo with tota |
||
Vitrifrigo BN100BT freezer temps (1)
brockfromwa at 10:11am 02.18.23 Thank you Captain Larry and Hello Below for your insight. Much appreciated. I've been intermittentl |
||
Replaced all my sanitation hoses (3)
Ralph Johnstone at 9:16am 02.18.23 "Lard tunderin' Jesus" I had no idea you were rebuilding the whole boat to install new sanitary line |
||
can you mix winch and winch handle brands? (1)
DaveJ at 9:09am 02.18.23 I use one of these on either side of my binnacle, the winch handle rarely is left in the winch. Very |
||
Hello to the community
Terry Cox at 8:33am 02.18.23 Texas, it's too freakin hot in the summer and too far from the ocean. Amen, Bro. |
||
protecting deck and nonslip
BigEasy at 8:32am 02.18.23 As DavidSailor mentioned, it is gel coat with nonskid pattern & grey color molded in. It is not pa |
||
Internet and telephone while off-shore in Canadian Pacific Northwest
Terry Cox at 8:08am 02.18.23 We've used Verizon International wireless service (Telus cell partnership) for years into British Co |
||
protecting deck and nonslip
Don S/V ILLusion at 8:08am 02.18.23 Once toured the Hunter factory in Alachua. The nonskid deck areas were all painted gray. If you feel |
||
Yamaha 30 - YSM12 diesel engine - need new stainless steel wet muffler (1)
Tally Ho at 7:10am 02.18.23 So, the engine is located in the V berth? That sounds like a strange place to mount an engine. Mu |