|
pmcrosta
at 10:24am 04.11.16
12/3034
Hello! I am the proud new owner of a 1994 Hunter 40.5. I'll probably have many, many questions as th
|
||
|
Sunday Sailor
at 10:09am 04.11.16
16/7776
I have a Hughes 26, which I bought and put a 9 hp 4 stroke in, which weighs about 70lbs. I don't hav
|
||
|
Cape Cod Sailing (1)
tootalltony
at 8:28am 04.11.16
2/1073
I have a Hunter 30-----keep her in Marion, Mass---I'll be launching her in mid May Anyone int
|
||
|
The Artful Dodger II
at 8:14am 04.11.16
4/2455
I have a 1990 Hunter 42 passage, I am trying to figure out how to repair the locking handles for the
|
||
|
SettleMeDown
at 7:22am 04.11.16
7/1398
Looking for car for US Spars mast on B473 to mount whisker pole. USSpars is no help. Anyone have an
|
||
|
Anchor locker (7)
flynhi4u
at 7:06am 04.11.16
38/7168
Every since we bought our boat I have wished it had bow storage for the anchor and rode. I think the
|
||
|
ryansk
at 5:44am 04.11.16
22/3642
Hi, I have a 1993 Hunter 27 with a Yanmar 1GM10 inboard diesel. It was starting and running fine and
|
||
|
Fortyeighter
at 5:37am 04.11.16
2/1177
Hi all. I'm about to launch a new to me Hunter 39. I've been getting to know the boat for the past f
|
||
|
onlinelee
at 11:06pm 04.10.16
2/1110
Hi all, Recently part of the mast step on my 2002 361 broke away ( see a picture in my other recen
|
||
|
pclarksurf
at 10:47pm 04.10.16
5/1117
its a floor again--
|
||
|
DianaOfBurlington
at 9:42pm 04.10.16
7/1763
I am looking for a boarding ladder that can be fixed-mounted (not removable), that folds down (not t
|
||
|
jleblanc31
at 7:18pm 04.10.16
14/1267
I said I was going to start this thread when I picked up the boat but I am working on boat stuff to
|
||
|
nveater
at 7:15pm 04.10.16
5/683
So I was going over the engine (yanmar 3gm30f) when I noticed two round holes on top of the fuel inj
|
||
|
SteveInMD
at 6:53pm 04.10.16
7/2527
I'm trying to do right by my new Yanmar 4JH57 and properly break it in. I have read the break in pro
|
||
|
SailShannon
at 6:31pm 04.10.16
2/913
Finally splashed our '89 C22 wing keel that I bought last fall. Rehab projects always take longer th
|
||
|
BlowMeAway
at 3:35pm 04.10.16
15/4180
121671 Just wondering if older Knotmeter transducers might be available for our older boats. My unde
|
||
|
Mechone
at 1:16pm 04.10.16
10/4295
Purchasing a 351 , currently sitting on a 6 pad cradle. The yard added 2 jack stands at back of boat
|
||
|
Osmosis
at 12:14pm 04.10.16
2/652
We will be trailering our Mac 25 up to Fairfax, VA and are hoping to find a Marina with dry storage
|
||
|
Bob 04 H260
at 11:36am 04.10.16
2/926
A friend just asked me about using a vented loop in the head discharge hose going to the holding tan
|
||
|
Ballast boy
at 11:32am 04.10.16
1/899
Hello, I posted something on the Hunter pages about a boat I am looking at. I haven't had much in te
|
|
Splicing sta set 8mm
jssailem at 8:41am 03.10.24 It was a bit of knowledge learned through failure. I tried. I failed. I discovered a better mouse |
||
|
Microwave on Hunter 306?
JamesG161 at 8:22am 03.10.24 The Microwave should be attached to the cabinet by at least one point, that is approved by their ins |
||
|
Splicing sta set 8mm (2)
jssailem at 8:18am 03.10.24 You identify the most difficult of the tasks when doing a splice with stay-set. This is compounded w |
||
|
Tohatsu Charging
Jacktar at 8:17am 03.10.24 Direct to battery, motor alternator has a voltage regulator on it. |
||
|
G-10 discs for thru-hull
dLj at 7:56am 03.10.24 Just not sure if there is a material comparability issue with Marelon sea cocks No material compa |
||
|
Microwave on Hunter 306? (1)
jdrutten at 5:02am 03.10.24 Mine came with an exotic Origo, but as jssailem noted, you could put whatever in there as long as it |
||
|
Microwave on Hunter 306?
jssailem at 4:25am 03.10.24 Congratulations on your boat acquisition. From your post I am guessing this is an older boat. As you |
||
|
Resurfacing cockpit ranger (2)
twodzusfittings at 3:24am 03.10.24 My first application of faux teak lasted total of three years before being removed. It was a cheap p |
||
|
How do you clean through hull while in water?
Ted10028 at 11:41pm 03.09.24 Pull the end cap off the heat exchanger and see if there is build up of scale on the tubes. I had a |
||
|
Should I put a 9.9 HP outboard on my 32' Catalina?
jssailem at 9:21pm 03.09.24 That may be his auxiliary. You can see the depth of the motor when down. Not very deep. Going throug |
||
|
How do you clean through hull while in water?
Allan12210 at 9:08pm 03.09.24 mine seems to overheat only at full throttle. I assume if the thermostat were not opening it would |
||
|
can someone tell me what these two hoses/ducts are for?
Ted10028 at 8:25pm 03.09.24 "If you move a few decades forward in time, the law was amended in 1982 to make a distinction betwee |
||
|
CONGRATS TO CRAZY DAVE CONDON.. OVER 10,000 HELPFUL MESSAGES
Crazy Dave Condon at 7:07pm 03.09.24 @Kermit never flew using that Beenie Weenie Propeller hat. Thanks for the reminder you green fro |
||
|
CONGRATS TO CRAZY DAVE CONDON.. OVER 10,000 HELPFUL MESSAGES
chuckwayne at 7:00pm 03.09.24 Thanks for all you help over the years, Dave, and congrats for setting a new milestone for Hunter Ow |