Serving sailors online since 1997
 
 

Recent Topics

Don Guhr at 7:19am 04.30.16
12/2505
Before starting the engine to remove anti-freeze I measured the starting battery voltage. It measure
RussianMermaid at 7:18am 04.30.16
1/1298
We are thinking of adding a swim platform to our 1983 O'Day 34. Did anyone do it? Could you suggest
Sailm8 at 7:13am 04.30.16
5/958
I am replacing the fixed windshield type window on my H 29.5 and have run into a problem. I bought
CatBoat59 at 6:59am 04.30.16
11/1491
Hello All, New member, first post ... I'm renovating a 1978 Oday 23, and am ready to attach the new
mrudman850 at 6:37am 04.30.16
10/2025
Got a 3 3/4 inch hole forward of the mast where a small solar ventilator fan (broken) was installed.
zigracer at 6:23am 04.30.16
1/770
What do you guys use for antifouling on plastic bow thruster props?
Doug J at 8:16pm 04.29.16
15/3417
I'm wondering if my main is bagged out. If I hoist it all the way tight and loosen the topping lift
Ward H at 7:41pm 04.29.16
24/5313
For the past two years I've been using dock lines that I spliced in eyes that fit my cleats well. Ea
Cincy020 at 7:40pm 04.29.16
5/1303
I have refinished all of my teak except the coamings. How do you remove these? Can't figure out how
MaryEllaRose at 7:24pm 04.29.16
2/721
I'm deep in the throes of installing a CF500 furler on the Rose. I purchased the kit from Catalina D
Ward H at 7:17pm 04.29.16
20/2430
My O'day never had a stern ladder. I've been planning on installing one since I bought the boat. The
Brian D at 4:35pm 04.29.16
7/1083
Here we go... mini cruise to Dana Point. Should take between 4 to 6 hours of leisurely sailing. Fore
wolfgangSeaLife at 2:33pm 04.29.16
2/645
Who knows the manufacturer of the Hunter Radar Arch with traveler on top? I want to have on custom m
MacBlaze at 10:07am 04.29.16
3/840
We have a 2003 Hunter 386 and it came with that stock weird solar panel just forward of the cockpit.
Polarisman at 8:08am 04.29.16
2/751
Hello all. I own an 83 Hunter 34. There is an issue with the bulkhead separating and my repair guy s
suttonwt at 8:02am 04.29.16
Cal
1/1107
So the new tiller arrived today for my 1968 Cal 28 and as I started to swap over the bracket I notic
Armyaviation at 7:14am 04.29.16
6/1982
i am stationed at Ft Rucker AL and Panama City beach is only about an hour away. I have a 21 ft Ame
smokey73 at 7:05am 04.29.16
15/1295
Does anyone know where this cockpit drain (at least I think that is what its supposed to be) is supp
Sacto Dave at 8:07pm 04.28.16
23/2195
One of 2130's POs had a cavalier attitude about ferrous fasteners, as photos depict in my previous p
Gene Neill at 6:44pm 04.28.16
16/8712
I currently utilize two lines run from one side of the mast, up through the reef cringles, and down

Recent Replies

Can a Plumbing Step Wrench be used on Through Hulls?
Project_Mayhem at 1:45pm 01.16.24
I've used 1-1/4" X 1/4" flat bar as per @dlochner above. Cheap and solid IF you've got the grinder
EVA Foam teak and holly flooring use.   (1)
PaulK at 1:14pm 01.16.24
What about putting it on the sides of the car?
Builders Certificate
BigEasy at 1:07pm 01.16.24
Has anyone on this forum had success in obtaining builders certificates from Beneteau? I requ
Display engine instruments on Raymarine C120 chart plotter.
tfox2069 at 1:01pm 01.16.24
I've been wanting to do this for years. Really well done.
'83 Oday 28' Keelbolt Torque and...
Bob_S at 12:56pm 01.16.24
Thank You!! Important information... Best, Bob
'83 Oday 28' Keelbolt Torque and...
dlochner at 12:53pm 01.16.24
For reference, Sabre suggests 90# for my 1 ?" bolts. Stainless bolts may gall if over torqued, which
EVA Foam teak and holly flooring use.   (3)
LaDonaMina at 12:15pm 01.16.24
Here is a closeup of the aft cabin with one of the cushions out. Also the Sea Ray with the machine c
Insurance question
jssailem at 11:54am 01.16.24
Insurance question
Hello Below at 11:41am 01.16.24
Can a Plumbing Step Wrench be used on Through Hulls?   (1)
Ralph Johnstone at 10:51am 01.16.24
Actually, I don't think this step wrench would work for holding on to thru hulls. cessary to ensure
Display engine instruments on Raymarine C120 chart plotter.
joelm100 at 10:42am 01.16.24
Thanks for that summary, and agree with BarryL: nice installation. I'll commit! (want to loan you
Builders Certificate
rgranger at 10:35am 01.16.24
A similar question appeared on another thread a few months ago... here.... https://forums.sailboato
Insurance question
LaDonaMina at 10:35am 01.16.24
Named Storm Damage - All bets are off, Furgetaboutit, No way Jose, Read the Bold Print! My boat w
Bottom Streaking
Project_Mayhem at 10:33am 01.16.24
I don't blame you for asking. Also a chance thru hulls have developed leaks after sitting for long
Can a Plumbing Step Wrench be used on Through Hulls?
Ralph Johnstone at 10:29am 01.16.24
At that price, it wouldn't be worth making one out of a pipe I've used 1-1/4" X 1/4" flat bar as
Insurance question
LaDonaMina at 10:29am 01.16.24
I am not sure how it works in your marina, for mine I have to provide a certificate of insurance to
EVA Foam teak and holly flooring use.
Ralph Johnstone at 10:25am 01.16.24
I can take a photo of what I did in the aft cabin and post it here. We're waiting.
Insurance question
Ralph Johnstone at 10:20am 01.16.24
I am not sure how it works in your marina, for mine I have to provide a certificate of insurance to
Insurance question
LaDonaMina at 9:29am 01.16.24

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.