Gunni
at 3:26pm 01.07.16
1/1980
S-L Horizon Express (2003). Needs a motor (sold here), and a control solenoid. 900 lb capacity, ge
|
||
toliver
at 1:29pm 01.07.16
32/7632
I want to replace a 35 yr old raw water engine intake gate valve (it is just a "screw on" type thru-
|
||
Mike H.
at 12:36pm 01.07.16
16/5861
Looking at purchasing a 1978 - 1980 Swift 40 Ketch. They were designed by Sparkman ' Stephens and b
|
||
Benny17441
at 12:26pm 01.07.16
4/719
Phil, I'm not being allowed to post and I'm getting this message, "Please read guidelines before pos
|
||
Squidd
at 11:52am 01.07.16
14/3533
I just recently purchased a PVC Dinghy.. Whats a good way to attach state registration numbers and
|
||
Collin
at 11:24am 01.07.16
0/692
Does anyone know the V-berth and aft cabin dimensions of a 2008 Hunter 31, or know where I can find
|
||
Casagf66
at 10:32am 01.07.16
7/1821
Hello again sailors, So my next step in renovating my new 1989 jeanneau 42 voyage will be to start
|
||
obdoor
at 1:28am 01.07.16
19/4870
I'm looking to buy new jacklines for my 1987 Pearson 33. Any suggestions?
|
||
RAD88
at 10:28pm 01.06.16
5/4052
I need a little help from the mechanics and Yanmar owners on this one. I'm sure it is possible but i
|
||
Christophe
at 5:02pm 01.06.16
17/3932
What is the best type of grease or lube for a single speed winch like a lewmar #7?
|
||
29palmsailor
at 4:27pm 01.06.16
12/3712
I have a 2000 Hunter 460 weight all Chain Rode and Anchor. Has anyone moved their rode out of the v
|
||
prroots
at 2:43pm 01.06.16
44/13999
I'm considering the purchase of one of the subject boats and would like to find diagrams showing how
|
||
RunTimeError
at 2:33pm 01.06.16
11/2721
I have been looking at a 77 O'day 20 of the newer design with the fractional rig and the absence of
|
||
Marc14857
at 1:26pm 01.06.16
3/582
I'm planning on adding an AIS transponder to my older RayMarine network. I currently have ST60 Instr
|
||
Cainsoccer
at 12:35pm 01.06.16
14/1389
I'm servicing the kick up rudder on my '81 C22. After getting the corroded center bolt out, I pulled
|
||
Sean Sexton
at 11:21am 01.06.16
5/1732
Anybody out there know what the headroom is for a mark I Cal 30? So far, I've only found references
|
||
Rodd
at 4:51am 01.06.16
22/2302
Happy New Year to Maine and the Group! About a year ago we had a thread regarding how to install a
|
||
obdoor
at 4:35am 01.06.16
5/2297
any and all advice is appreciated, what are my choices for rejuvenating or cleaning my yanmar heat
|
||
Mike H.
at 8:53pm 01.05.16
2/1134
We're in the market for a new boat. What can you tell me about the Sparkman ' Stephens, 40' Center c
|
||
Terry Cox
at 7:44pm 01.05.16
0/673
Our almost 70 day journey began on June 15, 2015 at Shelter Bay Marina, across from LaConner in what
|
Inverter Bilge query
Jeff2650 at 10:03am 03.09.23 All, thanks for your responses, good advice on many levels. I wasn't clear in my original post. The |
||
TOO MUCH WIND?
Kings Gambit at 9:35am 03.09.23 Yes. I know line squalls of the Chesapeake are notorious. As is similar in SW FL. Humidity-driven st |
||
TOO MUCH WIND?
mermike at 9:26am 03.09.23 I took a date out sailing (long ago) and pitchpoled a Prindle 16 at speed. I always wondered what is |
||
TOO MUCH WIND?
dlochner at 8:23am 03.09.23 As one ages, one's thoughts about reefing change. I was once in the never reef and fly the 150 all t |
||
1984 Hunter 31 - Cast Iron Keel Rust
anelso29 at 8:09am 03.09.23 Interlux 2000 is a two part epoxy. Main thing is grind/sand to bare shiny metal and apply 2000 imm |
||
Spinnaker in top pulley-is it a concern? (1)
kloudie1 at 8:07am 03.09.23 here is what the spin halyard on a crane looks like: e halyards and forestay. Some fractiionally rig |
||
A story of the engine that could.... Then didn't
dLj at 8:00am 03.09.23 I had a good day. Got the cutlass bearing and new shaft installed. Then we put on the PSS Dripless |
||
O' Day 40, and or choice and selection?
steve_d at 7:46am 03.09.23 (85) Anchoring, how to stop dragging and be secure. - YouTube I thought this was an interesting vi |
||
TOO MUCH WIND?
Kings Gambit at 7:45am 03.09.23 My two most common instances would be reefing when Santa Ana winds are about in case a big gust or w |
||
Spinnaker in top pulley-is it a concern?
Sailfanatic at 7:44am 03.09.23 Thanks for the responses, Annapolis installed the spar and halyards, and designated one as a spinna |
||
TOO MUCH WIND?
Kings Gambit at 7:20am 03.09.23 That looks like it might have been fun 60 years ago but now I reef early and stay comfortable! I s |
||
Proper prop size tartan 33
Dave Groshong at 7:09am 03.09.23 Most prop shops will ask the waterline length, max RPM's, max speed, transmission reduction ratio |
||
Spinnaker in top pulley-is it a concern?
Jeff2650 at 6:57am 03.09.23 Thanks for the responses, Annapolis installed the spar and halyards, and designated one as a spinnak |
||
Search issue
HomeyD at 6:53am 03.09.23 Browser set-up was overshadowing top of page. Shut down and reloaded. Good now. |
||
Hunter 410 curved companionway step
kloudie1 at 5:33am 03.09.23 Take the step to a local cabinet or woodworking shop to get an estimate? |