Davey J
at 10:34am 08.18.23
6/899
I currently have an Olson 25 in the SF Bay area, and want to get a trailer for it. I've seen a coupl
|
||
Fly4rfun
at 6:45pm 08.17.23
2/1150
on the mod page is a DIY furler done by CA guy, photos only, does anyone have info on how to constru
|
||
mikeracca
at 4:22pm 08.17.23
68/9288
Hey there everyone. Well I did it again. I bought an abandoned Catalina that needs lots of love. Thi
|
||
flightlead404
at 11:46am 08.17.23
42/3977
I'm in the process of expanding my 6 month old 400AHr LiFePO4 house bank to 600AHr by adding an addi
|
||
Inactive Member 157604
at 9:30am 08.17.23
5/927
Does anyone have any experience installing a whisker pole / track on a furling system mast? Worried
|
||
Invest 99L (1)
JamesG161
at 7:40am 08.17.23
2/499
The African Monsoon Season is underway.
|
||
Adamsson
at 6:34am 08.17.23
24/1488
We've had solar panels on our boat since we purchased it, but I'm only now looking at them more clos
|
||
MikeHoncho
at 7:31pm 08.16.23
12/1441
System is less than a year old and has worked flawlessly until this trip. Used precisely a month ago
|
||
drharney
at 5:23pm 08.16.23
2/1382
Man, its difficult to find a bimini and get the placement right on this boat. The backstays, or the
|
||
Nate
at 2:38pm 08.16.23
12/1413
|
||
Spar Trek
at 2:32pm 08.16.23
11/2180
|
||
geoffschultz
at 12:29pm 08.16.23
2/246
I'm in the process of designing a 55' catamaran. My wife would love a washer and a dryer, and I'm t
|
||
elvio
at 11:42am 08.16.23
9/1487
218866 My Sparcraft Vang (?37560020505?) is broken. I think it's time for a new one. Can someone re
|
||
gfcng
at 11:26am 08.16.23
15/1909
Hello, I recently purchased an 89 standard rig Cat 30. The main is led aft to a cabin top winch. I'v
|
||
DinghySailor
at 10:55am 08.16.23
4/1313
218859218859
|
||
Broken Rudder (2)
jdearl
at 10:54am 08.16.23
14/2158
I have a Hunter 170, believe it is a 1999 or 2000. Out sailing the other day and the rudder blade br
|
||
DinghySailor
at 10:42am 08.16.23
6/1332
A plumbing question. Our freshwater galley foot pump (Whale Gusher Galley III) has over the past yea
|
||
Tide Clock (1)
jviss
at 10:06am 08.16.23
44/2705
I always wanted one of these. Now that I love so close to the shore, and to my boat, I considered i
|
||
JamesG161
at 8:36am 08.16.23
14/1737
This Hurricane Season 2023 has been very active so far. Note the name Hilary or #8 on that Area Nam
|
||
PhilaSailor
at 7:25am 08.16.23
18/1400
Hello, I've just completed a refit of an '83 Cutter 37. There was endless research and trials to f
|
interior boom assemblies?
shemandr at 2:09pm 02.17.25 I think having a functional outhaul is a great upgrade. As we know it controls the depth of the who |
||
Self-Bailer on Trinka 8' Dinghy
Skipper J at 1:00pm 02.17.25 Hi All, I appreciate the feedback. It sounds like I'd be better off leaving it as it is, with the dr |
||
Steps to open and check copper tubes on heat exchanger for Universal M25-XPB engine?
BigEasy at 12:43pm 02.17.25 I used a brass gun cleaning brush and rod (22 caliber diameter) to thoroughly clean the tubes. The |
||
Flanged seacocks installation with Beneteau grid liner?
dlochner at 12:40pm 02.17.25 I used a hole saw of the correct diameter, but without the pilot bit. It was hard to get the hole s |
||
Re-routing Mainsheet H27
David in Sandusky at 11:50am 02.17.25 I would suggest end of boom sheeting if this is at all ,possible. Our '77 h27 is sheeted from the en |
||
Re-routing Mainsheet H27
jssailem at 11:38am 02.17.25 I grew up sailing dinghies and small boats. I understand your experience of having the main sheet in |
||
Hunter 33 water leak at compression post (2)
KyleH at 11:15am 02.17.25 Thanks for the reply's. I did investigate the wire box, and it didn't appear to be the source, I'll |
||
Hunter 170 crack down to keel
DFD at 10:59am 02.17.25 You definitely have high stresses occurring under the cracks. This will require building up the hu |
||
Older CDI furler
Timm R Oday25 at 10:54am 02.17.25 Hopefully this will help . The shackle you show might as well be used securing the foot of the sail |
||
Flanged seacocks installation with Beneteau grid liner?
Ralph Johnstone at 10:50am 02.17.25 I could provide links to the owner's groups, forums where this has been discussed, etc, but this is |
||
Hunter 40.5 Stbd water tank leak
Rich Stidger at 9:51am 02.17.25 Try resealing the screws first before escalating the job. Access to the portside tank is hard becaus |
||
Steps to open and check copper tubes on heat exchanger for Universal M25-XPB engine?
JoeWhite at 9:19am 02.17.25 On my M35B Universal, the antifreeze drain is a plug on the engine block on the port side. Look on y |
||
Flanged seacocks installation with Beneteau grid liner?
jbmia at 9:17am 02.17.25 Hmmm. My last bullet point was this: "- None of this is helping the OP decide whether he can enlar |
||
Hunter 40.5 Stbd water tank leak
danielsan at 8:44am 02.17.25 Maybe you don't need to remove the lid. I had leaks on my port tank and I simply removed all of th |
||
Re-routing Mainsheet H27 (1)
DHembree at 8:35am 02.17.25 There is no traveler car, but a bridle that straddles the companionway with the cleat shown. Now, I |
||
Flanged seacocks installation with Beneteau grid liner?
dLj at 8:22am 02.17.25 - Another guy is reasonable and wants to understand the root problem, but seems to be holding me p |