|
Dijobi777
at 8:23am 08.23.16
5/1604
DIY or recommend a vendor Thanks
|
||
|
HillbillyWanderer
at 7:04am 08.23.16
4/3901
Hoping to finally get back to working on my boat again. Have had other projects that have been takin
|
||
|
GGordonWoody
at 6:48am 08.23.16
8/5169
Maneuvering our 8+ ft wide ship into our 10- ft slip means working the shifter quite a bit during do
|
||
|
Dennis Kitchen
at 6:38am 08.23.16
8/1399
I have progressed in my H25 rebuild to the point of setting the main bulkhead and mast compression p
|
||
|
Bob S
at 5:26am 08.23.16
55/13906
I have a question for the group. My wife, the admiral, has been having a rough time this season with
|
||
|
Kermit
at 4:44am 08.23.16
13/2411
Peggie Hall has been extolling the virtues of PureAyre for a while now. I *finally* ordered a gallon
|
||
|
hook
at 3:13am 08.23.16
3/803
I think I need to replace my running rigging. It still gets the job done, but is starting to get tha
|
||
|
Ken13559
at 12:43am 08.23.16
14/3635
I wish to run emery cloth/sandpaper on the V pulley slot face to remove any fine pitting that is cre
|
||
|
gfrazzle
at 10:09pm 08.22.16
1/426
Hello all, The batteries on this PLB are out of date. This model is no longer available but there ar
|
||
|
Dalliance
at 8:49pm 08.22.16
18/920
I just wanted to share some weather photos I shot last week. They were taken over a 29 minute per
|
||
|
MikePoplin
at 6:45pm 08.22.16
4/1471
I'm looking for the bracket that attaches to the bottom of the galley table. It's a Recmar system;
|
||
|
Full Circle 473
at 5:19pm 08.22.16
10/2124
My UV cover on my Genoa needs to be reattached. About 18" is coming off 1/3 down from the head. Can
|
||
|
Randall Schmidt
at 4:58pm 08.22.16
3/607
I'm looking at a long ICW journey on my 1984 ODay 28 that I just bought. I'm seeking tips on how ot
|
||
|
Randall Schmidt
at 4:55pm 08.22.16
40/6403
I have an ODay 28 and am planning a retirement trip down the ICW from Annapolis to Mobile Bay Alabam
|
||
|
Ron20324
at 3:47pm 08.22.16
6/620
On QVC Shopping today, and for a limited time only- I hope... Item A-286300... "ELEMIS Pro-collagen
|
||
|
Donald6433
at 3:09pm 08.22.16
0/431
Has anyone installed an anchor windless on a Vision 36? If so what brand did you install and how di
|
||
|
fred1diver
at 2:09pm 08.22.16
20/2430
I'm glad I bought a second battery before my trip, my battery didn't last 2 days, and that was with
|
||
|
AXEL
at 1:57pm 08.22.16
8/1101
I recently bought this C30 MKIII. During the survey it was pointed out that the volt meter was bad,
|
||
|
Wind Cree
at 12:56pm 08.22.16
3/1628
I recently purchased a Pearson 28 from 1975. The hand pumps in the galley and head are not operatin
|
||
|
zigracer
at 11:29am 08.22.16
1/593
x
|
|
Simple electronic install - first time advice needed
mermike at 6:53am 04.06.24 Just don't ask which anchor is best...:biggrin: |
||
|
RECOMMISSIONING THE FRESH WATER SYSTEM
RoyS at 6:31am 04.06.24 Water heater will drain quickly if you hold open the pressure/temperature relief valve lever while t |
||
|
Simple electronic install - first time advice needed
circa1971la at 5:57am 04.06.24 Thank you all so many wonderful suggestions. It seems of all of these, the best option is to use the |
||
|
Simple electronic install - first time advice needed
elink at 5:40am 04.06.24 While the discussion continues on this, circa1971la, you can likely make a decision on what is best |
||
|
170 cracked warranty hull
Crazy Dave Condon at 4:59am 04.06.24 The very first thing you need to do is drill a 1/8 inch hole at the end of each crack about a quarte |
||
|
Hunter 34 rudder
JamesG161 at 12:18am 04.06.24 You can find the owners manual and more on Hunter 34. Hunter resources, by model Jim... |
||
|
3GM30F Service Issue
jssailem at 12:04am 04.06.24 You say rough starting in cold weather, Do you have glow plugs? When you look at the exhaust is ther |
||
|
Hunter 34 rudder (1)
Marauder at 11:28pm 04.05.24 Thanks guys for the replies and info, much appreciated. The HIN says its an 1985. Claude your rudder |
||
|
Rebuild of high pressure fuel pump for Yanmar 3GM30F
skunther at 10:49pm 04.05.24 Please see my thread on 3GM30F. I could really use some help on this one. After they worked on the i |
||
|
3GM30F Service Issue
skunther at 10:40pm 04.05.24 On Thursday the shop sent another tech to check out the engine. First crank of 10 seconds produced n |
||
|
Does anybody know what size wire or threaded rod life lines are on Catalina 320, 2004
Ted10028 at 9:20pm 04.05.24 I simply added a pelican hook to the end toggle and there was enough room in the turnbuckles to tak |
||
|
Does anybody know what size wire or threaded rod life lines are on Catalina 320, 2004
Ted10028 at 9:19pm 04.05.24 Wire is 3/16 coated to 5/16, threaded studs are 5/16-24. The pelican hook is shorter than the lifel |
||
|
Simple electronic install - first time advice needed
dLj at 8:57pm 04.05.24 There's a reason boat builders and Nasa don't solder any wire joints... although not sealed, mechan |
||
|
Simple electronic install - first time advice needed
marcham at 7:59pm 04.05.24 There's a reason boat builders and Nasa don't solder any wire joints... although not sealed, mechani |
||
|
Simple electronic install - first time advice needed
dLj at 7:14pm 04.05.24 I inadvertantly edited out part of my post. I was going to suggest that he strip the wires twice th |