|
Capt.JDavis
at 1:13am 11.06.16
0/640
What is a good, reliable source for purchasing a rebuilt M25 at a reasonable price in the market the
|
||
|
Greg Wozniak
at 9:11pm 11.05.16
25/2614
Our original jib has to be replaced (thank you Hurricane Matthew). We are looking to add a 135. Othe
|
||
|
PacificSailor
at 9:09pm 11.05.16
8/2575
Looking at a 2004 Hunter 216. I haven't seen it yet, but the owner says that the "floor under the se
|
||
|
Whitsonenator
at 7:43pm 11.05.16
6/515
I just bought a Hunter 18.5 and I need to buy an outboard motor. What size motor is recommended fo
|
||
|
gkmoore
at 7:36pm 11.05.16
10/2675
I'm sanding down the tiller as the previous finish had some cracks/peeling going on. Where the finis
|
||
|
dennisv
at 6:04pm 11.05.16
4/931
The aluminum hinges (2) on the frame of my forward hatch have broken. Has anyone had to replace the
|
||
|
newsailor72
at 3:41pm 11.05.16
12/3243
looking at a catalina 22, took some pic's. does the keel look serviceable to you? how much do you
|
||
|
NYSail
at 2:36pm 11.05.16
27/5712
so..... think we have found a boat. All the right stuff and reasonably good condition (prior to surv
|
||
|
brad minda
at 10:34am 11.05.16
6/1642
Discovered that my bilge pump is not working. my boat is an 85, I can't seem to locate a fuse, the f
|
||
|
freeheelbillie
at 6:36am 11.05.16
9/1196
1992 MKII 30', tall rig with a Mack Pack and lazy jacks. Mainly a cruiser with occasional beer can
|
||
|
TWM
at 1:22am 11.05.16
6/2169
We have recently bought our c309 TWM based on Pittwater in Sydney. Fuel capacity at 100+ litres is g
|
||
|
seattle-hunter-31
at 7:50pm 11.04.16
23/6621
I had my bottom repainted ($1300, plus $500 haul out), and after 1 month it's peeling off in a numbe
|
||
|
seattle-hunter-31
at 6:42pm 11.04.16
33/10206
I have finished an investigation of the deck and found the following: 1. The single drainage path i
|
||
|
Zach Grammon
at 6:22pm 11.04.16
14/6892
Recently I gave an old car to a friend of my brother. The young guy is a stainless steel welder, an
|
||
|
Ilanortho
at 5:55pm 11.04.16
7/535
Sent my main sail to Sail Care and as I suspected it is beyond reconditioning. They are proposing to
|
||
|
sdstef
at 2:14pm 11.04.16
15/1598
I had a nasty surprise when I returned to my boat after a few days. I left the head (jabsco} pump t
|
||
|
Keith13315
at 2:11pm 11.04.16
5/868
Hi I am looking at a 1998 H340. It has a water leak on the starboard side in the V Berth and also th
|
||
|
dehler25
at 1:25pm 11.04.16
12/3060
Anyone come across Polar specs on Hunters? I have noticed that there are weather routings that can a
|
||
|
Warren Milberg
at 12:20pm 11.04.16
42/5930
I was at the boat show this year. I was amazed to see that it was hard to find a boat that was less
|
||
|
dries77
at 12:13pm 11.04.16
8/1404
Hi all, I there anybody on this forum with a 33 who has a bowthruster installed? Would like to have
|
|
Sarasota Bay Returning (2)
rgranger at 8:19pm 04.26.24 Before you lay down the tile, I would recommend these two products get rid of the mold and mildew w |
||
|
NYC to Chicago on a sailboat (mast removed of course)
dlochner at 7:17pm 04.26.24 Time constraints are the biggest issue. The fastest route is to take the Erie Canal from the Hudson |
||
|
NYC to Chicago on a sailboat (mast removed of course)
dlochner at 7:04pm 04.26.24 I'd consider draft as the limiting factor. If water is too skinny in the canal for your boat, then |
||
|
NYC to Chicago on a sailboat (mast removed of course)
Scott T-Bird at 6:58pm 04.26.24 I'd consider draft as the limiting factor. If water is too skinny in the canal for your boat, then |
||
|
The Great Lakes....
Scott T-Bird at 6:34pm 04.26.24 Due to the counterclockwise current and prevailing westerlies throughout the summer, the Michigan sh |
||
|
The Great Lakes.... (1)
dlochner at 6:25pm 04.26.24 The deepest parts of Lakes Superior, Michigan and Ontario are hundreds of feet below sea level. |
||
|
NYC to Chicago on a sailboat (mast removed of course)
Project_Mayhem at 6:04pm 04.26.24 Have you looked into the Great Loop Association? |
||
|
The Great Lakes....
quadrille38 at 5:28pm 04.26.24 The Great Lakes contain 1/5 (20%) of all the fresh surface water in the world. |
||
|
MPPTs / inverter / battery compartment ventilation
JoeWhite at 4:28pm 04.26.24 I use 3 1/2" computer fans. They draw about 34mA each. You can use 2 to bring air in and 2 to take a |
||
|
Metal lathe
garymalmgren at 3:48pm 04.26.24 Steve of Acorn to Arabella fits a Balmar alternator. He sent off his measurements. received his new |
||
|
MPPTs / inverter / battery compartment ventilation
dlochner at 3:02pm 04.26.24 Are you concerned about heat or about off gassing from the batteries? |
||
|
NYC to Chicago on a sailboat (mast removed of course)
dlochner at 2:56pm 04.26.24 The route is pretty straight forward once you get to the Lake Erie. To get to Lake Erie there are |
||
|
West Marine CPP Ablative Antifouling Paint - Opinions?
Ralph Johnstone at 2:38pm 04.26.24 Epoxy barrier with a different colour is good as well. What type of antifouling paint do you use and |
||
|
https://youtu.be/qaYsRSZ3CSQ?si=-tE9G7JwoqpNMIfZ (1)
rardiH36 at 2:06pm 04.26.24 1) Taking notice of this thread, I thought to link you to my posts about my strut replacement eight |
||
|
Sarasota Bay Returning
patrickfarley at 1:14pm 04.26.24 Carpet tile sounds interesting. Everything is a redo on the boat. I redid the seats and now they |