natep
at 5:24pm 06.19.23
4/518
My tachometer is acting up. When we start the engine the tachometer works for about 10 minutes and t
|
||
aas1110
at 3:10pm 06.19.23
2/279
Hello all - Hoping to get some advice/direction/instructions on replacing headliner on the V-berth
|
||
mhessick
at 3:01pm 06.19.23
41/2571
I was given a 1989 22 Catalina with an outboard motor. I would like to make sure that it runs. Is
|
||
JamesG161
at 1:39pm 06.19.23
7/827
The Storm watch is out. ing models ECMWF and GFS are still different. It is that time of the season
|
||
B-ness
at 1:31pm 06.19.23
7/569
Does someone know the lengths of the battens in the mainsail of the H26? Also, any advice regarding
|
||
mhessick
at 11:01am 06.19.23
4/554
I recently acquired a 1989 Catalina 22 with a CDI Roller Furling system. Can anyone tell me what ha
|
||
mbaker267
at 10:07am 06.19.23
14/974
I recently received a 1976 Cat-22 so have no experience with it. I am in the process of refurbishing
|
||
jmackdaddy
at 9:13am 06.19.23
20/1075
I need some help trying to determine what boat(s) I should be looking for based on my needs. I recen
|
||
inkunzi
at 8:07am 06.19.23
5/825
I have not yet launched this 1991 Hunter 27-2. Engine is 1GM10 I just replaced all 4 engine mount
|
||
Mice vs. Sail (1)
meross
at 7:25am 06.19.23
9/546
216984216984
|
||
soopad00pa
at 7:37pm 06.18.23
14/769
Hi, I was sent here from cruisersforum for o'day specific info and it seems like you guys do have a
|
||
ricksoth
at 6:54pm 06.18.23
27/1347
I need guidance on my fresh water system. The PO had a 3" x 15" PVC 'tank' plumbed into the syste
|
||
albakers
at 6:53pm 06.18.23
2/488
|
||
spadaforaj
at 5:54pm 06.18.23
18/844
New Kuma water heater worked great for a season - and now won't heat through the heat exchanger Re
|
||
mwill
at 2:35pm 06.18.23
7/978
We purchased a 1985 catalina 36 mkI last year and are uncertain about the state of the keel bolts. T
|
||
thetone
at 12:46pm 06.18.23
1/336
I recently removed the rudder on my 1990 Beneteau 35s5. It was not easy, I had to cut one of the ste
|
||
HugoJaramillo
at 11:41am 06.18.23
0/247
Looking for recommendations on where to pick up used or new Bimini, dodger ' dinghy davit. 1999 Hunt
|
||
Bscott515
at 8:11am 06.18.23
8/613
Anyone know the location of the ELCI on a 2003 Beneteau 393?
|
||
Unremarcable
at 7:50am 06.18.23
5/954
Does anyone happen to have a diagram of or knowledge of the swing keel routing for an O'Day 222? I h
|
||
john6206
at 6:02am 06.18.23
19/1275
This might sound like a stupid question, especially from someone who has been trailer sailing for so
|
Caulk/sealant for shower enclosure with teak trim
skunther at 7:23am 06.09.24 Use a good quality bath and tub caulk. Meets all the necessary criteria and is not exposed to UV, s |
||
Caulk/sealant for shower enclosure with teak trim
dlochner at 6:58am 06.09.24 Use a good quality bath and tub caulk. Meets all the necessary criteria and is not exposed to UV, so |
||
Portlight Polish
skunther at 6:57am 06.09.24 When I sold the boat four years later, the ports were still clear. I did not use any UV protective |
||
Propeller shaft length Hunter 376, 380 or 386
Hamish_s at 6:09am 06.09.24 Just did this on a Mirage 35. We had specs which were close, but the shaft ended up having to go ba |
||
Merit 22 owners
jefstr at 8:59pm 06.08.24 I'm new to sailing and hoping to get my Merit 22 in the water this W, Th or F. What would be the min |
||
Shaft coupling flange
igillerman at 8:29pm 06.08.24 Closing the loop here. Unclear if I have the wrong coupler, the shop who sold me the shaft and sold |
||
3GM30F Service Issue
skunther at 8:19pm 06.08.24 The engine cranked over stronger and started up within 10 seconds. Not as good as it was before, but |
||
Portlight Polish
rgranger at 6:52pm 06.08.24 When I sold the boat four years later, the ports were still clear. I did not use any UV protective s |
||
Portlight Polish
rgranger at 6:50pm 06.08.24 Very nice results. Did you machine polish with foam or wool or did you hand polish? I need to wor |
||
Knocking sound at 2000 rpm's
Prozac at 1:24pm 06.08.24 As in life, so it is with diesels ............... DO NOT go for the most complex and expensive so |
||
Knocking sound at 2000 rpm's (1)
Ralph Johnstone at 1:12pm 06.08.24 I am guessing a bent prop shaft or struts? Any advice would be appreciated. As in life, so it is |
||
Best way to transport first boat? Advice Requested
Barnacle Bill at 12:59pm 06.08.24 First of all, as seen in the photos, the trailer has surge brakes. Whether they work or not, is anot |
||
Moving the traveller questions
dlochner at 12:57pm 06.08.24 Well, if you have lots of money to burn on a new traveller system and lots of line and a new boom to |
||
Moving the traveller questions
Barnacle Bill at 12:30pm 06.08.24 There are a few things to think about. First of all, when you move the mainsheet attachment to a mid |
||
Shaft coupling flange
Barnacle Bill at 12:22pm 06.08.24 My guess is you don't have the right coupler. |
||
Knocking sound at 2000 rpm's
jssailem at 7:43am 06.08.24 If this were a crime, the detectives would go to the streets and round up the "Usual Suspects". :big |
||
Propeller shaft length Hunter 376, 380 or 386
JamesG161 at 7:16am 06.08.24 You should never replace your shaft while in the water. Jim... |