uncledom
at 3:59am 07.19.18
8/1056
I thought my Wema tank sensor was failing but it turns out the Sea Tech shut off valves are leaking
|
||
rfrye1
at 10:15pm 07.18.18
3/560
My 1998 H376 wood floor is showing some wear and tear. I'm considering refinishing it. I assume the
|
||
Mcewan007
at 8:16pm 07.18.18
16/7306
|
||
Rltgold
at 7:25pm 07.18.18
19/1373
What is the largest motor you can use on a Catalina 22 ? Thanks
|
||
AlastairLC
at 7:13pm 07.18.18
64/12919
Having just had Bella Zee's hull recoated, I noticed that the finish was rough, gritty really. Denni
|
||
Rob2435
at 6:30pm 07.18.18
4/618
Got a new to me chartplotter but need the power cable, any lead on one would be great.
|
||
Brian D
at 5:45pm 07.18.18
1/540
XDbPa9ENM6I
|
||
Sanfelice
at 5:26pm 07.18.18
26/4160
I have a dry bilge except when running the air conditioner. The drip tube in the bilge runs perpendi
|
||
Rick D
at 3:49pm 07.18.18
9/805
I have 400 watts solar from four 50's and two 100's. The two 100 s are new. All are ganged into the
|
||
mholzmann
at 2:09pm 07.18.18
0/539
Prior to 1995 many of the Catalina Sailboats 27' to 42' had a very same Companionway Hatch. Very co
|
||
Rick Macdonald
at 1:54pm 07.18.18
8/1100
153868 The photo shows the broken spacer. I have none at all now and the main halyard binds between
|
||
Dave Pawloski
at 12:58pm 07.18.18
1/498
My 1985 Hunter 31 is equipped with a Streamstay II jib furler (from when I purchased the boat in 19
|
||
capta
at 11:08am 07.18.18
8/608
This boat came with an Alden Marinefax TR-VI, but no paper. I thought it might be good to get it goi
|
||
MacR2Wim
at 10:25am 07.18.18
5/7710
I own and sail a 1984 Catalina 30 in a large freshwater lake in MS. Because there are no facilities
|
||
Mity
at 9:35am 07.18.18
10/13959
Hi I just bought a Garmin Echomap Plus 65cv and I would like to connect it to the Raymarine equipme
|
||
Maine Sail
at 4:57am 07.18.18
25/15673
I get asked this electronics question more than just about any other from customers who have a perfe
|
||
KennyBene
at 4:11am 07.18.18
50/3319
1999 B352 with C80 MFD, ST 50 plus autopilot and compass None of these instruments show the same he
|
||
Matt weimer
at 3:45am 07.18.18
27/6724
|
||
Mighty Little
at 9:03pm 07.17.18
2/1497
|
||
learningasigo
at 6:05pm 07.17.18
3/448
Anyone know whether the 5/16 anchor rode chain is G30 or G40?
|
Stripped screws in plastic
rgranger at 8:52pm 07.02.24 What about wrapping screws in teflon tape? :plus: Or Saran wrap |
||
Question on Changing Keel Wench in the Water
Davidasailor26 at 7:42pm 07.02.24 That's another thought I've been having. I'm worried that if there isn't enough cable and I let it |
||
Bilge Keel on a hunter 22
Davidasailor26 at 7:11pm 07.02.24 Sounds ambitious. I think it would take a lot of work to reinforce both sides of the hull to handle |
||
Question on Changing Keel Wench in the Water
jmobx at 7:04pm 07.02.24 I vote to remove from the water on the trailer. You do not have to lower the mast to work on the ke |
||
Best non toxic anti-fouling for PNW?
Don S/V ILLusion at 6:06pm 07.02.24 . If it was just organic copper that was steadily washing off i wouldnt be too concerned but the da |
||
Bilge Keel on a hunter 22 (1)
jssailem at 5:58pm 07.02.24 A bilge keel boat. t seen a Hunter 22 with this configuration. At least not a factory item. I guess |
||
2005 Hunter 31 or 1992 Hunter 37.5 Legend?
jssailem at 5:53pm 07.02.24 - A good rule of thumb is that operation and maintenance costs go up with the square of the length. |
||
Best non toxic anti-fouling for PNW?
jssailem at 5:42pm 07.02.24 Would i be correct in guessing the non toxic ones are best suited to small boats or ones that are r |
||
Best non toxic anti-fouling for PNW?
Davidasailor26 at 5:38pm 07.02.24 data sheets for all the paints ive looked at are pretty clear they are harmful to life By definiti |
||
Question on Changing Keel Wench in the Water
JoeWhite at 5:24pm 07.02.24 I vote to remove from the water on the trailer. You do not have to lower the mast to work on the kee |
||
Best non toxic anti-fouling for PNW?
adamv at 4:14pm 07.02.24 On my last paint job, I sanded down the full previous coat and most of the one before that. I used |
||
Better use of cabinets
Hayden Watson at 2:53pm 07.02.24 I would build a shelf at mid height or a bit higher. I would then remove the bar and install a thin |
||
Stripped screws in plastic
thinwater at 2:52pm 07.02.24 No... when I first read i thought I read "drill the holes" larger in the sender for a bigger screw |
||
Stripped screws in plastic
Rich Stidger at 2:44pm 07.02.24 Hi Greg. Try this repair using super glue and baking soda to fix your plastic hole. Scroll through |
||
Best non toxic anti-fouling for PNW?
Hayden Watson at 2:43pm 07.02.24 On my last paint job, I sanded down the full previous coat and most of the one before that. I used |