Chuck C.
at 7:12am 07.27.18
6/650
Just wondering what is the trick to using those three friction locks built into the front of the boo
|
||
Leeward Rail
at 7:02am 07.27.18
7/1693
Hello all, A new sailor at our marina has a Bayfield 25 He is replacing the shaft (broken at the for
|
||
David11038
at 6:50am 07.27.18
4/546
On my Oday 322, I found fuel leaking into the bilge, it appears to be the fuel lift pump gasket wher
|
||
Fred
at 6:40am 07.27.18
16/1311
weve been anchored out a few nights now and if the water is not completely still the centreboard ten
|
||
Caspurr
at 5:46am 07.27.18
14/1365
Last night my head sail roller furler jammed a couple of times and sail only rolled out partially.
|
||
danstanford
at 5:31am 07.27.18
11/671
This has happened to me twice now and I would like to develop a solid strategy to avoid the crisis.
|
||
Maine Sail
at 5:29am 07.27.18
41/3015
I feel sorry for folks cruising Maine over the last two weeks. The fog has been pretty relentless an
|
||
Skipper
at 6:27pm 07.26.18
14/1364
Or should I run a chute too?
|
||
Brian D
at 4:21pm 07.26.18
3/5744
Hope this works... if not, sorry... I don't think you need a facebook account to view this. When the
|
||
Blackacre
at 3:56pm 07.26.18
44/4666
Still looking to buy a cruising sailboat. For 2/3 years now we have been talking about buying/outfi
|
||
parasloth
at 1:06pm 07.26.18
0/355
Looking for used sails for a sewing/decorating project. If you have any lying around, instead of to
|
||
PropellerHead
at 10:13am 07.26.18
2/837
I pulled the trigger on a CDI FF2 furler. I gather from the manual and searching on this forum that
|
||
pateco
at 8:28am 07.26.18
56/6052
OK, so the Stargazer still has her original Barlow 2 speed winches from 1983. I have been saving up
|
||
Maurice Doran
at 8:12am 07.26.18
13/1261
Hi everyone, Hope you're all enjoying the summer weather. I have a refrigeration question for Hunt
|
||
davehursh
at 8:02am 07.26.18
1/786
My latest boat (and possibly my last at age 79) is a Morgan 22. I need information about the center
|
||
Jeff Gray
at 7:30am 07.26.18
13/1689
Hi All, I had an odd experience with anti-fouling bottom paint that might be worth knowing about.
|
||
Jerry Clark H356 SV Persi
at 7:15pm 07.25.18
5/556
There is a fellow sailor over on CruisersForum.com where I also spend some time. He has a 2006 Hunt
|
||
Willemvan
at 5:58pm 07.25.18
4/518
why does my h26 seem to sail better on the port tack?? The main sails tell tails seem to stream out
|
||
Oduy
at 5:48pm 07.25.18
2/712
Hello all, I recently purchased an O'Day 25. The spreader base which is attached to the mast has sn
|
||
Ed 87Cat
at 5:16pm 07.25.18
1/406
I am looking for a new boat after selling my C30 this season. I have always had a fondness for the
|
Old DataMarine instrument ...does it speak NMEA0183?
Tally Ho at 5:06pm 08.02.23 Updating my post on an Arduino adapter for this. The 0.1 mile pulse is going to result in a very s |
||
Pearson Ensign a good first boat (given context in the post)?
jon hansen at 4:37pm 08.02.23 the ensign is the prettiest girl at the dance. best dancer too. now what are you going to pick? m |
||
Alder Barbour Refrigeration
Hayden Watson at 4:16pm 08.02.23 attached is the document for a similar controller from Danfoss where is discusses the resistor for |
||
Alder Barbour Refrigeration
jviss at 3:56pm 08.02.23 The best system is one that runs as slow as possible while still maintaining the desired temperatur |
||
Bomar hatch dog
jviss at 3:51pm 08.02.23 The latch dog snapped at the red line. There is a roll pin that goes through the hole (green arrow |
||
Bomar hatch dog
jviss at 3:50pm 08.02.23 FYI- the lazy jib sheet lodged under the hatch and the jib filled with air before I could tighten t |
||
Bomar hatch dog
BTC1984 at 3:46pm 08.02.23 FYI- the lazy jib sheet lodged under the hatch and the jib filled with air before I could tighten th |
||
Bomar hatch dog (1)
BTC1984 at 3:41pm 08.02.23 The latch dog snapped at the red line. There is a roll pin that goes through the hole (green arrow) |
||
VHF Handheld
jviss at 3:40pm 08.02.23 I had a cheap Uniden (Atlantis 250) Handheld for years (maybe ten). It worked well enough but the r |
||
Ruddercraft Lower Pintle Failure
kloudie1 at 3:28pm 08.02.23 Probably comes from some metallurgical distress that the weld causes.. Gene's fix with no welds and |
||
Bomar hatch dog
kappykaplan at 3:14pm 08.02.23 Please provide photos of the sides of the broken dog. |
||
Applying Cetol question
jviss at 3:02pm 08.02.23 Ya know, I had a terrible time with my Pearson 39 toe rails. They were solid teak and water had int |
||
Applying Cetol question
jviss at 2:58pm 08.02.23 I used Cetol on my boats. If you want Cetol to look like varnish, sand, prep and apply the same |
||
Applying Cetol question
dmax at 2:38pm 08.02.23 I replaced my toerails with synthetic teak - too many linear feet of edging to finish (104'). The re |
||
Pearson Ensign a good first boat (given context in the post)? (2)
jssailem at 2:36pm 08.02.23 You need to look at the design to understand the designers intended use of the boat. 1. Pearson-En |
||
Applying Cetol question
Rick486 at 2:32pm 08.02.23 I have given up on the idea or a real varnish finish on my toerails. Wondering, has anyone applied |
||