SWagner
at 11:23am 09.24.18
11/1094
I have a 2005 Hunter 38 with a 40 hp Yanmar. She runs beautifully, well until recently. I was cruisi
|
||
Raider_Bob
at 11:01am 09.24.18
5/385
I have a new to me sailboat that my surveyor stated the wiring both DC and AC are a mess, but a 30 y
|
||
SWagner
at 10:59am 09.24.18
0/16
I have a 2005 Hunter 38 with a 40 hp Yanmar. She runs beautifully, well until recently. I was cruisi
|
||
Mike P16616
at 10:28am 09.24.18
1/410
My hunter 23.5 suffered some damage to the windshield and side windows. I can order a windshield fro
|
||
Hayden Watson
at 10:19am 09.24.18
11/845
After nursing it along for 20 years, my obsolete Arctic furnace gave up the battle this past week so
|
||
plenny7
at 10:19am 09.24.18
30/2402
We had a seaplane land on our lake yesterday while we were sailing. At first I thought it was makin
|
||
mciron9
at 8:44am 09.24.18
35/1834
My last boat was a wood hull 34' Trojan, which was very costly to maintain and cruise. So, thinking
|
||
Jackdaw
at 8:41am 09.24.18
12/911
Last weekend, windward mark in 18 knots gusting to 25. A poorly timed gust and shift overloaded us d
|
||
Rick
at 8:33am 09.24.18
6/524
After a week in Catalina, my 420 Passage has developed a fresh water leak. I am going to have to in
|
||
Spellman66
at 7:56am 09.24.18
15/1938
I have a refrigerator that doesn't drain on my 2004 310. At first I looked for a Y valve and there
|
||
Todd Atchison
at 7:44am 09.24.18
3/496
So after a few shakedown cruises we are prepairing S/V Sea Gypsy for four days and five nights on th
|
||
Ken Cross
at 6:17am 09.24.18
31/2125
Hi all. I get to miss lots of sailing. I broke my shaft strut and haven't been able to fix it yet. t
|
||
Rob Heath
at 1:54am 09.24.18
2/2597
Hi I am looking for a manual for my Dolphin Charger 12V 25A fitted to my 2009 Oceanis 37. Would anyo
|
||
Shorefun
at 6:43pm 09.23.18
1/375
How solid should the floor feel from the swing keel aft towards the transom? There is some movement.
|
||
Shorefun
at 6:40pm 09.23.18
1/414
Well I had a crack that went under the anti skid on the port side. It was easy to get a fingernail u
|
||
Shorefun
at 6:35pm 09.23.18
3/522
Just looking at my 170 and the chain plates caught my eye. They do not need to come out and I am no
|
||
Shorefun
at 6:18pm 09.23.18
4/795
Not sure if this was covered before. The Plexus MA300 in 50mL has it is equivalent to Devcon Plastic
|
||
squarerigger
at 5:22pm 09.23.18
4/1394
just bought a 95 Santana 2023c and there is a tank /void/???? in the bow of the v berth forward of t
|
||
Keel locking pin (3)
kclancy
at 3:18pm 09.23.18
57/3568
Hi all, I finally got tired of all the water i would have in my boat after a day or two of sailing.
|
||
Charlie of Sarasota
at 2:42pm 09.23.18
8/370
My roller fueler was damaged in a storm. Only the luff was damaged and I want to replace the panels
|
A story of the engine that could.... Then didn't
RoyS at 4:53am 08.13.23 When it fell beneath the level of the Heat exchanger, a siphon event occurred and water flowed up f |
||
Oday 20 Restoration
shemandr at 3:57am 08.13.23 Welcome. Check in here for advice and encouragement. Chances are very good that someone on this lis |
||
Measurements of the Cutlass Bearing?
RSHunter27 at 10:07pm 08.12.23 Is the shaft bronze or SS ? Also, when you get down there, check whether the shaft is centred in t |
||
need to know ohm of water level for 1997 hunter 310
Ralph Johnstone at 8:35pm 08.12.23 @CharlieAnn , have you come up with a make and model of your current level sensor as requested in po |
||
New owner!
Vincent Williams at 8:05pm 08.12.23 She is in the water at Safe Harbor Pilots point hull #11 Quite an ordeal getting boat and trailer he |
||
Measurements of the Cutlass Bearing?
Ralph Johnstone at 7:18pm 08.12.23 I disconnected the gearbox from the shaft and the engine re-fired and when not connected to the sha |
||
trailer info, Hunter 23.5, 1994
maddog2 at 6:20pm 08.12.23 Group, Does anyone have the Majic Tilt BG0088 trailer designed for the 240? Are the bunks and the |
||
Our Cherubini Chainplates Are 40+ Years Old -- Any Failures? (4)
chichiflys at 5:16pm 08.12.23 Yikes - yeah the backstay U-bolts are also on my list. Thanks for the tip. Seems like a much easier |
||
Topside Teak Trim
Gene Neill at 5:12pm 08.12.23 Remove it. That way you can re-bed it in the process, which probably needs to be done anyway. Two bi |
||
2008 H36 microwave replacement
jssailem at 4:55pm 08.12.23 Along with enough spares to build a complete boat from scratch Coffee powered boat building.. Noth |
||
Measurements of the Cutlass Bearing?
RSHunter27 at 4:54pm 08.12.23 Thank you for your reply. It was these numbers that I was looking for. Might I ask what year your h2 |
||
Measurements of the Cutlass Bearing?
heritage at 4:52pm 08.12.23 This is the one that fits my H27:. Morse BLACKFISH 1 X 1 1/4 X 4 Brass Bearing It is about an inch |