Serving sailors online since 1997
 
 

Recent Topics

John Manfredi at 9:14am 01.19.00
1/1155
My 91 Cat 30 has a factory painted mast. The mast's outside surface has some paint blistering (I hav
Darrel Richards at 8:04am 01.19.00
9/1327
Been reading alot of info from this site. Have a couple of questions. Looking for a diagram and pa
Bob Peters at 7:51am 01.19.00
0/941
I have a stainless steel 48" wheel to trade. I would like a 36" wheel. If interested, toss in an eq
Tim at 6:18am 01.19.00
1/1285
I'm looking at a '82 Catalina 25 for my first sailboat. The boat is in generally overall good condi
Steve Dion at 3:41am 01.19.00
2/1030
Bill: I am interested in putting a roller furling jib on my H'31. We are located up in the Delta a
Dennis Thomas at 3:22am 01.19.00
6/1748
When I slide the main companionway hatch open or closed, it often emits a terrible screech of fiberg
George Lamb at 3:21am 01.19.00
1/1047
Well, we are getting closer on the delivery of our new 460. Since my wife and I are assignment in So
Brad at 3:20am 01.19.00
6/1550
I was wondering if anyone has experience/suggestions about getting to the packing glands on both the
Joe R at 3:01am 01.19.00
15/1297
Does anyone know if Hunter will offer an alternative to the stock clam cleats on the H240? Somethin
Jeff Rainey at 2:15am 01.19.00
2/1783
I am looking to buy a clean Capri 26" with an inboard diesel and a wing keel. If anyone knows where
Colin Campbell at 1:50am 01.19.00
0/1017
I wish to install an anchor roller on my 33.5 and would like to know what others have done to accomp
Scott at 1:36am 01.19.00
4/1187
After a week of cruising with family in the San Juan Islands last summer, I have tried to figure out
Jim Randall at 1:25am 01.19.00
0/842
The European Rendezvous 2000 is being hosted by the Legend Owners Association and will be held at Co
Jerry Jabes at 1:10am 01.19.00
9/1254
I purchased a 81 37C, 4 ft draft, several weeks ago and have not had time to bring it home from Pens
Mitch at 12:13am 01.19.00
2/1143
Has anyone seen taffrail seating on a 25. I'm buying a 1984 and was wondering if and how it could be
Dave Oberholtzer at 8:21pm 01.18.00
2/1094
I have a 96 H26 with the wheel kit installed and I am interested in bringing the jib line to the aft
Mike Elmore at 7:53pm 01.18.00
13/4013
I'm in the market this spring for a CQR anchor/rode. Anyone have a good recommendation for CQR weig
bill manning at 12:19pm 01.18.00
5/1037
i am currently looking at a h25'81 can anyone offer a must checklist for this boat? i have always
John Van Wagoner at 10:45am 01.18.00
5/1246
Hey 410 owners Carol, Chris, John, and others: do you guys worry about your diesel engine getting en
Bruce Stone at 10:38am 01.18.00
1/940
One of my most embarassing moments was when I had a new Hunter 23.5 and sailed out of Oxnard, Califo

Recent Replies

1991 P42 Bow Rollers
Rich Stidger at 1:30pm 01.25.20
How much $? I looked at their website. Unless I was looking in the wrong place, the 3" rollers st
Anyone use a CPAP when they anchor or moor out?
quadrille38 at 1:21pm 01.25.20
My cpap (and I assume most do) uses a transformer to step the 110 v down for use in the machine. So
Anyone use a CPAP when they anchor or moor out?
SFS at 12:47pm 01.25.20
I slept with mine every night for the 6 months we were on the boat in 2018, most of which was at anc
Anyone use a CPAP when they anchor or moor out?
dlochner at 12:19pm 01.25.20
An easier solution might be a battery operated travel CPAP machine. https://www.travelcpapmachine.c
high water?
Terry Cox at 10:47am 01.25.20
Who or how should adaptation be accomplished, appears to be the question. John, your winter Avatar
high water?
jon hansen at 10:45am 01.25.20
michigan/huron went up 3" in just this past week. now at record level
1991 P42 Bow Rollers
Terry Cox at 10:40am 01.25.20
Just ordered replacement rollers from Merimarine in WV. Good reviews fast reply will post after del
Thought on Hunter 45 for newbie.
jon hansen at 10:35am 01.25.20
opinion: a 45' boat is way easier so sail than a 30' boat i'm sure i'll get some blowback :)
Galvanic Corrosion
smokey73 at 10:33am 01.25.20
To bore you a bit more, I found some research, by the US Navy, on Galvanic corrosion. Taken from th
Thought on Hunter 45 for newbie.
Terry Cox at 10:32am 01.25.20
Our first boat was an H28 to see whether we found cruising PNW waters of interest. Sailed her for th
Replace shaft and cutlass   (3)
paulj at 10:31am 01.25.20
I had the strut bearing replaced and the shaft was OK, but I went with a split flange that was faced
Thought on Hunter 45 for newbie.
jon hansen at 10:21am 01.25.20
hunter 45' ish sailboat will make a "GREAT" starter boat for bay and coast cruising. lot's of prou
high water?
dlochner at 9:56am 01.25.20
Found these 2 videos about the Lake Ontario Flood in 2017 and about how the IJC manages lake levels.
Galvanic Corrosion
JamesG161 at 9:18am 01.25.20
To bore you a bit more, I found some research, by the US Navy, on Galvanic corrosion. Taken from the
Thought on Hunter 45 for newbie.
DayDreamer41 at 9:04am 01.25.20
Bigger the boat the bigger the commitment, the more comfort, the more cost, the higher the maintenan
Thought on Hunter 45 for newbie.
Dave Groshong at 8:37am 01.25.20
I recommend going in the 30ft range for starters, you'll save a ton of money and it just a much eas
Replace shaft and cutlass
JK_Boston_Catalina310 at 8:25am 01.25.20
No reason. We found cheaper at a local yard. Switched to a split coupling too.

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.